Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for LT Security LTK1101 Series
- Page 1 LTK1101 & LTK1104 Series Card Reader User Manual...
- Page 2 Card Reader User Manual User Manual About this Manual This Manual is applicable to Card Reader. The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
- Page 3 Card Reader User Manual Regulatory Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
- Page 4 Card Reader User Manual 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points.
- Page 5 Card Reader User Manual Warnings Follow these Cautions Follow these safeguards to prevent precautions to prevent potential serious injury or death. injury or material damage. Warnings All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region.
- Page 6 Card Reader User Manual Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage). ...
- Page 7 Card Reader User Manual Preventive and Cautionary Tips To guarantee the card reader works properly, please read and obey the notes below. If the card reader is powered by the controller, the power supply distance is recommended to be no longer than 100m. If the distance is longer than 100m, you are advised to power the card reader by external 12V (range: -%10 ~ +%10) DC power supply, which is nonswitched and linear.
-
Page 8: Table Of Contents
Card Reader User Manual Content Chapter 1 Introduction ............2 Front View ..............2 Rear View ..............3 Side View............... 4 Chapter 2 Installation ............6 Installing PSAM Card ............. 6 Introduction for DIP Switch ........... 6 Definition of Cable ............7 Wiring Cables .............. -
Page 9: Chapter 1 Introduction
Card Reader User Manual Chapter 1 Introduction The card reader is a kind of high-performance product, with a 32 bit high-speed processor. It communicates with access controller via either RS-485 protocol or Wiegand protocol. And a build-in tamper-proof module helps to protect card reader from malicious damage. -
Page 10: Rear View
Card Reader User Manual Figure 1-3 LTK1104MK Figure 1-4 LTK1104M 1.2 Rear View The rear view of card reader is shown below: Figure 1-5 Rear View of LTK1101... -
Page 11: Side View
Card Reader User Manual Figure 1-6 Rear View of LTK1104 Description of Rear View Table 1-1 Name Cable Interface of RS-485, Power, LED Control, etc. Buzzer Tamper-proof Module DIP Switch PSAM Card Slot (available for CPU card reader) 1.3 Side View The side view of card reader is shown below:... - Page 12 Card Reader User Manual Figure 1-7 LTK1101 Figure 1-8 LTK1104...
-
Page 13: Chapter 2 Installation
Card Reader User Manual Chapter 2 Installation 2.1 Installing PSAM Card PSAM card slot is only available for CPU card reader. Insert the PSAM card into the slot according to the direction shown below. Figure 2-1 PSAM Card Slot 2.2 Introduction for DIP Switch The DIP switch module is shown below. -
Page 14: Definition Of Cable
Card Reader User Manual Figure 2-3 DIP Switch Module Description of DIP Switch Table 2-2 Description DIP Switch Status 1: 1 1 ~ 4 Address of RS-485 0: 0 Read card No. or file in card. 1: read card No; (Only available for CPU card 0: read file in card. -
Page 15: Wiring Cables
Card Reader User Manual Color Description Purple Beep Control (available for Wiegand Protocol) Gray Case Sensor (available for Wiegand Protocol) Green Wiegand W0 (available for Wiegand Protocol) White Wiegand W1 (available for Wiegand Protocol) Black Orange Red LED Control (available for Wiegand Protocol) PWR (DC +12V) 2.4 Wiring Cables Purpose:... - Page 16 Card Reader User Manual Controller Card Reader Figure 2-4 Wiring for RS-485 Communication Mode Steps for Wiegand communication mode: Set the DIP switch of No. 6 as 1. Set the DIP switch of No. 5 and 7 for reading card mode and Wiegand protocol.
-
Page 17: Installing Card Reader
Card Reader User Manual Controller Card Reader Figure 2-5 Wiring for Wiegand Communication Mode 2.5 Installing Card Reader Before you start: Set the DIP switch. For details, refer to 2.2 Introduction for DIP Switch. Steps:... - Page 18 Card Reader User Manual Fix the plate on the wall or other place. Connect the cables between controller and card reader. For details, refer to 2.4 Wiring Cables. Push the card reader to match the fixed plate. Fasten the screw to keep the components together.
-
Page 19: Chapter 3 Sound Prompt And Indicator
Card Reader User Manual Chapter 3 Sound Prompt and Indicator After the card reader is powered on, LED status indicator will turn blue and blink for 1 time. Then it will turn red and blink for 3 times. At last the buzzer will send out a beep sound indicating the starting up process is completed. - Page 20 Card Reader User Manual LED Indicator Status Description card is invalid. For RS-485 protocol: Registering failed or Red and blinking card reader is offline. Red and Keeping Available for reading file mode of CPU rapidly blinking card: PSAM is not inserted or undetected. Red and keeping Failed to get key files of PSAM card;...
Need help?
Do you have a question about the LTK1101 Series and is the answer not in the manual?
Questions and answers