Before Starting Installation:
Retrofit
Check rough-in height to achieve 24" rim height (17" rim height for ADA).
Installation
Instructions
Check slope. Downhill slope, per code, is essential because waterfree urinals
depend on gravity flow.
-4000
WES
Check DWV material. Suitable materials include cast iron, PVC, ABS, and
Waterfree
galvanized steel. Do not install on copper DWV due to copper's susceptibility
Urinal
to corrosion.
Shut off water supply and cap the nipple with the
Customer Service:
Toll Free 888-SLOAN-14 (888-756-2614) • Fax 800-737-3061 • www.sloanvalve.com
Insert Tube Cutting Chart
4
Drain Nipple Depth
Trim
13
7
/
" or greater. . . . Do not cut
8
13
3
/
" or less . . . . . .
1
/
"
4
4
1
1
13
/
" or less . . . . . .
/
"
2
2
13
1
/
" or less . . . . . .
3
/
"
4
4
13"
or less . . . . . . 1"
12
3
/
" or less . . . . . . 1
1
/
"
4
4
12
1
/
" or less . . . . . . 1
1
/
"
2
2
12
1
/
" or less . . . . . . 1
3
/
"
4
4
12"
or less . . . . . . 2"
Use a flashlight to check pitch/slope.
3
1
11
/
" or less . . . . . . 2
/
"
There should be no water present in
4
4
11
1
/
" or less . . . . . . 2
1
/
"
2
2
the inspection disc or nipple. Remove
11
1
/
" or less . . . . . . 2
3
/
"
4
4
flange after inspection.
11"
or less . . . . . . 3"
3
1
10
/
" or less . . . . . . 3
/
"
4
4
9
10
1
/
" or less . . . . . . 3
1
/
"
2
2
10
1
/
" or less . . . . . . 3
3
/
"
4
4
10"
or less . . . . . . 4"
9
3
/
"
or less . . . . . . 4
1
/
"
4
4
9
1
/
"
or less . . . . . . 4
1
/
"
2
2
9
1
/
"
or less . . . . . . 4
3
/
"
4
4
9"
or less . . . . . . 5"
8
3
/
"
or less . . . . . . 5
1
/
"
4
4
8
1
/
"
or less . . . . . . 5
1
/
"
2
2
8
1
/
"
or less . . . . . . 5
3
/
"
4
4
Drill two more holes for the hanger
8"
or less . . . . . . 6"
7
3
/
"
or less . . . . . . 6
1
/
"
bracket, install screws, and tighten.
4
4
7
1
/
"
or less . . . . . . 6
1
/
"
Also drill holes for the lower anchor
2
2
7
1
/
"
or less . . . . . . 6
3
/
"
4
4
screws and insert plastic anchors.
7"
or less . . . . . . 7"
1
6
3
/
"
or less . . . . . . 7
/
"
4
4
14
6
1
/
"
or less . . . . . . 7
1
/
"
2
2
1
3
6
/
"
or less . . . . . . 7
/
"
4
4
6"
or less . . . . . . 8"
5
3
/
"
or less . . . . . . 8
1
/
"
4
4
5
1
/
"
or less . . . . . . 8
1
/
"
2
2
5
1
/
"
or less . . . . . . 8
3
/
"
4
4
5"
or less . . . . . . 9"
4
3
/
"
or less . . . . . . 9
1
/
"
4
4
1
1
4
/
"
or less . . . . . . 9
/
"
2
2
4
1
/
"
or less . . . . . . 9
3
/
"
4
4
Place the seal into the flange with
4"
or less . . . . . . 10"
3
3
/
"
or less . . . . . . Do not
the ribs facing out. Install the flange
4
use tube
with washers and hex nuts, but do not
tighten completely.
3
/
" chrome cap (provided).
4
5
Lift drain line and
Cut away wall
brace with a mending plate
If standing water is present, adjust drain
to achieve pitch (code requires 1/4" drop
per foot of drain line for proper pitch).
Seal wall according to code.
10
Install two
additional screws
Determine the drain nipple depth by
measuring the distance between the
back of the sanitary tee (or elbow) to
the front edge of the brass flange.
15
Install the gear clamp with the screw
head at the bottom, but do not tighten.
1
2
Important: Use a drain machine to
Use utility knife to cut caulk, then use
remove build-up inside pipes. Clean
a putty knife and mallet to remove the
25-35 feet deep then flush with water
bowl. Remove hanger brackets, scrape
off caulk, and clean the wall.
to remove cutting debris.
6
7
14 1/4"
Install plastic
anchor and
screw here
17" from finished floor for
standard 24" rim height ( 10 " for ADA)
Measure and mark the rough-in. Use
Hang the bowl on the bracket and
a 5/16" masonry bit to drill hole, then
check tail pipe alignment, then remove
install the hanger bracket with one
the bowl and adjust the bracket as
plastic anchor and screw.
needed.
11
12
Find the drain nipple depth on the
Cut the tube at the groove using a
cutting chart (left) and mark the
sharp utility knife to ensure a square,
specified trim length on the insert tube
flat cut. Clean burrs from the cut end
at the nearest 1/4" groove.
with emery paper.
16
17
Hang the bowl, inserting tailpipe into
Pour 5 gallons of water as rapidly as
bushing, then install anchor screws
possible into housing to ensure good
with washers. Tighten flange bolts and
flow and no leaks or standing water.
gear clamp.
3
2" side cutter blade
Clean face of existing wall flange then
install the brass flange with the clear
inspection disc. Slowly pour water into
the drain.
8
Correct
Incorrect
Re-hang and re-check bowl alignment
with the drain line. Mark anchor holes
then remove the bowl without moving
the hanger bracket.
13
Apply lubricant to the outside of the rub-
ber bushing and ribbed inside area. Insert
the tube and bushing with the arrow tab
at the top. Lube tailpipe of housing.
18
Caulk bowl to the wall. Install the
cartridge per the cartridge instruction
sheet.
The information in this document is subject to change without notice. © 2007 Sloan Valve Company. All rights reserved. 0816498, Rev 2b (07/07)
Tail pipe should
align with center
of drain line
Arrow Tab UP
Need help?
Do you have a question about the WES-4000 and is the answer not in the manual?
Questions and answers