Technical Data - Konig & Meyer 19796 Manual

SETUP
REMOVING the Tablet (11-13)
11 Loosen the three knurled pins a bit
12 Hold the tablet and LIFT UP the catch
13 Flip out the Tablet and REMOVE
If you always use the same tablet, we
recommend, recommend that the support
arm settings remain in this position.
Or remember or mark at least the
scale values.
REPEATED PLACEMENT of the
Tablet (14-16)
For previously set support arms
14 Place the tablet in the lower corner supports
15 Place the tablet into the upper catch
15 and gently press until you can hear it
15 click into place
16 Tighten the knurled pins until the tablet is
14 gently pressed into place
Then check that the Tablet is secure as
described in 10.
USAGE NOTES and FUNCTIONS
The angle, direction and format of the
tablet can be adjusted. The (securely
positioned) Tablet does not have to be
removed from the holder.
ANGLE (17-19)
The Tablet can be adjusted to
any final position by adjusting it
vertically and horizontally. To do this:
17 Hold the Tablet and loosen the wing nut somewhat
18 Pick the position (vertical / horizontal) and...
19 ...re-tighten the wing nut.
DIRECTION (20)
20 Loosen the finger screws a bit, Re-
20 position the Tablet Holder and tighten
20 the finger screws...
2a ...or position the entire support arm on
2a the stand tube in the desired direction
FORMAT (21)
The holder has a 90°-Twist Function.
This allows the Tablet to be presented in
landscape or portrait.
21 Take the holder and turn it to
19 the landscape, portrait or tilted
19 - position!
19 NOTE- Hitches within the mount limit
19 how far the holder can be turned.
DIMENSIONS (22)
The minimum and maximum size cannot be achieved due
to the Tablet's unfavorable length/width ratios.

TECHNICAL DATA

Holder, joint: Polyamid PA-6
Material Holding arm, screws, nuts, discs, springs: Steel
Screws: Steel, galvanized
Tablets Height: min. 163 mm, max. 242 mm
max. load Tablets Width: min. 102 mm, max. 189 mm
Tablets Depth: min. 5 mm, max. 11 mm
Holder W x D x H: 237/349 x 92 x 145/250 mm
Dimensions
Arm W x D x H: 40 x 232 x 58 mm
Packaging W x D x H: 254 x 104 x 150 mm
Weight net 0.58 kg, gross 0.58 kg
REMOVING the Tablet (11-13)
REPEATED PLACEMENT of the Tablet (14-16)
ANGLE & DIRECTION (17-20)
Final Position
- horizontal
- as far as it goes
FORMAT (21)
Twist (Interim Position):
Final Position
- tilted
-landscape
- not clicked into place, however it
- clicked into place
- does stay in the selected position
Interim Position:
- tilted (0-90°)
- select any position (Secure position
- by tightening the wing nut 17
Final Position
portrait
- clicked into
- place
FAULT-FINDING (F) and REPAIR (R)
F: Holder is unstable
F: R: Check the screws and tighten, if needed.
F: Tablet is not securely in place
F: R: Correct the position of the side support arms, so that the corner
F: R: supports are properly set on the Tablet without any play 3-10
F: R: Ensure that the lower support arms setting are symmetrical 5,6.
F: R: Asymmetric setting of the support arms looks bad and does not
F: R: ensure that the Tablet is securely held in place.
F: B: Do not only place the Tablet on the upper support arm, but be sure
F: R: it clicks into place 8,9.
F: B: Observe the minimum i.e maximum dimensions 22.
Final Position
- vertical
- as far as it goes
KÖNIG & MEYER GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
19796-000-55 Rev.04 03-80-087-01 1/18