............. Using the Aeris DAC Volume Control! ............. Digital Versus Analogue Volume Control! ............Using Aeris DAC with a Preamplifier! .............. Using the Aeris DAC Directly with an Amplifier! ..........Audio Output Connections! ................Digital Audio Input Connections! ..............Specifications! ....................
85 to 265 VAC without any adjustments necessary. must not be modified in any way, other than according to official AERIS DAC service bulletins from Jeff Rowland Design Group. Otherwise, the factory warranty will be immediately voided. When operating the...
REAR PANEL SYMBOLS The crossed-out wheeled bin is the European Union symbol for indicating separate collection for electrical and electronic equipment. This product contains electrical and electronic equipment which should be reused, recycled or recovered and should not be disposed of with unsorted regular waste.
If you have any additional questions regarding the installation or operation of the AERIS , please contact your authorized Jeff Rowland Design Group dealer or check the Jeff Rowland Design Group web site at http://jeffrowland.com. Enjoy the music!
TECHNICAL FEATURES IsoSyncECS Isolated Synchronous Error Correction System. Based upon an asynchronous buffer, voltage controlled crystal oscillators, and a 24 bit D/A converter – all under the precise control of an FPGA (Field Programmable Gate Array) running proprietary algorithms. BIT PERFECT AND Bit perfect conversion with total jitter output noise of less than 10 VIRTUALLY JITTER picoseconds RMS from any input –...
Page 7
6-LAYER CIRCUIT Multi-layer circuit boards provide extremely low impedance BOARDS ground and power distribution for remarkably low digital noise contamination. HIGH-PRECISION Extensive use of Lead (Pb)-free, low temperature coefficient, SURFACE MOUNT active and passive surface-mount components results in COMPONENTS significantly smaller loop areas, reduced circuit capacitance and inductance, and introduces less noise than conventional leaded components.
Page 8
MAINTENANCE AND CARE All Jeff Rowland Design Group products are designed to provide a lifetime of enjoyment and listening pleasure. Chassis is sealed to prevent dust from entering the interior of the chassis and thus should never need interior cleaning during the lifetime of the product. All internal circuitry is maintenance-free such that no adjustments of any kind are necessary over the lifetime of the product.
Neither Jeff Rowland Design Group nor the shipper can be held responsible for damages incurred during transit if the original factory packing is not used. All factory returns require that Jeff Rowland Design Group issue a Return Authorization (RA) number prior to shipment.
USB IN One (1) USB ‘Type B’ input allowing direct connection to a PC via a Type B to Type A USB lead. The AERIS DAC operates independently of your PCs sound card. DC IN POWER INPUT One (1) DC Power supply cable is utilized to connect &...
Illuminated LED indicates a non-standard sample rate has been detected. LOCK Illuminated LED indicates a valid digital lock at the selected digital audio input at the indicated sample rate. Receives IR transmission from the AERIS DAC handheld & RECEIVER remote transmitter. MUTE Pressing the mute button will mute all outputs and illuminate the corresponding LED.
SUPPLY. POWER SWITCH Toggles operation between ON and OFF. Please ensure " that all connections are made between AERIS DAC, power supply, and AC Mains wall outlet before turning switch to ON position. FUSE ACCESS Access for power supply fuse. Fuse type GDC 630ma SLO- BLO.
TOSLINK, BNC1, and BNC2. MUTE This button will immediately mute the outputs of . Pressing the button a second time AERIS DAC will reactivate the outputs. VOL UP / VOL DOWN Adjusts the main input volume. Press the right button to increase volume. Press the left button to decrease volume.
REMOTE TRANSMITTER BATTERY REPLACEMENT handheld remote transmitter is powered by 2 standard alkaline AA AERIS DAC batteries. When the remote transmission range decreases or no longer operates, the batteries need to be replaced. Using a standard flat blade screw driver, unfasten the holding screw located in the bottom end of the transmitter unit.
USING THE AERIS DAC VOLUME CONTROL is designed such that the volume control attenuates the signal up to 32 AERIS DAC dB below the point of LED flashing. When the right LED starts flashing, the AERIS DAC begins digital multiplication to increase the volume up to 20 dB above full scale. This would be for direct drive applications where the user would like to "rock out"...
AERIS DAC control is in its normal position at a normal listening level. USING THE AERIS DAC DIRECTLY WITH AN AMPLIFIER has a sufficient output level to drive any power amplifier directly. The AERIS DAC...
AUDIO OUTPUT CONNECTIONS Note: Do not turn on the unit until all connections have been made. BALANCED For best results, use one (1) pair balanced XLR line outputs to connect your preamplifier or amplifier whenever possible. UNBALANCED Use these one (1) pair unbalanced RCA line outputs if "...
fiber-optic interconnect cable designed specifically for audio use. One (1) USB ‘Type B’ input allowing direct connection to a PC via a Type B to Type A USB lead. The AERIS DAC operates independently of your PCs sound card. !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!"#$%!)/!'(!&)
SPECIFICATIONS INPUTS 1x USB (B- Accepts up to 24 bit PCM at 44.1, 48, type)! 88.2, and 96 kHz sample rates 1x Toslink (Optical) Accepts up to 24 bit PCM from 11 - 192 kHz sample rates 2x SPDIF (RCA) Accepts up to 24 bit PCM from 11 - 192 kHz sample rates OUTPUTS...
Jeff Rowland Design Group, Inc. Said determination shall be made as soon as possible following receipt of the product. Jeff Rowland Design Group, Inc. may, at its option, require from the purchaser, valid proof of purchase (dated copy or photocopy of dealer's original invoice).
Jeff Rowland Design Group, Inc. does not authorize any third party, including any dealer or representative, to assume any liabilities on its behalf or to make any warranties on its behalf unless authorized to do so. Warranty registration cards must be completed and mailed to Jeff Rowland Design Group, Inc.