bon 12-359 Assembly Instructions

ASSEMBLY INSTRUCTIONS

Bon Tool Co. Rebar Cutter/Bender is shipped in two packages.
Please check your boxes to make sure you have all the required pieces.
Bon Tool Co. • 4430 Gibsonia Rd. • Gibsonia, P 15044 • US • www.bontool.com
1. Assemble the complete housing
unit (key #2) and the base
casting (key #3) by inserting the
Hex Head Bolts (key #014).
2. Attach the complete housing unit
and base casting to the board
(key #9) by inserting the 1/2"
carriage bolts (key #15) into the
bottom of the board. Place the
base casting and housing on top
of the board and carriage bolts
(be sure that neither edge of the
base casting is flush with the
edge of the board).
3. Next place the 1/2" flat washer
(key #16) and 1/2" nut (key #17)
on the carriage bolt and then
tighten the 1/2" nut.
4. To attach the handle clip (key #5) to
the board line up the slots on the
handle clip with the holes in the
board. Insert the 1/4" carriage bolt
(key #18) from the bottom of the
board and through the handle clip.
Then place the 1/4" flat washer
(key #19) and 1/4" wing nut (key
#20) on the carriage bolt and
tighten the 1/4" wing nut.

PARTS LIST

Ref # Key # Part # Detail
12-359 2 50-353 Housing w/ Grease Fitting
12-359 3 50-354 Base Casting
12-359 4 50-355 Back Plate
12-359 5 50-356 Handle Clip
12-359 6 50-357 Hub w/ Bushing
12-359 7 50-358 Beraring Set (48 pcs)
12-359 8 50-359 54" Steel Handle w/Grip
12-359 9 50-360 Mounting Board
12-359 10 52-661 Grease Fitting (not shown)
12-359 11 50-361 Roller Pin with Cotter Pin
12-359 12 50-362 Roller Pin w/Cotter
12-359 13 12-367 Cutter-Bushing Set (2 pcs)
12-359 14 52-479 Hex Head Bolt of Base
12-359 15 52-414 Carriage Bolt 1/2" x 2-1/2"
12-359 16 52-101 Flat Washer 1/2" on Base
12-359 17 52-199 Nut 1/2"
12-359 18 52-413 Carriage Bolt 1/4" x 2-1/4"
12-359 19 52-100 Flat Washer 1/4"
12-359 20 52-260 Wing Nut 1/4"
12-359 21 52-490 Hex Head Bolt Set for Hub
12-359 22 51-113 Handle Grip
12-359 23 52-143 Lock Washer 1/2"
12-359 24 52-666 Grease Cap
12-359 25 52-422 Hex Head Bolt M8 x 1.25 X 30mm
12-359 26 805-80375 Spacer
See Bon parts list PL12359 for complete information on all parts.
5. Insert the 54" steel
handle (key #8) into one
of the sockets on the
complete housing unit
(key #2) and your unit is
ready to use.
6. For easy storage of Bon's
Rebar Cutter/Bender place
the steel bar into a socket
on the housing unit, and
pull the handle down until
it hits the board (key #9).
Move the handle clip
(key #5) over the end of
the 54" steel handle and
tighten the handle clip
down with the 1/4" wing
nuts (key #20).
Qty/Unit
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
7
1
2
1
1
1
IS12359 05/18
PAGE 1 OF 2