Table of Contents
Advertisement
Quick Links
PROTECTION MONITORING RELAY FOR AC & DC CURRENT
PHASE CONTROL RELAY
CONFIGURATION HANDBOOK
RPL23
RPL23uC
RPL23peak
RPL23Ho
LOREME 12, rue des Potiers d'Etain Actipole BORNY - B.P. 35014 - 57071 METZ CEDEX 3
Phone 03.87.76.32.51
Contact : Commercial@Loreme.fr - Technique@Loreme.fr
Download manual at : www.loreme.fr
REV1.10 / 1.1 / 1.1 / 1.0 - 26/11/2018
E 1
Advertisement
Table of Contents
Related Manuals for Loreme RPL23
Summary of Contents for Loreme RPL23
- Page 1 RPL23 RPL23uC RPL23peak RPL23Ho LOREME 12, rue des Potiers d'Etain Actipole BORNY - B.P. 35014 - 57071 METZ CEDEX 3 Phone 03.87.76.32.51 Contact : Commercial@Loreme.fr - Technique@Loreme.fr Download manual at : www.loreme.fr REV1.10 / 1.1 / 1.1 / 1.0 - 26/11/2018...
-
Page 2: Table Of Contents
2) Recommendation of use .......................... p10 2.1) General remarks .......................... p10 2.2) Power Supply ..........................p10 2.3) Inputs / Outputs ........................... p10 WIRING ..................................p11 LOREME 12, rue des Potiers d'Etain - 57071 Metz 03.87.76.32.51 - Email: Commercial@Loreme.fr - Technique@Loreme.fr... -
Page 3: Device Presentation
TABLE OF CONTENTS Device Presentation RPL23 monitoring relay allow to detect overvoltage, under voltage, over frequency, under frequency, asymmetry, phase failure and phase order of a three-phase or a single phase low voltage or high voltage network. Characteristics: - Line voltage monitoring with or without neutral of three phase network, single phase network or continuous (DC) voltage. -
Page 4: Operating
TABLE OF CONTENTS Operating The RPL23 continuously measures L1, L2 and L3 voltages on three-phase networks or L1/N voltage on single phase networks or the continuous DC voltage between L1 & L2. Then it enable or disable its internal components, depending of configured alarms and detected faults. -
Page 5: Configuration
TABLE OF CONTENTS Configuration The RPL23 is entirely configurable in front face. Configuration access is done by pressing the top button. For each configuration rubric, a message scrolls on display. The top button (<YES>) allow to access to parameters setting of a relay or validate the corresponding function. -
Page 6: Relay #2
Displayed message: ACTIVATION DELAY Delay setting from 0 to 600 s by 0,2 s steps between 0 and 100 s and 1 s up to 600 s. LOREME 12, rue des Potiers d'Etain - 57071 Metz 03.87.76.32.51 - Email: Commercial@Loreme.fr - Technique@Loreme.fr... -
Page 7: Over Frequency Alarm
TABLE OF CONTENTS Displayed message: DEACTIVATION DELAY Delay setting from 0 to 600 s by 0,2 s steps between 0 and 100 s and 1 s up to 600 s. 5.5) Over frequency alarm Displayed message: OVERFREQUENCY CONFIG. (Y/N)? The top button allows access to configuration, the bottom button allows to move to the next rubric. -
Page 8: Rpl23Uc Features
- The activation delay, configurable from 0.1 to 600 s in 0.1 s steps from 0 to 99.9 s and 1 s steps from 100 to 600 s. - The deactivation delay, configurable from 0.1 to 600 s. LOREME 12, rue des Potiers d'Etain - 57071 Metz 03.87.76.32.51 - Email: Commercial@Loreme.fr - Technique@Loreme.fr... - Page 9 TABLE OF CONTENTS To access the configuration just press the top button. The message RELAY #1? is displayed. The top button (<YES>) provides access to its configuration, the bottom button (<NO>) jump to the relay 2 rubric. For the threshold access setting, the message displayed is: THRESHOLD? For the activation/deactivation delays access setting the messages are: ACTIVATION DELAY?
-
Page 10: Emc Consideration
1) Introduction To meet its policy concerning EMC, based on the Community directives 2014/30/EU & 2014/35/EU, the LOREME company takes into account the standards relative to this directives from the very start of the con- ception of each product. The set of tests performed on the devices, designed to work in an industrial environment, are made in accor- dance with IEC 61000-6-4 and IEC 61000-6-2 standards in order to establish the EU declaration of confor- mity. -
Page 11: Wiring
TABLE OF CONTENTS Wiring Three phases network L+, N- terminals: Power supply 20 to 265 Vac/dc or 10 to 30 Vdc. R3, R2, R1 terminal: Rest relay contact. C3, C2, C1 terminals: Common relay contact. T3, T2, T1 terminals: Work relay contact.