Advertisement

※ INSTALLATION MANUAL
We strongly recommend reading the MANUAL before using the
product

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FHD-354 and is the answer not in the manual?

Questions and answers

Summary of Contents for HardBox FHD-354

  • Page 1 ※ INSTALLATION MANUAL We strongly recommend reading the MANUAL before using the product...
  • Page 2: Fcc Compliance

    FCC Compliance LABELLING REQUIREMENTS(Part 15, Section 15.19 (a)(3)) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operations.
  • Page 3: System Requirement

    1. Contents of FHD-354 1) FHD - 354 2) Driver Installation CD (except the way of IEEE 1394) 3) Interface cable 4) Manual 5) Slide Bar 6) AC Power Code 7) Support Beam 2. Cautions for USB 2.0 1. If the USB 2.0 product is connected to USB 1.1 Host Adapter, it will be operated as speed 1.1 (12Mbps)
  • Page 4: Installation Of Usb 2.0 Driver

    4. Driver Installation 4-1 Installation of USB 2.0 driver ※ Caution Using below 6GB hard disk can make some troubles like loss of data. We recommend you to use 6GB hard disk or greater 1. **) Caution Using below 2GB hard disk can make some troubles like loss of data, we recommend you to use 2GB hard disk or greater.
  • Page 5 4) Showing up the message "InstallShield Wizard Complete", click "Finish". Then the driver will be installed 5) Connect the AC power cable to FHD-354 and outlet then make the power "on" of FHD-354. 6) Connect FCD-354 to USB port in computer.
  • Page 6: Windows Me

    "NO. 6 the way of PARTITION and FORMAT" 2. Windows ME 1) You should connect the AC cord to the FHD-354 and turn the power(switch) on after the computer boot-up. 2) You should connect the FHD-354 to USB port on the system.
  • Page 7 Then the drive will be installed in "my computer" 3. Windows 2000 1) You should connect the AC cord to the FHD-354 and turn the power(switch) on after the computer boot-up. 2) You should connect the FHD-354 to USB port on the system.
  • Page 8: Windows Xp

    If you want to FDISK and FORMAT, you have to follow the way in "NO. 6 How to PARTITION and FORMAT" Then the drive will be installed in "my computer" 4. Windows XP 1) You should connect the AC cord to the FHD-354 and turn the power(switch) on after...
  • Page 9 2)You should connect the FHD-354 to USB port on the system. 3) Finding out the new hardware "USB Mass Storage Device", the driver will be installed automatically. 4) The drive icon will be installed in "my computer"...
  • Page 10: Checking The Driver Installation

    6. Checking the driver installation Make sure if the driver is connected successfully on the OS position. 1) Windows ME Control panel -> System -> Device manager -> Universal series Bus Controller...
  • Page 11 ) Windows 2000/XP Control panel -> System -> Hardware -> Device manager -> Universal series Bus Controller 7. How to stop using the FHD-354UFb (This is for USB interface only.) To disconnect the FHD-354Ufb from the system, please do as following instruction. 1) Windows 98 ①...
  • Page 12 ② Select the HDD model to remove it as following picture. ③ Disconnect the USB data cable from the USB port when you get the following message.
  • Page 13 2) Windows ME/2000/XP ①) Point your cursor to the “removable HDD” icon in task bar and click the left mouse button to remove it. ②) Click the above message then, the following message will appear. Now, you can safely remove the FHD-354Ufb.
  • Page 14: Installation Of Ieee 1394

    (FHD-353 can be installed only Windows 98 SE or later version) 1) Booting Windows 98 SE 2) You should connect the AC cord to the FHD-354 and turn the power(switch) on after the computer boot-up. 3) Connect the IEEE 1394 cable to the FHD- 354 and IEEE 1394 port in computer 4) Finding the message "...
  • Page 15 ※ Caution : The new hard disk which doesn't have FDISK and FORMAT, can not be recognized in "my computer" If you want to FDISK and FORMAT, you have to follow the way in "NO. 6 the way of PARTITION and FORMAT" Then the drive will be installed in "my computer"...
  • Page 16 2. Windows ME 1) Booting Windows ME 2) Connect the IEEE 1394 cable to the FHD- 354 and IEEE 1394 port in computer 3) Make sure if the hard disk icon is appearing in "my computer"...
  • Page 17 ※ Caution : The new hard disk which doesn't have FDISK and FORMAT, can not be recognized in "my computer" If you want to FDISK and FORMAT, you have to follow the way in "NO. 6 the way of PARTITION and FORMAT" Then the drive will be installed in "my computer"...
  • Page 18 1394/USB Disk ▶Control panel -> System -> Device manager --> SBP2 --> SBP2 Compliant IEEE1394 device 3. Windows 2000/XP 1) Booting Windows 2000/XP 2) Connect the IEEE 1394 cable to the FHD- 354 and IEEE 1394 port in computer 3) Make sure if the hard disk icon is appearing in "my computer"...
  • Page 19 ■ Checking the installation : After finishing the installation Control panel -> System --> Hardware -> Device manager -> Disk drive --> Oxford Semiconductor Ltd. OXFORD IDE Device IEEE 1394 SBP2 Device...
  • Page 20 2) Install the driver on the below part of offered driver CD Carry out MAC OS \ Firewire \ OS 8.6-9.X \ Korean \ Bs Crew mini Install 3) Re-booting the computer and connect FHD-354 ● MAC X version It will be recognized without any special driver 6.
  • Page 21 Again 14) If you find C:₩Windows> press " Exit" to return to Windows. 15) Separate the FHD-354 from the computer Connect the FHD-354 to USB port or IEEE 1394 port in computer again 16) The "drive word" will be created in " my computer"...
  • Page 22 7) Click the drive of "not allotted" in disk management with the right side of Mouse. 8) Choose the "making partition" among the menu. 9) After complete the "making partition magician" click "Next" 10) Checking if the "main partition(P)" is selected in kinds of partition, click "Next" 11) Type the needed capacity at "disk space"...
  • Page 23 choose management 4) Click "not allotted (ex. disk 1)" in disk management with the right side of Mouse and initialize 5) Choosing the initialized disk, click "Next" 6) Coming out "Finish changing magician and disk initialization" --> choose "Next" 7) Click the drive of "not allotted" in disk management with the right side of Mouse 8) After complete the "making partition magician"...
  • Page 24 Connect the offered USB power cable to the other USB port and then connect the power cable to FHD-354 (especially for using IBM HDD (1.0A) and HDD(Tosiba 0.7A) product ,sometimes can make lack of power.. In this case, please connect the USB power cable or power...
  • Page 25: Specification

    Specification ▶Model : FHD-354 ▶Interface : USB 2.0 / Firewire ▶Data transmission speed : 480Mbps(USB 2.0) / 800Mbps(Firewire) ▶Size : 127.2 x 75.6 x 15.5mm ▶Weight : with hard (180g) , without hard (90g) ▶Power : Interface power or adapter ▶Support OS :...

Table of Contents