Table of Contents
Advertisement
Quick Links
DOL 100 Water 8l/16l Box
Technical User Guide
English For other language variants of this document we refer to:
Español Para otras variantes del idioma de este documento, visite:
Français Pour les versions dans d'autres langues de ce document veuillez consulter:
http://docs.skov.com/1174
604329 • 2018-08-07
Advertisement
Table of Contents
Summary of Contents for Skov DOL 100 Water 8l
- Page 1 DOL 100 Water 8l/16l Box Technical User Guide English For other language variants of this document we refer to: Español Para otras variantes del idioma de este documento, visite: Français Pour les versions dans d'autres langues de ce document veuillez consulter: http://docs.skov.com/1174...
- Page 3 SKOV A/S would appreciate being notified thereof. • Irrespective of the above, SKOV A/S shall not accept any liability with regard to loss or damage caused or alleged to be caused by reliance on any information contained herein.
-
Page 4: Table Of Contents
DOL 100 Water 8l/16l Box 1 Product description............................ 5 2 Product survey ............................... 6 Accessories.......................... 6 3 Mounting guide............................... 7 Recommended tools ........................ 7 Assembly ............................. 8 3.2.1 DOL 100 Water box ........................ 8 3.2.2 Water level sensor ........................ 8 4 Installation guide ............................ 9 Electrical connection ........................ -
Page 5: Product Description
1 Product description The DOL 100 Water 8l/16l box is used for measuring the water level to ensure that the water pressure is in or- der. The DOL 100 will promptly show faults in the water supply, e.g. clogged or broken water pipes or lacking water supply. -
Page 6: Product Survey
DOL 100 Water 8l/16l Box 2 Product survey 130181 DOL 100 Water 81 box 130182 DOL 100 Water 16l box External I/O box for connection of water level sensors. The DOL 100 converts the signal from the water level sensor into digital sig- nals and transmits them to the controller using CAN bus communication. -
Page 7: Mounting Guide
DOL 100 Water 8l/16l Box 3 Mounting guide 3.1 Recommended tools Below follows a list of tools recommended for installation of the DOL 100. Item Description Cordless drill Screwdriver bits Utility knife Multimeter Tape measure Side cutter Needle nose pliers... -
Page 8: Assembly
DOL 100 Water 8l/16l Box 3.2 Assembly 3.2.1 DOL 100 Water box Mount DOL 100 Water box on the wall using four screws. 3.2.2 Water level sensor Drill two holes in the water pipe with a 2.4 mm drill when the water level is normal. -
Page 9: Installation Guide
EU standards that are applicable in Europe. The installation of a power supply isolator is required for each motor and power supply to facilitate voltage-free work on the electrical equipment. SKOV does not supply the power supply isolator. 4.2 Cable routing... -
Page 10: Nano Can Bus Coupler
DOL 100 Water 8l/16l Box 4.3 Nano CAN bus coupler Item Function Description Terminals Terminals to I/O modules N1 GND N2 +24V Power supply +24 VDC (max. 2.1 A) N3 CAN_H CAN high (brown CAN bus) N4 CAN_L CAN low (white CAN bus) -
Page 11: Led Indication On The Can Bus Coupler
DOL 100 Water 8l/16l Box 4.3.1 LED indication on the CAN bus coupler Item Function LED col- Description 24 V IN ON: 24 V DC power supply OK. 24 V Log ON: 24 V DC Internal OK. Green 24 V I/O ON: 24 V DC I/O fuse F1 OK. -
Page 12: Nano I/O Module Water 8L
DOL 100 Water 8l/16l Box 4.4 Nano I/O module water 8l Nano I/O module # 2 Nano I/O module # 1 Item Function Description CAN ID Jumper setting on I/O module # 1. Jumper setting on I/O module # 2. -
Page 13: Connection In Dol 100
DOL 100 Water 8l/16l Box 4.5 Connection in DOL 100 24 V DC power supply CAN bus connection, see dimensions below. CAN_H = brown CAN_L = white CAN GND = green. Strip the cable so the shield can be connected to the DOL 100 when mounting in the connection terminal. -
Page 14: Setting Up The Dol 100 In The Controller
DOL 100 Water 8l/16l Box 4.6 Setting up the DOL 100 in the controller Make sure the CAN protocol is set to CANopen. Technical | Setup | Installation | I/O Modules | CAN protocol Select number of DOL 100. The DOL 100 8I box supports up to 8 water level sensors. -
Page 15: Cable Plan
(A) Power supply to the controller two-wire cable including earthing contact. (B) Max. 400 m CAN bus communication cable between the DOL 100 Water 8l/16l box and the controller. The CAN bus cable connecting all units of the system may not exceed 400 m. -
Page 16: Circuit Diagram
DOL 100 Water 8l/16l Box 4.8 Circuit diagram 4.8.1 Water level sensor connected in series Technical User Guide... -
Page 17: Cleaning
DOL 100 Water 8l/16l Box 5 Cleaning The DOL 100 box is maintenance-free but should be kept free of litter and dirt. Clean the product with a cloth that has been wrung out almost dry in water and avoid using: •... -
Page 18: Troubleshooting Guide
DOL 100 Water 8l/16l Box 6 Troubleshooting Guide Error No light LED on the CAN bus Check the 24 V DC power supply to the DOL 100. coupler. Check that you have installed the DOL 100 water 8I/16I box and water level sensor in the controller, see section Setting up the DOL 100 in the controller [} 14]... -
Page 19: Technical Data
DOL 100 Water 8l/16l Box 7 Technical data Electrical V AC 90 – 264 Operating voltage Max. power Max. power consumption CAN bus CANopen in accordance with CiA301 and CiA401 Protocol Baud rate (fast) Max. cable length Input terminals 8 Water High KΩ... - Page 20 SKOV A/S • Hedelund 4 • Glyngøre • DK-7870 Roslev Tel. +45 72 17 55 55 • www.skov.com • E-mail: skov@skov.dk...
Need help?
Do you have a question about the DOL 100 Water 8l and is the answer not in the manual?
Questions and answers