Summary of Contents for Sam IQFDA31
- Page 1 User Manual IQFDA31 Dual Channel 3G/HD/SD-SDI Re-clocking Distribution Amplifier with Fiber I/O www.s-a-m.com...
-
Page 2: Information And Notices
Information in this manual and software are subject to change without notice and does not represent a commitment on the part of SAM. The software described in this manual is furnished under a license agreement and can not be reproduced or copied in any manner without prior agreement with SAM or their authorized agents. -
Page 3: Table Of Contents
5.8.2 Configure Type ..........24 Issue 1 Rev 1 Page 3 © 2016 SAM... -
Page 4: Introduction
Introduction 1.1 Description The IQFDA31 provides dual HD-SDI 3 Gbit/s, 1.5 Gbit/s, or 270 Mbit/s SD-SDI inputs with both SDI and fiber optic outputs in a single-width package. Flexible routing of inputs and outputs allows the module to operate as a single- or dual-channel mixing fiber and copper I/O. -
Page 5: Feature Summary
IQFDA31 Introduction 1.3 Feature Summary The IQFDA31 provides the following features: • Dual-channel intelligent 3 Gbit/s SDI, HD-SDI, and SD-SDI re-clocking distribution amplifier. • Flexible selection of inputs allows single- or dual-channel operation. • Input signal monitoring allows auto-changeover emergency switching. -
Page 6: Enclosures
“B” order codes only. 1.6.2 A-style Enclosures Enclosure order code: IQH1A-S-P Enclosure order codes: IQH3A-S-0, IQH3A-S-P Enclosure order codes: IQH3A-E-0, IQH3A-E-P, IQH3A-0-0, IQH3A-0-P Enclosure order code: IQH1A-S-P Issue 1 Rev 1 Page 6 © 2016 SAM... -
Page 7: Technical Specification
*Dependant on SFP fitted Control Interface Up to 2 x GPI (I/O configurable) Electrical TTL compatible, active low driven Connector/Format BNC/ 75 Ohm panel jack on standard SAM connector panel Controls Indicators Power OK (Green) OK (Green flashing) Input 1... - Page 8 Reports the following module information: Software Version, Serial Number, Build Number, KOS Version, Firmware Version, PCB Version Specifications Electrical 3 Gbit/s SDI, SMPTE 424M 1.5 Gbit/s HD-SDI, SMPTE 292M 270 Mbit/s SDI, SMPTE 259M-C / DVB-ASI Issue 1 Rev 1 Page 8 © 2016 SAM...
- Page 9 Up to 30 Km @ 3 Gbit/s Up to 21 Km @ 1.5 Gbit/s Up to 10 Km @ 270 Mbit/s Power Consumption Module Power 4 W Max (A frames) Consumption 4 PR Max (B frames) Issue 1 Rev 1 Page 9 © 2016 SAM...
-
Page 10: Connections
IQFDA31 Connections Connections This section describes the physical input and output connections provided by the IQFDA31. 3.1 SDI Input Serial digital input is made to the unit via two BNC connectors which terminate in 75 Ohms. 3.2 SDI Outputs Serial digital outputs from the unit are made via four BNC connectors which terminate in 75 Ohms. -
Page 11: Card Edge Leds
The rate on input channel 2: • Both LEDs illuminated: 3 Gbit/s • Left LED illuminated: 1.5 Gbit/s • Right LED illuminated: 270 Mbit/s • Both LEDs off: Rate unknown Green Illuminated Input SFP Rx selected. Issue 1 Rev 1 Page 11 © 2016 SAM... -
Page 12: Operation Using The Rollcall Control Panel
IQFDA31 Operation Using the RollCall Control Panel Operation Using the RollCall Control Panel The IQFDA31 will dynamically configure itself depending on rear and SFP options. The Note: RollCall control panel will change to reflect the current product configuration. The screens shown in this section are for guidance and reference only, and may be slightly different to those on your module. -
Page 13: Input
Select Mute On Inp Err to apply a mute to the output if any rate other than those specified as valid in the Input 1 and Input 2 sections is detected. Select Mute to manually apply a mute to the output. Issue 1 Rev 1 Page 13 © 2016 SAM... -
Page 14: Sfp
Rx Power State: Displays the state of the received signal (options include OK, WARN:HI, WARN:LO, FAIL:LO and FAIL:HI). • Rx Power: Displays the signal level received at the input (in dBm). Issue 1 Rev 1 Page 14 © 2016 SAM... -
Page 15: Memory 1-16
The Last Recalled Memory pane displays the most recently recalled memory. If any of the settings have been changed since it was recalled, an asterisk will be displayed after the memory name. Issue 1 Rev 1 Page 15 © 2016 SAM... -
Page 16: Save Memory Name
To change a memory name: • In the Save Memory Name field, type the new memory name, and then click the S button. To return the memory to its default preset value, click P button. Issue 1 Rev 1 Page 16 © 2016 SAM... -
Page 17: Logging
The Logging Misc screen displays the current log information about the unit’s basic parameters. 5.5.2 Logging Inputs The Logging Inputs screen is used to select which fields should be enabled for each of the serial inputs. Issue 1 Rev 1 Page 17 © 2016 SAM... -
Page 18: Logging Sfp
IQFDA31 Operation Using the RollCall Control Panel 5.5.3 Logging SFP The Logging SFP screen is used to select which fields should be enabled for each of the SFP inputs. Issue 1 Rev 1 Page 18 © 2016 SAM... -
Page 19: Log Field Descriptions
Displays the TX power status. Valid values are: • • WARN:HI • WARN:LO • FAIL:LO • FAIL:HI OUTPUT_N_TX_POWER= The power level of the TX input, in dBm. OUTPUT_N_WAVELENGTH= The wavelength of the transmitted output signal. Issue 1 Rev 1 Page 19 © 2016 SAM... - Page 20 Displays the laser bias status. Valid values are: • • WARN:HI • WARN:LO • FAIL:LO • FAIL:HI N should be replaced with the respective SFP/output identifier, for example, 1 for an SFP Note: and B for an output. Issue 1 Rev 1 Page 20 © 2016 SAM...
-
Page 21: Rolltrack
LASER Bias current below limits. RX N Power OK Receive power is within limits. RX N Power High Receive power is above limits. RX N Power Low Receive power is below limits. Issue 1 Rev 1 Page 21 © 2016 SAM... -
Page 22: Address
The message is not being sent. The message is being sent. Internal Type Error Inconsistent behavior. Please contact your local SAM agent. 5.6.7 RollTrack Status A message is displayed here to indicate the status of the currently selected RollTrack index. -
Page 23: Setup
These are the input names displayed in logging. To change the name of Input 1 or Input 2, type the name in the text field and click S. To return the name to its factory default, click P. Issue 1 Rev 1 Page 23 © 2016 SAM... -
Page 24: Sfp Setup
When changing an SFP, the module needs to be restarted in order for the SFP to become Note: active. Before configuring the SFP, ensure that the correct SFP is installed. Issue 1 Rev 1 Page 24 © 2016 SAM...
Need help?
Do you have a question about the IQFDA31 and is the answer not in the manual?
Questions and answers