Eberle Design LMA-1200-120 Operating Instructions

1.

Connect to proper source voltage

Verify source voltage before applying power. The "Pin Assignment" side label indicates the input power required for each model and indicates either Fail Safe operation
or Fail Secure operation.
MODELS 12 VDC to 24 VDC or 24 VAC
LMA-1200-LV
LMA-1200-120
LMA-1200-240
LMA-1200S-LV
LMA-1200S-120
LMA-1200S-240
OUTPUT RELAY POWER FAILURE
A
B
2. DEFLECTOMETER Indications
STATUS
0, 1, 2, 3, 4, 5, 6, 7, 8, 9
d
E
F
3.

LED Indications

STATUS POWER LED
OFF No Power
ON Normal Power
2 Hz Flash N/A
4 Hz Flash N/A
1 Flash Insufficient Line
Power
2 Flashes N/A
3 Flashes N/A
4.

Rear Panel DIP Switches and Rotary Switch

2-Position DIP Switch – Loop Frequency
SWITCH
1
2
Loop Frequency (DIPS 1 & 2) is controlled by the rear panel 2-Position DIP switch. On occasion, loops are placed in close proximity; it is necessary to select a different
frequency level for each loop to avoid loop interference (crosstalk). Four (4) frequencies are selectable, HIGH being the factory default. Press reset after changing sensitivity
setting.
8-Position DIP Switch - Detector Parameter Options
SWITCH
1
2
3
4
5
6
7
8
Extension Timing (Switches 4 & 5)
SWITCH
4
5
Output "B" Relay Configurations (Switches 6 & 7)
SWITCH
6
7
Operating Instructions
LMA-1200 "
Single Channel – Dual Output – Inductive Loop Vehicle Detectors
120 VAC
FAIL SAFE OPERATION
CALL Output
No Output
Sensitivity Meter (4, 5 & 6 = Optimum Sensitivity Setting for Loop & Lead-in Network)
OUTPUT A LED
Output OFF
Output ON
2-Second Delay Timing
0, 2, 5, or 10 Second
Extension Timing
"Real Time" Open Loop
"Real Time" Shorted Loop
"Real Time" 25% Inductance
Change
LO MEDIUM – LO
ON OFF
ON ON
ON
Sensitivity Boost
Output A – Limited Presence
2-Second Delay Timing
See "Extension Timing" Table Below (Switches 4 & 5)
See "Output B Relay Configurations" Table Below (Switches 6 & 7)
0-Seconds
0FF
0FF
Pulse On Entry
0FF
0FF
DEFLECTOMETER
" Series
240 VAC
LOOP FAILURE
CALL Output
No Output
DEFLECTOMETER
2-Second Delay Timing
0, 2, 5 or 10 Second Extension Timing
Current "Real Time" Loop Failure
OUTPUT B LED
Output OFF
Output ON
2-Second Delay Timing
0, 2, 5, or 10 Second
Extension Timing
"Real Time" Open Loop
"Real Time" Shorted Loop
"Real Time" 25% Inductance
Change
MEDIUM – HIGH
ON
OFF
OFF
No Sensitivity Boost
Output A – Infinite Presence
No 2-Second Delay Timing
Reserved
2-Seconds
ON
OFF
Pulse On Exit Presence (Duplicates Output A)
OFF
ON
Fail Safe
FAIL SECURE OPERATION
POWER FAILURE
No Output
No Output
LOOP FAULT LED
Loop Good
N/A
N/A
N/A
"Real Time" Open Loop if Outputs A & B are flashing.
"Prior" Open Loop if Outputs A & B are not flashing.
"Real Time" Shorted Loop if Outputs A & B are flashing.
"Prior" Shorted Loop if Outputs A & B are not flashing.
"Real Time" 25% Change In Inductance if Outputs A & B are flashing.
"Prior" 25% Change In Inductance if Outputs A & B are not flashing.
HIGH
OFF
OFF
5-Seconds
OFF
ON
ON
OFF
Fail Secure
LOOP FAILURE
No Output
No Output
FACTORY DEFAULT
OFF
OFF
FACTORY DEFAULT
OFF
OFF
OFF
OFF
OFF
OFF
OFF
N/A
10-Seconds
ON
ON
Fault Output
ON
ON
Rev. B – 09/18/03