2. Block & Circuit Diagram 3. Component Layout 4. Part List 5. Accessories - Desktop Charger - Travel Charger - Cigar Lighter Charger - Hands Free Kit 6. WLPST ( LGIC Product Support Tool For Win95 ) LGIC LG Information & Communications, Ltd.
Page 3
- IS-99 : Short Message Service, Asynchronous Data Service, and G3 Fax Service LGC-500W is composed of a transceiver, a desktop charger, two Li-Ion Batteries (1650mAh), a hands-free kit, a travel charger. In digital mode, the hands-free kit is designed to operate in full duplex.
Multiple access techniques are used to share the available channel resources(frequency bandwidth). Frequency Division Multiple Access(FDMA), Time Division Multiple Access(TDMA), Code Division Multiple Access(CDMA) are the three major techniques in cellular systems. LGIC LG Information & Communications, Ltd.
Page 5
Old-fashioned radio receivers separate stations or channels by filtering in the frequency domain. CDMA receivers do not eliminate analog processing entirely, but they separate communication channels by means of a pseudo-random modulation that is applied and removed in the digital domain, not on the basis of LGIC LG Information & Communications, Ltd.
Page 6
Reducing the number of sites needed to support any given amount of traffic Simplifying site selection Reducing deployment and operating costs because fewer cell sites are needed Reducing average transmitted power Reducing interference to other electronic devices Reducing potential health risks LGIC LG Information & Communications, Ltd.
Moreover, the backward closed loop power control used by the mobile station to control power with the commands issued out by the cell site. The cell site receives the signal of each corresponding mobile station and LGIC LG Information & Communications, Ltd.
Page 8
The call conversion is carried out through the original call connection cell site, both cell sites, and then, new cell site. This method do not change frquency , so minimize call disconnection and prevent the user from detecting the hand-off. LGIC LG Information & Communications, Ltd.
Page 9
In addition, in the CDMA system, services and service charges are classified further into different classes so that more transmit power can be allocated to high class service users for easier call set-up; they can also be given higher priority of using hand-off function than the general users. LGIC LG Information & Communications, Ltd.
(AGC Amp). Then, they are converted into RF band by the frequency synthesizer synchronizing these signals to proper output frequencies. Transmit signals obtained pass through the duplexer filter and then, are sent out to the cell site via the antenna. LGIC LG Information & Communications, Ltd.
IB bracket with the four self-tapping screws provided. Clip the IB into the IB bracket. 5.3.4. Microphone Installation Install the microphone either by cliiping I onto the sunvisor (driver’s side) or by attaching it to door post (driver’s side), using a velcno adhesive tape (not included). LGIC LG Information & Communications, Ltd.
Page 17
Connect the kit’s power cable connector to the interface box power receptacle. 5.3.5.2 Antenna Cable Connection Connect the antenna coupler cable connector from the cradle to the external antenna connector. ( Antenna is not included.) LGIC LG Information & Communications, Ltd.
• Edit ESN(if you want, but not recommended) , then press [OK]. NAM 1 PHONE NUMBER • Enter the phone number, then press [OK]. NAM 1 HOME SID • Edit NAM 1 HOME SID, then press [OK]. LGIC LG Information & Communications, Ltd.
Page 19
NAM 1 CDMA HOME SID 4 NAM 1 CDMA HOME NID 4 NAM 1 AMPS PHONE NUMBER NAM 1 AMPS HOME SID PHONE MODEL SLOT CYCLE INDEX ¡ Ø Editing this items is not recommended. LGIC LG Information & Communications, Ltd.
Dupl VC - 19.68M Hz exer Tcxo 19.68M Hz LNA_Range SYNTH_LOCK Tank IFR3000 Down CDMA IF SAW Filter RX RF Mixer Filter DFM IF SAW Filter [Figure 1-1] Block Diagram of RF Transmit/Receive Part LGIC LG Information & Communications, Ltd.
Page 21
IF signals that have selected the FM path are inputed to FM IF BPF(F8) for FM through the FM path. IF signals that have selected the CDMA path are passed CDMA IF saw filter(F6) and then, are inputed to IFR3000. LGIC LG Information & Communications, Ltd.
Page 22
IF center frequency. The I/Q down converter outputs the CDMA I and Q signals haing the bandwidth of 1kHz ~630kHz through CDMA LPF. The use of LPF in IFR3000 suppresses spurious signals entering the receiver in order to improve the CDMA baseband signal selectivity. LGIC LG Information & Communications, Ltd.
Page 23
FM analog I and Q baseband components are converted to digital FM(DFM) signals by two 8-bit ADCs. The FM ADCs’ outputs are inputted into MSM3000 through RXIFMDATA and RXQFMDATA terminals. LGIC LG Information & Communications, Ltd.
Page 24
OUT+ and OUT- of IFT3000 and mixes the output of Dual PLL Module with UHF output signal. Upconverter’s output operation range is 800MHz~960MHz (RF frequency) and has the conversion gain of 5 dB. In addition, the suppression of spurious signals which are unwanted noise(885kHz offset) is about -50 dBc when LGIC LG Information & Communications, Ltd.
Page 25
The maximum power of that can be inputted is 5W (Max) and IL is 0.65dB (Max). Input/output separation is at least 15dB (Min). LGIC LG Information & Communications, Ltd.
Page 26
PIN3 are inputted into IFR after going through the VRACTOR diode and tank circuit so that the outputs of IFR internal receive end VCO are adjusted to 170.76MHz. PLL that generates the LO frequency of a mobile station have good spurious characteristics (ref. supurious at 30kHz from carrier = -70dBc (Max)). LGIC LG Information & Communications, Ltd.
The power supply part is made up of 5 Regulators and direct connet to Batt. Regulator(150mA )s give the power each Circuits(TX chain, RX chain, IFT and ITR, Codec). Regulator(200mA) gives the power MSM and memory . PAM, Motor, LED is directly conneted to Batt. LGIC LG Information & Communications, Ltd.
Page 28
These signals are amplified with programmable gain on codec’s internal AMP and transferred to the ear piece. Then, the signals of ringer activate the ringer is generated in MSM3000 and drive the ringer circuit(Q10, Q11). LGIC LG Information & Communications, Ltd.
Page 29
During the phone is on operating state, LDO for MSM is always enable and gives the power MSM and memory part LDO for IFT_IFR are always enable and gives the power IFT, IFR and VC-TCXO. LGIC LG Information & Communications, Ltd.
Page 30
LCD MODULE LCD module contains a controller which will display the information onto the LCD by 8-bit data from the MSM. It has a black and white full graphic 112(W) ¥ ¹ 64(H) dots LGIC LG Information & Communications, Ltd.