Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Optical Systems Design OSD361
- Page 1 OPERATOR MANUAL OSD361 FIBER OPTIC CCTV TRANSMITTER MODULE...
-
Page 2: Index
OPTICAL SYSTEMS DESIGN OSD361 FIBER OPTIC CCTV TRANSMITTER MODULE Document No. 10102303 DOC ID: 10102303 PAGE 1 OSD361 OPERATOR MANUAL... -
Page 3: Table Of Contents
SITE REPAIRS ......................10 4.2.4 EXCLUSIONS ....................... 10 FIGURE 1: TYPICAL CONFIGURATIONS..................4 FIGURE 2: OSD361 CASE DIMENSIONS .................... 7 FIGURE 3: OSD361 SIDE VIEWS ......................8 TABLE 1: PRODUCTS AND OPTIONS....................4 TABLE 2: TECHNICAL SPECIFICATIONS ..................5 DOC ID: 10102303... -
Page 4: Technical Summary
The OSD361 is a small, self-contained, fiber-optic video transmitter module. Two basic configurations are available: the OSD361 is designed for use with multimode fiber and transmits at 850nm, while the OSD361L is designed for use with singlemode fiber and transmits at 1310nm. A one-way fiber-optic... -
Page 5: Typical Configuration
Link VIDEO FIGURE 1: TYPICAL CONFIGURATIONS (a) OSD361 to OSD363, (b) OSD361 to OSD383. PRODUCTS AND OPTIONS There are various options available for the OSD361 as identified in Table 1 below: TABLE 1: PRODUCTS AND OPTIONS ITEM DESCRIPTION OSD361 STANDARD FIBER OPTIC CCTV TRANSMITTER MODULE... -
Page 6: Technical Specifications
OPTICAL SYSTEMS DESIGN TECHNICAL SPECIFICATIONS Table 2 below provides Technical Specifications for the OSD361. TABLE 2: TECHNICAL SPECIFICATIONS SPECIFICATION PERFORMANCE 75Ω Input Impedance Input Level 1Vp-p Video Connector BNC Socket 2-pin socket Power Connector 10Hz to 8MHz +1/-3dB Bandwidth >50dB at –30dBm peak received optical power Weighted Signal to Noise Ratio 850 ±... -
Page 7: Installation And Operation
2 INSTALLATION AND OPERATION INTRODUCTION This section outlines the methods required to install and operate the OSD361 successfully. It should be studied carefully if damage to the equipment or poor results are to be avoided. This equipment has been fully tested prior to dispatch and is ready for immediate operation. However it is advisable to check for external transportation damage before operation. -
Page 8: Osd361 Drawings And Dimensions
OPTICAL SYSTEMS DESIGN 2.2.2 OSD361 DRAWINGS AND DIMENSIONS The OSD361 should be mounted on an even surface and secured by means of M4 or smaller screws. Figure 2 is an outer case drawing showing the required mounting dimensions. DETAIL 'A' DETAIL ‘A’... -
Page 9: Power Supply Connections
If it is necessary to clean the cable connectors use isopropyl alcohol and lint free tissue to remove contamination. 2.2.5 INDICATOR The OSD361 has one LED indicator. The indicator will be ‘green’ to indicate that power to the unit is “on”. DOC ID: 10102303 PAGE 8... -
Page 10: Maintenance
OPTICAL SYSTEMS DESIGN 3 MAINTENANCE INTRODUCTION The following section outlines the fault-finding procedure for the OSD361 modems. Please take note of the following: Personnel without appropriate training should not attempt any maintenance except that outlined below. If further maintenance is attempted you are warned that every care should be taken to ensure that... -
Page 11: Warranty
For warranty period, please call your local OSD distributor. REPAIRS Optical Systems Design reserves the right to repair or replace faulty modules/units. Please obtain a “Return Material Authorisation” (RMA) form and number before returning goods. Goods must be returned in adequate packing material to Optical Systems Design, Warriewood or its nominated authorised representative, for all repairs. - Page 12 OPTIC L Optical Systems Design Pty. Ltd. 7/1 Vuko Pl. Warriewood 2102 P.O. Box 891 Mona Vale SYSTEMS N.S.W. Australia 2103 Telephone: +61 2 9913 8540 Facsimile: +61 2 9913 8735 DESIGN Email: osdsales@osd.com.au Web Site: www.osd.com.au PTY LTD A.B.N. 83 003 020 504...