Table of Contents
Advertisement
Models
ThermoMark
5155 / 5200 / 5255
T
o r s i o n
c
ommercial
s
l
Tandard
ifT
W
indload
Q
s
G
uick
TarT
uide
PLEASE DO NOT RETURN THIS PRODUCT
TO THE STORE
If you need assistance, please call 1-866-
569-3799 (press Option 1) and follow the
prompts to contact a customer service
representative. They will be happy to handle
any questions that you may have.
©Copyright 2018
Wayne Dalton, a division of Overhead Door Corporation
5150 /
™
T a b l e O f C o n t e n t s
Pre-Installation
Important Safety Instructions
Removing an Existing Door and Preparing the Opening
Breakdown Of Parts
Door Installation Instructions
Counterbalance Installation Instructions
Maintenance
Cleaning Your Garage Door
Painting Your Garage Door
Operation And Maintenance
Warranty
QUICK START GUIDE IMPORTANT NOTICES!
This Quick Start Guide is only meant to be used as an aid and
/ or introduction to garage door installation, and does not replace the
complete Installation Instructions and Owner's manual available on the
web at www.Wayne-Dalton.com. Wayne Dalton highly recommends
that you read and fully understand the Installation Instructions and
Owner's Manual before you attempt this installation.
To avoid possible injury, read and fully understand the enclosed
instructions carefully before installing and operating the garage door. Pay
close attention to all warnings and notes. After installation is complete,
fasten this manual near garage door for easy reference.
The complete Installation Instructions and Owner's Manual are available at no
charge from:
- Your local Wayne Dalton Sales Center, or
- Online at www.Wayne-Dalton.com, or
- By mailing to: Wayne Dalton, a division of Overhead Door Corporation,
P.O. Box 67, Mt. Hope, OH., 44660
Part Number
353364
2
2
2
3
4
7
14
14
14
14
15
REV7_05/10/2018
Advertisement
Table of Contents
Related Manuals for Wayne-Dalton ThermoMark 5255
Summary of Contents for Wayne-Dalton ThermoMark 5255
- Page 1 If you need assistance, please call 1-866- complete Installation Instructions and Owner’s manual available on the web at www.Wayne-Dalton.com. Wayne Dalton highly recommends 569-3799 (press Option 1) and follow the that you read and fully understand the Installation Instructions and prompts to contact a customer service Owner’s Manual before you attempt this installation.
-
Page 2: Important Safety Instructions
Existing Door & Prepar- 12. On electrically operated doors, pull down ropes must be removed and locks must be ing the Opening. These are available for download at www.Wayne-Dalton.com or at your removed or made inoperative in the open (unlocked) position. -
Page 3: Breakdown Of Parts
BREAKDOWN OF PARTS NOTE: The illustrations shown on this page are general representations of the door parts. Each specific door model may have unique variations. NOTE: For Item (J2), The Center Back Hang Assemblies are to be used for all doors over 11’0” door height and over 14’0”... -
Page 4: Door Installation Instructions
SEAL. DOOR INSTALLATION NOTE: Refer to the Windload Specification Sheet for the strutting schedule to determine if your bottom section requires a strut at this time. Depending on your windload option code, INSTRUCTIONS either your strut may need to be attached to the bottom section on top of the bottom corner brackets or above the bottom corner brackets. - Page 5 IF YOU HAVE TOP FIXTURE BASES AND TOP FIXTURE SLIDES: Loosely secure each of the appropriate hinges needed to be installed onto your section(s). the top fixture slide to the top fixture base using (1) 5/16” - 18 x 3/4” carriage bolt and (1) NOTE: The graduated hinges can be identified by the number stamped onto their lower hinge 5/16”...
- Page 6 IF THE BOTTOM SECTION WAS SHIMMED TO LEVEL IT, THE VERTICAL TRACK ON THE cal track against the track rollers so that the track rollers are touching the deepest part of the SHIMMED SIDE MUST BE RAISED THE HEIGHT OF THE SHIM. curved side of the track;...
-
Page 7: Counterbalance Installation Instructions
and (1) 3/8” - 16 hex nut. Repeat for other side. Remove nail that was temporally holding the Repeat the same process for the right hand side. top section in position. NOTE: This illustration shows 15” radius track with lag screws to Wood Jambs. IMPORTANT: FAILURE TO REMOVE NAIL BEFORE ATTEMPTING TO RAISE DOOR COULD Left end bracket... - Page 8 anchors (by others). This installation will require the 1/2” anchors to be secured to the build- WARNING ing and then secure the brackets to the anchors, as shown. NOTE: Pre-Drill 1/2” pilot holes into the pre-cast for the 1/2” x 3” sleeve anchors. MAXIMUM SPACING FOR DIMENSION “Y”...
- Page 9 Torsion Spring Assembly Single Spring Or Double Springs Applications, Right hand cable 1 Piece Shaft, 3-3/4” and 6” Springs drum, black IMPORTANT: ON SINGLE SPRING IMPORTANT: RIGHT AND LEFT HAND IS ALWAYS DETERMINED FROM INSIDE THE BUILDING APPLICATIONS, ONLY ONE SPRING IS LOOKING OUT.
- Page 10 Attaching Springs to Center Bracket FOR SPRINGS UP TO 3-3/4” ID AND IF YOU DON’T HAVE A COUPLER ASSEMBLY: Slide center bearing into the spring (if applicable). Align the stationary spring cone(s) with the holes in the center bracket assembly. Secure the torsion spring(s) to the center bracket assembly with (2) 3/8”...
- Page 11 6” Duplex Springs Applications NOTE: Prior to securing the center bracket to the torsion spring, ensure The bolt goes through the inner spring cone and threads into the outer spring cone. Outer torsion Bolt hole for Inner torsion Outer torsion spring assembly outer spring cone spring assembly...
- Page 12 Draw horizontal chalk line prior to WARNING winding PRIOR TO WINDING THE SPRING, ENSURE YOU’RE WINDING IN THE PROPER DIRECTION AS SHOWN BELOW. OTHERWISE THE SPRING Torsion spring FITTING MAY RELEASE FROM SPRING AND RESULT IN SEVERE OR FATAL coils INJURY.
- Page 13 Adjustments to the number of turns stated may be necessary. If door rises off floor under WARNING spring tension alone, reduce spring tension until door rests on the floor. If the door is hard to rise or drifts down on its own, add spring tension. FAILURE TO ASSEMBLE AND ATTACH REAR BACK HANGS PROPERLY NOTE: An unbalanced door such as this can cause garage door opener operation problems.
-
Page 14: Painting Your Garage Door
NOTE: If you don’t have cable keepers, then skip this step. Refer to Step 4 Attaching Cable to dirt-laden atmosphere for a period of time. Slight chalking may also occur as a result of Keepers, to determine if you have cable keepers installed. direct exposure to sunlight. -
Page 15: Limited Warranty
Overhead Door Corporation, P.O. Box 67, Mt. Hope, OH., 44660, or at www. to provide necessary maintenance, normal wear and tear, acts of God, or any Wayne-Dalton.com. For additional information on garage door/operator maintenance go to other cause beyond the reasonable control of Seller or as a result of having www.dasma.com and reference TDS 151, 167 and 179. - Page 16 Thank you for your purchase. If you need assistance, please call 1-866-569-3799 (press Option 1) and follow the prompts to contact a customer service representative. They will be happy to handle any questions that you may have. After installation is complete, leave this Installation Instructions And Owner’s Manual with the homeowner, or fasten it near garage door for easy reference.