Download Print this page

Advertisement

Quick Links

Building instructions for the ROKE AS W 19
Thanks for the confidence into our products, which you proved with your purchase decision.
The fact, that your decision was correct will be noticeable to you surely with the view of the
supplied parts.
All supplied parts are 100 % "made in GERMANY by ROKE", and the worth of that, you´ll see
when you´re assembling and flying this model. Should emerge questions during the building
phase or later, don´t hesitate to contact us by phone within the office hours. Say us only the
model-name, number of fuselage and wing, and we can discuss and eliminate immediately
the ambiguity.
This free telephone service applies, as long as you possess the model. That's ROKE!
Safety references
Read and obey the building instructions.
Do not make changes of the intended building method and at the intended materials. If
you use other accessories or materials , make sure over their quality and efficiency.
Consider above all also the data to the position of the center of gravity, the rudder
deflections and the references to trimming and flying.
Please do not improvise anything at the model, if on the flight area somewhat does not
function correctly..
An out of control gotten flight model can be a substantial danger for you and others. A
liability insurance can release you from large problems, if despite all caution damage
happens.
Act responsibly and safetyconsciously; this begins with the building and ends after flying the
model. You not only recompence yourself thereby, but help also to receive and spread the
beautiful and instructive model flight haven.
Warning!
Remote controlled flight models are not a toy in the usual sense. Their building and enterprise
requires technical understanding, care relating to crafts and safetyconscious behavior. Errors
or carelessness when building or flying can cause damages to property or personal injuries.
Because manufacturers or salesmen do not have influence on normal building and enterprise
of the flight model, expressly these dangers are called and any responsibility is excluded!
Some words to flight physics and to the model.
Although our models should be flown actually elegantly and calmly (evenly model-faithfully),
they exhibit nevertheless substantial security reserves, which concerns the maximum stress.
For the AS W 19 the permissible load factor is 10 G. . That means, that during flight maneuvers
the complete fuselage with tail-units may charge up to its 10-times of its weight the wings
without damage.
ROKE - Modelle, Roland Kern, Rosenstrasse 2, D - 72827 Wannweil, Telefon 0049 7121 - 57 336
Bauanleitung zu ROKE AS W 19
Stand 11.10.04
Seite
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the AS W 19 and is the answer not in the manual?

Questions and answers

Summary of Contents for roke modelle AS W 19

  • Page 1 For the AS W 19 the permissible load factor is 10 G. . That means, that during flight maneuvers the complete fuselage with tail-units may charge up to its 10-times of its weight the wings without damage.
  • Page 2 Seite Bauanleitung zu ROKE AS W 19 ROKE - Modelle, Roland Kern, Rosenstraße 2, D - 72827 Wannweil, Telefon (49) 07121 - 57 336...
  • Page 3 After hardening remove the wings carefully. Glue the cross-beam-bridge and the brass-round pipe with Epoxy/glass-splinter-mixture all around at the fuselage walls firmly. Bauanleitung zu ROKE AS W 19 Seite ROKE - Modelle, Roland Kern, Rosenstrasse 2, D - 72827 Wannweil, Telefon 0049 7121 - 57 336...
  • Page 4: Aileron Linkage

    Abrade the ends of the drive steel wires well, tin these on a length of approx. 15 mm with soldering iron and radio-tin-solder. Seite Bauanleitung zu ROKE AS W 19 ROKE - Modelle, Roland Kern, Rosenstraße 2, D - 72827 Wannweil, Telefon (49) 07121 - 57 336...
  • Page 5 • Possibly not with the planking even parts of the ABS-spoiler-cover can equalized with a sandingpaper-board. Bauanleitung zu ROKE AS W 19 Seite ROKE - Modelle, Roland Kern, Rosenstrasse 2, D - 72827 Wannweil, Telefon 0049 7121 - 57 336...
  • Page 6 The photo shows our GROB G 109, is from the sense in addition, valid for the AS W 19 too! Now in the elevator a rudder horn is glued. For this you take a brass turnbuckle, or an aluminum- or GRP rudder-horn.
  • Page 7 Now cut out at front at the ledge-top a channel, approx. 5 mm wide channel, 4 cm long and centrically downward. This serves the admission of the upper aluminum-hinge-pipe. Bauanleitung zu ROKE AS W 19 Seite ROKE - Modelle, Roland Kern, Rosenstrasse 2, D - 72827 Wannweil, Telefon 0049 7121 - 57 336...
  • Page 8 Bevel longitudinal cuts at fuselage the doors according to sketch. attach doors from Seite Bauanleitung zu ROKE AS W 19 ROKE - Modelle, Roland Kern, Rosenstraße 2, D - 72827 Wannweil, Telefon (49) 07121 - 57 336...
  • Page 9 Bauanleitung zu ROKE AS W 19 Seite ROKE - Modelle, Roland Kern, Rosenstrasse 2, D - 72827 Wannweil, Telefon 0049 7121 - 57 336...
  • Page 10: Servo Installation

    2-K-Filler, easily wet sanding, then to spraying with 2-K-Acryl-Car- Laquer in the colour of your covering film. Seite Bauanleitung zu ROKE AS W 19 ROKE - Modelle, Roland Kern, Rosenstraße 2, D - 72827 Wannweil, Telefon (49) 07121 - 57 336...
  • Page 11: Safety References

    • Protect Receiver, batteries and Servos against vibrations. • do not stretch cables or bend closely! Bauanleitung zu ROKE AS W 19 Seite ROKE - Modelle, Roland Kern, Rosenstrasse 2, D - 72827 Wannweil, Telefon 0049 7121 - 57 336...
  • Page 12 With attention of these references you fulfill the most important conditions for safe flying of your model. We wish you much joy thereby. Seite Bauanleitung zu ROKE AS W 19 ROKE - Modelle, Roland Kern, Rosenstraße 2, D - 72827 Wannweil, Telefon (49) 07121 - 57 336...
  • Page 13 For emergencies not during the office hours ask for our D 2 - telephone number at international-phone-information.. Bauanleitung zu ROKE AS W 19 Seite ROKE - Modelle, Roland Kern, Rosenstrasse 2, D - 72827 Wannweil, Telefon 0049 7121 - 57 336...