Related Manuals for SilverStone HFJ-700A
Summary of Contents for SilverStone HFJ-700A
- Page 1 Instruction Manual FORKLIFT JACK HFJ-700A 7000kgs CAPACITY NOTE: Owner / Operator must read and understand this instruction manual before using the forklift jack.
-
Page 2: Table Of Contents
contents 1. SPECIFICATIONS-----------------------------------2 2. IMPORTANT------------------------------------------2 3. FEATURES--------------------------------------------3 4. OPERATING INSTRUCTIONS------------------4 5. SAFETY TIPS-----------------------------------------7 6. MAINTENANCE INSTRUCTIONS--------------10 7. PUMP PRRMING INSTRUCTIONS-----------10 8. PLACARD PARTS LIST--------------------------11 9. PARTS LIST ﹠ EXPLODED FIGURE-------12... -
Page 3: Specifications
Warning symbol: This symbol is used to warn you of specific situations which may occur and must be avoided when using the HFJ-700A jack. Failure to WARNING observe these warnings may result in personal injury and/or property damage. -
Page 4: Features
You must refer this manual to all operators, using the HFJ-700A jack. They must read and understand the contents of this manual. This manual is written in English. If the equipment is to be used by operators who cannot read or understand English, it is the responsibility of the owner (or his designated representative) to instruct these people in the use of the jack. -
Page 5: Operating Instructions
OPERATING INSTRUCTIONS: 1. To raise: close the release valve(turn the knob clockwise) then pump the handle. 2. To lower: turn the release valve SLOWLY counter-clockwise. When lowering the jack lift truck. It is important to keep the rate of lowering under your control. - Page 6 When lifting from the end place the HFJ-700A at the Fig.3 centre of the fork lift truck. Always chock the wheels at the opposite end of the fork lift. When lifting 3 wheeled lift trucks, never lift the 2 wheeled end.
- Page 7 HFJ- 700A lack as a lifting contact point. 7. Raise a fork lift with the HFJ-700A only when: a. The forks are in a lowered position b. There is no load of any kind on the forks c.
-
Page 8: Safety Tips
Do not attempt to lift from a polished or greasy floor. 2. The HFJ-700A may be used to lift from either side or end of the fork lift truck. However, 2 wheels of the lift truck must remain firmly on the floor. - Page 9 5. Do not use the HFJ-700A to raise all for 4 wheels of the fork lift from the floor. Two wheels of the lift truck must remain in contact with the floor at all times.
- Page 10 The scissors action of the lifting mechanism can cause serious injury. 9. Do not drop, throw, drive over or otherwise abuse the HFJ-700A. The jack must be treated with the same care as any other precision tool upon which your safety and the safety of your co-workers depends.
-
Page 11: Maintenance Instructions
2. Oil the handle joints while operating the pump handle to work the oil 3. Although the hydraulic unit on the HFJ-700A is a sealed unit and will probably never need fluid adding to the reservoir, the following instructions shall be followed in the event fluid is needed: To refill the reservoir, place the jack in normal upright position, and completely lower jack by opening release knob. -
Page 12: Placard Parts List
HFJ-700A PLACARD PARTS LIST ITEM DESCRIPTION REQ’D Warning Label (Use Stands to Support Vehicle) Jack Position Plate Lift Pad Instructions Identification Piacard,HFJ-700A Warning Label(Do Not Adjust) WARNING NOTICE POSITION LIFT PAD HFJ-700A WARNING... -
Page 13: Parts List ﹠ Exploded Figure
DESCRIPTION DESCRIPTION Screw Back-Up Ring Lock Washer Plunger Trunnion Retaining Ring Frame 1 Screw Washer Link Rod Axle O-Ring Snap Ring Back-Up Ring Washer O-Ring Wheel Oil Tank Frame 2 O-Ring Screw Port Ring Lock Washer Cylinder Piston Spacer Valve Seat O-Ring Saddle Release Rod...
Need help?
Do you have a question about the HFJ-700A and is the answer not in the manual?
Questions and answers