Advertisement
Program guide
Cleaning and care
Lint filters
Plinth filter
Cleaning the lint filters and air flow
openings thoroughly
Only clean the plinth filter when Clean lint
Removing visible lint
If the drying duration has become longer
and plinth filter See lights up.
Clean both lint filters in the door opening
or the surface of the filters is visibly com-
To turn the message off: Switch the dryer off
after every drying cycle.
pacted with lint, you should carry out the
and then on again. Confirm with OK.
following cleaning procedure.
ĺ
寿
Remove the fragrance capsule (if fit-
Press the round,
ĺ
ted).
Pull the upper lint filter forward to remove
indented area on
it.
the heat
ĺ
ĺ
Pull the upper lint
Turn the yellow
exchanger access
filter forward to
dial on the lower
panel to open it.
remove it.
lint filter in the
The access panel
direction of the
will spring open.
ĺ
arrow (until you
Pull the plinth filter
hear it click).
out by the handle.
ĺ
Hold the dial and
pull the lint filter
ĺ
Use your fin-
forward to
gers or a vac-
remove it.
uum cleaner to
A guide pin in the dryer will come out which
remove the lint
prevents the access panel from closing with-
from the surface
out the plinth filter.
ĺ
ĺ
of the filter.
Use a vacuum
Pull the handle
cleaner to
out of the plinth
remove any
ĺ
filter.
visible lint from
Clean the filter
the upper air flow
thoroughly under
openings.
running water.
ĺ
ĺ
Push the upper lint filter back into posi-
Squeeze the
tion until it clicks.
water out of the plinth filter thoroughly.
ĺ
ĺ
Close the door.
Flush the lint filters through with warm
寿
The plinth filter must not be replaced
running water.
ĺ
dripping wet.
Shake out the lint filters thoroughly and
ĺ
then dry them carefully.
Use a damp cloth
to remove any
寿
Ensure the filters are dry before replac-
lint.
ing them.
ĺ
Refit all of the lint filters and close the
door.
Frequently asked questions
Checking the heat exchanger unit
Some of the messages in the display are more than one line long. Touch the or sensor
button to read them in full.
寿
Danger of injury! Do not touch the
cooling fins with your hands. You could cut
Problem/Fault message
Possible cause and solution
yourself.
000
lights up after
Access via a PIN code has been activated.
ĺ
the tumble dryer is
You must enter the correct PIN code to use the tumble dryer.
Carefully vacuum
switched on and a
See "Settings menu – PIN Code" in the operating instruc-
up any visible lint
program cannot be
tions.
or dirt.
selected
The program is can-
The condensed water container is full or there is a kink in the
celed and the following
drain hose.
ĺ
lights up:
Empty the condensed water container.
ĺ
Refitting the plinth filter
ĺ
Empty container. See
Check the drain hose.
Fit the filter back
To switch off the message:
ĺ
on the handle.
Open and close the door while the dryer is switched on.
Make sure it is the
At the end of a program
There is a build-up of lint in the airways. See "Cleaning and
correct way
the following lights up:
care" in the operating instructions.
ĺ
round.
Clean the lint filter.
ĺ
Clean the lint and plinth
Clean the plinth filter.
filter See
To switch off the message:
ĺ
ĺ
Confirm with OK.
First insert the
handle with the
After a program has
There is a build-up of lint in the airways. See "Cleaning and
been interrupted, the
care" in the operating instructions.
plinth filter
ĺ
following lights up:
Clean the lint filter.
attached over the
ĺ
Clean the plinth filter.
two guide pins.
ĺ
Clean the lint and plinth
Cleaning the air flow openings.
ĺ
filter See
Clean the heat exchanger.
ĺ
To switch off the message:
The word Miele on the handle must be the
Switch the dryer off and then on again.
correct way up.
ĺ
End/Cooling down
The program has finished but the laundry has not yet cooled
Close the heat exchanger access panel.
down.
ĺ
Either remove the laundry and spread it out to cool down
or leave it in the tumble dryer to cool down during the
cooling phase.
Problem/Fault message
Possible cause and solution
The display is in a dif-
A different language has been selected in "Settings, Lan-
ferent language
guage ".
ĺ
Set the language you want. The flag symbol will guide you.
The display remains
There is no power to the dryer.
ĺ
Quick Start Guide
dark, and the Start/Stop
Check whether the plug is plugged in.
ĺ
sensor button does not
Check whether the fuse has tripped.
Heat-pump dryer
light up or flash
The dryer has switched off automatically to save energy.
ĺ
Turn the program selector to switch the dryer on again.
The laundry is not suffi-
The load consisted of different types of fabric.
ĺ
ciently dry
ĺ
Finish drying using the Time Dry drying program.
Select a more suitable program next time.
Tip: You can alter the residual moisture level for some pro-
grams. See "Settings menu – Drying levels" in the operating
instructions.
Items made of synthetic
Synthetic fibers tend to attract static charge.
fibers are charged with
Static charge can be reduced by adding a fabric softener to
static electricity after
the final rinse in the washing program.
drying
There is a build-up of
Lint is principally the result of friction when garments
lint
are being worn and to some extent when they are being
washed. Machine drying hardly causes any lint to form.
Lint is collected by the lint filter and the plinth filter and can
be removed easily.
See "Cleaning and care".
You can hear operating
This is not a fault. The compressor (heat pump) is operating.
noises (buzzing/hum-
No action required. These noises are normal and can be
ming)
heard when the compressor is operating.
These short instructions are not a substitute for the operating instructions supplied with
the appliance! It is essential to familiarize yourself with the dryer before using it for the first
time.
Take note of the operating instructions, as well as the "IMPORTANT SAFETY
INSTRUCTIONS".
en – US
M.-Nr. 10 671 340
Advertisement
