Summary of Contents for ZheJiang Libiao Robotics LBAP-102LU-900
- Page 1 ZheJiang Libiao Robotics Co.,Ltd. LBAP-102LU-900 Wireless Communication Device Instruction Manual V1.0 2018.7 Note: The picture of this manual is for reference only.
- Page 2 FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
-
Page 3: Table Of Contents
Catalogo 1. Product Introduction .……………………………………..1 1.1 Product series…………………………………………………………………..…………..1 1.2 Product Usage…………………………………………………………………………….… 1 1.3 Product Features ……………………………………………………………………...……1 1.4 Electrical Specification…………………………………………………….……………….. 1 1.5 Electrical Parameter…………………………………………………………………..……...2 2. Product Structure and Composition……………………..2 2.1 Product Appearance Structure and Size …………………………………………………..….3 ……………………………………………………………..….3 2.2 Panel Wiring Instructions 3. -
Page 4: Product Introduction
Wireless Communication Device Instruction Manual 1、Product Introduction 1.1 Product model description LBAP-102LU-900: Corresponding to 902-928MHz 1.2 Product Usage Wireless communication device is mainly used in automatic sorting system robot of our company, which is used for wireless communication between server equipment and robots, replacing the WIFI communication method of traditional robot. -
Page 5: Electrical Parameter
1.4.1 working power supply POE: 44 ~ 57V / 150mA； USB:5V / 500mA； 1.4.2 Environmental requirements a. Environmental pressure: 86 kPa～106 kPa b. Environment temperature: -40℃～+85℃ c.Air relative humidity: 10% ～90%, relative humidity, no condensation (at＋25℃）； d.Environment without significant shaking or violent shock vibration 1.5 Electrical Parameter GFSK Modulation... -
Page 6: Panel Wiring Instructions
Picture 1 Appearance structure of wireless communication device Panel Wiring Instructions Piture 2 Panel Wiring Instructions As shown in the picture 2, the panel is shown as follows: 1. Thernet interface with POE power supply. 2. USB interface, connect to the computer. 3. -
Page 7: Product Usage Setting Instructions
The light is on, indicating that the network port receives the data. The light is on, indicating that the USB receives the data. 4. Reset botton (restore factory settings) 3、Product Usage Setting Instructions 3.1 Reset As shown in picture 2, press the button to keep the four lights R1, R2, M1, M2 all on and then release, the device IP will be restored to the factory settings, the factory setting IP address is: 192.168.0.200;... -
Page 8: Device Ip Settings Instructions
communication. 3.4 Device IP Settings instructions Open the software APLoopback Test, as shown in the picture 3: Picture 3 First ,change the IP address as shown in the picture 4 to the current IP address of the wireless communication device, for example, 192.168.0.200. Picture 4 Enter the IP address you want to set as shown in the picture 5, for example, 192.168.1.100 , and then click to set , the display is successful, it’s successful ,... -
Page 9: Minimum System Topology
Pictur 5 You can use this software to test whether the IP address has been set successfully .Input the IP address you set into the picture box, and click to test. As shown in the picture 6. Piccture 6 If the display is successful, the setting is successful , if the display fails, the setting fails , if the display times out, it indicates that the communication is bad, as shown in the picture 7. - Page 10 Picture 8 Minimum system TOP diagram As shown in the picture 8, the minimal system topology for Ethernet connections. The server is connected to the wireless communication device through the POE switch, and the POE switch provides power support for the device while communicating with the wireless communication device.When the server needs to interact with the robot, the server communicates with the wireless network device through UDP, then the wireless network device transmits data through...
Need help?
Do you have a question about the LBAP-102LU-900 and is the answer not in the manual?
Questions and answers