Summary of Contents for Hytera DS-6610 VPUC
- Page 1 Preface Thanks for your favor in our product. To derive optimum performance from the product, please read this manual carefully before use. This manual is applicable to the following product: DS-6610 VPUC...
- Page 2 Copyright Information Hytera is the trademark or registered trademark of Hytera Communications Corporation Limited (the Company) in PRC and/or other countries or areas. The Company retains the ownership of its trademarks and product names. All other trademarks and/or product names that may be used in this software are properties of their respective owners.
- Page 3 FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 35cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
-
Page 4: Table Of Contents
Contents Documentation Information ........................1 1. Instructions ............................2 2. Introduction ............................3 3. Product Overview ..........................4 3.1 Product Controls ..........................4 3.2 LED Indicator ..........................4 3.3 LCD Display ............................ 5 4. Basic Operations ..........................6 4.1 Turning the Gateway On/Off ......................6 4.2 Resetting the Gateway ........................ -
Page 5: Documentation Information
Documentation Information This section describes the conventions and revision history of this document. Documentation Conventions Icon Conventions Icon Description Indicates information that can help you make better use of your product. Note Indicates references that can further describe the related topics. Caution Indicates situations that could cause data loss or equipment damage. -
Page 6: Instructions
1. Instructions Read the manuals of the product carefully before use. This product shall be serviced by qualified technicians only. Use the accessories specified by the Company only, in order not to damage the product. Keep the product clean and dry for optimum performance. -
Page 7: Introduction
2. Introduction DS-6610 VPUC is a self-developed smart gateway of the Company. It can realize communications between radios with different standards and frequencies and in the same or different networks. The gateway connection is as shown in the following example. -
Page 8: Product Overview
3. Product Overview Product Controls Part Name Part Name Alarm Indicator DC Power Inlet Power Indicator Radio 1 Connector (DB15) Radio 1 Indicator Radio 2 Connector (DB15) Radio 2 Indicator Serial Port (RS232) LCD Display Ethernet Port 0 (RJ45) Function Keys (Menu/OK/Up/Down Ethernet Port 1 (RJ45) Key) Reset Key... -
Page 9: Lcd Display
LED Indicator Gateway Status Off: the gateway is off. Off: the channel is idle. Radio 1 Indicator (RADIO1) Glows orange: the gateway is transferring voice to Radio 1. Glows green: the gateway is receiving voice from Radio 1. Off: the channel is idle. Radio 2 Indicator (RADIO2) Glows orange: the gateway is transferring voice to Radio 2. -
Page 10: Basic Operations
4. Basic Operations Turning the Gateway On/Off Caution Turn off the connected radio(s) before turning off the gateway. To turn on the gateway, toggle the power switch to the “ON” position. To turn off the gateway, toggle the power switch to the “OFF” position. Resetting the Gateway To reset the gateway, long press the Reset key for five seconds. - Page 11 Step 2 Press the OK key to enter the menu, as shown below. Step 3 Press the Up/Down key to highlight “Radio1” or “Radio2”, and then press the OK key to enter the menu. Step 4 Press the OK key to select “VAD”, and then press the Up/Down key to highlight “On” or “Off”. Step 5 Press the OK key to finish.
- Page 12 Step 3 Press the Up/Down key to highlight “Radio1” or “Radio2”, and then press the OK key to enter the menu. Step 4 Press the Down key to highlight “Sensitivity”, as shown below. Step 5 Press the OK key, and then press the Up/Down key to set the sensitivity level, as shown below. The smaller value indicates higher sensitivity.
- Page 13 Step 2 Press the OK key to enter the menu, as shown below. Step 3 Press the Up/Down key to highlight “Radio1” or “Radio2”, and then press the OK key to enter the menu. Step 4 Press the Down key to highlight “Hang Time”, as shown below. Step 5 Press the OK key, and then press the Up/Down key to set the time, as shown below.
-
Page 14: Ip Settings
Step 2 Press the OK key to enter the menu, as shown below. Step 3 Press the Up/Down key to highlight “Radio1” or “Radio2”, and then press the OK key to enter the menu. Step 4 Press the Down key to highlight “Delay Time”, as shown below. Step 5 Press the OK key, and then press the Up/Down key to set the time, as shown below. - Page 15 which is with a network card. The network cards can be enabled or disabled as per actual requirements. To enable a network card, you need to set its IP address as the static IP address or a dynamic IP address. Setting the Network Card Step 1 Press the Up/Down key to highlight “IP settings”...
- Page 16 Step 1 Press the Up/Down key to highlight “IP setting” in the main menu, as shown below. Step 2 Press the OK key to enter the menu, as shown below. Step 3 Press the Up/Down key to highlight “Network0” or “Network1”, and then press the OK key to enter the menu.
- Page 17 Step 7 Press the Up/Down key to highlight “IP Address”, and then press the OK key. Then the first digit of the IP address is highlighted, as shown below. Step 8 Press the Up/Down key to change the value, and then press the OK key to confirm the value. Then the next digit will be highlighted.
-
Page 18: Language Settings
Step 3 Press the Up/Down key to highlight “Network0” or “Network1”, and then press the OK key to enter the menu. Step 4 Press the Down key to highlight “Mode”, as shown below. Step 5 Press the OK key, and then press the Up/Down key to highlight “Dhcp”, as shown below. Step 6 Press the OK key to finish. -
Page 19: Gateway Information Check
Step 2 Press the OK key to enter the menu, as shown below. Step 3 Press the OK key, and then press the Up/Down key to highlight “中文” or “Eng”, as shown below. Step 4 Press the OK key to finish. 5.3.4 Gateway Information Check You can view the gateway information, such as the software and hardware versions, network and the... - Page 20 Step 3 Press the OK key to enter the menu, as shown below. Step 4 Press the Up/Down key to view the version of software and hardware. Viewing the Network Information Step 1 Press the Down key to highlight “About” in the main menu, as shown below. Step 2 Press the OK key to enter the menu, as shown below.
- Page 21 Step 4 Press the Up/Down key to view the local IP address, subnet mask, default gateway and MAC address. Viewing the Storage Information Step 1 Press the Down key to highlight “About” in the main menu, as shown below. Step 2 Press the OK key to enter the menu, as shown below. Step 3 Press the Down key to highlight “Storage Info”, and then press the OK key to enter the menu, as shown below.
-
Page 22: Product Configuration
5. Product Configuration Before using the gateway, you need to configure it and the server. For detailed configuration, see the DS-6610 VPUC Configuration Guide in the disc. -
Page 23: Care And Cleaning
6. Care and Cleaning To guarantee optimal performance as well as a long service life of the product, please follow the tips below. Product Care Do not pierce, hit, throw, forcibly shake or scrape the product. Keep the product far away from substances that can corrode the circuit. Keep the product dry.
Need help?
Do you have a question about the DS-6610 VPUC and is the answer not in the manual?
Questions and answers