Table of Contents
Related Manuals for R-tron CDMA MINI
Summary of Contents for R-tron CDMA MINI
- Page 1 CDMA MINI (RSN-CDMA-23) User’s Manual...
- Page 2 Specifications, dimensions, and other statements mentioned in this document are subject to change without notice. Questions or Comments Address: R-tron Inc. 6402 College Boulevard, Overland Park, KS 66211 Phone: +1-913-344-9977, 1-888-31R-TRON Fax: +1-913-344-9988 e-mail: info@r-tron.com...
-
Page 3: Safety Precautions
Safety Precautions Opening the CDMA equipment could result in electric shock and may cause severe injury. Connect the equipment frame ground to building ground. Operating the CDMA with antennas in very close proximity facing each other could lead to severe damage to the repeater. - Page 4 Glossary The following is a list of abbreviations and terms used in this manual. Abbreviation Definition Alternating Current Antenna Attenuator / Attenuation CDMA Code Division Multiple Access Direct Current Downlink Grounding Graphic User Interface Light Emitting Diode Phase-locked loop Power Supply Unit Radio Frequency RSSI Received Signal Strength Indication...
- Page 5 1. Introduction CDMA MINI is used to fill out areas in CDMA mobile systems, such as base station fringe areas, business and industrial building, etc. CDMA MINI receives signals from a base station, amplifies and retransmits the signals to mobile stations.
-
Page 6: Hardware Installation
3. Hardware Installation The installation procedure is as follows: • Check List of Items • Mounting • Grounding • RF Cable Connection • Power On 3.1 Check List of Items Index Items Quantity Repeater AC-DC Adaptor UTP Cross LAN Cable AC Cord Anchor Bolts CD of the User’s Manual... - Page 7 3.2 Mounting CDMA MINI is easy to mount using the assembled mounting bracket, which has 4 holes for the provided 5/16” fixing screws. Step 1 : Drill holes directly through the template. Step 2 : Install the set anchor bolts or the plastic anchor bolts on the holes.
- Page 8 Step 4 : Lean the CDMA to hang the topside of the Guide Ring on the mounting bracket, and push toward the wall to mount. Step 5 : Fix the CDMA MINI using 8 screws.
- Page 9 3.3 Grounding A rod on the left side is intended for a building ground. Connect the ground cable to the rod.
- Page 10 Step 2 : Connect a cable from a repeater’s service antenna to the Server Antenna Port. Model Max Gain Minimum required isolation (@Max Gain) CDMA MINI 50dB to 80dB ≥95dB(80dB+15dB) 3.5 Power On Step 1 : Connect the power cord.
- Page 11 This repeater follows the below set-up algorithm automatically right after POWER ON < Auto easy-setup Procedure> The below algorithm shows how to control Gain, Input / Output Power Level, Service band, ALC Level, ASD Level and path direction by using keypad display panel.
- Page 12 <Key Pad Control>...
-
Page 13: Troubleshooting
5. Troubleshooting Before contacting your service dealer, please make sure you refer to the following guide. If the CDMA MINI does not work normally after completing the following troubleshooting, please contact your local dealer or service center. Problem Cause Solution... - Page 14 7. Appendix CDMA Band Diagram...
-
Page 15: Limited Warranty
This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the United States. R-tron will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. - Page 16 Please follow the exchange procedure below. 1. Call Tech Support for troubleshooting. 2. If the device has a hardware problem, R-tron will replace it if it is within warranty. A RMA number will be issued for the return. 3. R-tron will ship the replacement and a return label will be provided.