Logan F400-1 Instruction Manual

L988N1 F400 Manual 8-11:Fitting Tool 5L 8_17.qxd

Instruction Manual

P I C T U R E F R A M I N G
FITTING TOOL
U.S. Patent No. 6,896,168
Identification
Lock Plate
Foot
Bumper
Turret
Preparation
A. Fill frame
1. Turn over frame.
Fig. 1
2. Load glass, matboard and image and
backing material into frame (Fig. 1).
B. Choose an insert (Fig. 2).
1. Flexible Insert- Bendable insert used
in photo frames where material can
easily be changed. Moulding
Brad Nails - Economical insert.
Can be used for securing canvas.
Multipoint Insert - Bendable insert
and used to hold fillets in place.
Rigid Insert - Firm insert used in
permanent applications.
continued on next page
Preparation continued
B. Choose an insert (continued)
2. Rotate turret so insert choice faces
Fig. 3
foot (Fig. 3).
C. Determine insert spacing and quantity
1. Corner spacing is generally 1" (3cm)
to 2" (5cm) from corner.
2. Side spacing is generally 4" (10cm)
to 5" (13cm) apart (Fig. 4).
8/17/11 1:18 PM Page 1
Description
The Model F400-1 Fitting Tool has been
designed to provide long lasting quality opera-
tion with easy to use features. It's primary
purpose is to drive pins, points and nails into
wood picture frame moulding to securely hold
framing materials in place. The Model F400-1
Fitting Tool features a unique and revolution-
ary rotating turret to accommodate all of the
most popular style points.
Lever - Moveable handle which drive inserts.
Foot - Sliding stop block.
Lever
Lock Plate - Locks foot secure.
Turret - Insert holder which rotates. Holds four
insert styles.
Flexible Insert - Bendable insert used to hold
framing material inside frame.
Insert
Backing Material
(Foamboard or Cardboard)
Matboard or image
Glass
Fig. 2
Brad
Multipoint Rigid
Flexible
Nail Insert Insert
Insert
Fig. 4
Model F400-1
Operation
A. Driving Insert
1. Slide foot away from turret.
2. Load insert into turret slot. Be sure
point end faces out (Fig. 5).
3. Align body and tip of insert against
frame. Rest body on framing materi-
www.logangraphic.com
al. Slide foot until bumper rests firm-
ly against frame (Fig. 6).
L988N1 08/11
1
4. Firmly squeeze handle and drive insert into the wood until turret stops
against frame (Fig. 7).
Note-for best results keep body flat on material while squeezing.
5. Squeeze lock plate on foot and rotate foot to release (Fig. 8).
6. Slide body back along top of framing material to remove from insert. Do
not lift up, but rather pull straight back.
7. Repeat to finish.
2
Trouble Shooting
Problem:
Points bend when being inserted.
Solution:
Try using a different insert more suited to hardwood.
Make sure the turret is resting flush on back material being framed.
Problem:
Mats or framed material buckles after being secured.
Solution:
Let the turret rest gently on back of material when inserting points.
Do not angle inserts down to "pinch" material being secured.
Problem:
Fitting Tool handle does not release after point insertion.
Solution:
Release pressure by squeezing lock plate on the foot and swivel foot
to clear moulding, then withdraw turret in opposite direction of insertion.
3
Instruction Manual
L969
L811
L964-N
L970
L967
L963
L975
Fig. 5
Logan Graphic Products, Inc. ("Logan") warrants the Fitting Tool -
Model F400-1, to be free from defects in parts and workmanship for a
period of one year from the date of original purchase. Logan warrants
that it will either repair or replace, at it's sole discretion, any neces-
sary replacement parts found to be defective. Should the product
need to be returned to Logan for repair or replacement parts, authori-
zation for any return must come from Logan in writing. Costs of
returning the product to Logan, including insurances, shall be borne
by the purchaser. Logan shall not be liable for any damages or losses,
incidental or consequential, direct or indirect, arising from the use of
this product. This warranty extends only to the original purchaser and
is not assignable or transferable. This warranty is in lieu of all other
warranties, expressed or implied. Be advised that any Logan products
purchased as "new" from an unauthorized dealer, such as an online
auction site or similar, may be void of their warranty.
FITTING TOOL
No.
L811
L966
L963
L972
L964-N
L965
L966
L967
L968
L965
L969
L978
L970
L972
L977
L976
L975
L968 L976
L977
L978
4
Fig. 6
5
Model F400-1
Fig. 7
Fig. 8
6
Warranty
7
Model F400-1
Description Qty.
Lock Plate Spring 1
Bumper 1
End Cap 1
Handle 1
Body 1
Turret-Top 1
Turret-Bottom 1
Lock Plate 1
Foot 1
Drive Rod 1
Turret Screw 4
Pivot Screw 1
Ball 1
Ball Spring 1
Logan Graphic Products, Inc.
1100 Brown Street, Wauconda, IL 60084 USA
Phone 1 847 526 5515 Toll Free 1 800 331 6232
www.logangraphic.com