ISON IS-DG102-F Quick Installation Quide

Designed for security, transportation and telco application to expand network distances.

Advertisement

Quick Links

Quick Installation Guide
FCC MARKING
This Equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
the
equipment
is
operated
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in
which
interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1)
and (2) this device must accept any interference received; including interference
that may cause undesired operation.
CE MARKING
This equipment complies with the requirements relating to electromagnetic
compatibility, EN 55022 class A for ITE, the essential protection requirement of
Council Directive 2004/108/EC on the approximation of the laws of the Member
States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be
possible that information in this document is not up-to-date. Please check with
your local distributors for the latest information. No part of this document can be
copied or reproduced in any form without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective
companies.
Copyright © 2013, All Rights Reserved.
IS-DG102-F
in
a commercial environment. This equipment
case
the
user
will
this device may not cause harmful interference,
1
interference
be
required to correct the
when

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IS-DG102-F and is the answer not in the manual?

Questions and answers

Summary of Contents for ISON IS-DG102-F

  • Page 1 IS-DG102-F Quick Installation Guide FCC MARKING This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful...
  • Page 2: Key Features

    Key Features Rugged design aluminum enclosure 103.5x32x81.5mm (LxWxD)  Supports 18V-36VAC/12V-60VDC  Supports Link Fault Pass through (LFP) fu nction  Supports switch model and converter mode.  Support SFP fiber speed 100M or 1000M dual mode  Surge protection diodes on power input. ...
  • Page 3: Power Connection

    Installation package This unit can be installed by din-rail mounted or wall-mounted. Din-rail brackets and wall-mounted bracket are included. Din Rail Bracket x 1 Wall mount bracket x 2 4 pin Terminal Block x1 Power connection This unit provides 4 pin terminal block. It can be operated using either VAC or VDC power source. The VDC power range is from 12VDC to 56VDC, and the VAC power range is from 18VAC to 36VAC.
  • Page 4: Dip Switch Function

    Dip switch function This unit is equipped with 4 pin dip-switch located on the front panel. Adjusting the dip-switch setting will change the default function of this unit. All the dip-switch settings are set to manufacturer default as OFF Table shown below is the features of these dip-switch function. You may change the dip-switch setting to your desired environment.
  • Page 5 Specification: IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX Fast Ethernet IEEE Standard IEEE 802.3ab 1000Base-T Gigabit Ethernet IEEE 802.3z 1000Base-X Gigabit Ethernet Data Processing Store and Forward IEEE 802.3x Flow Control and Back Pressure Flow Control Full wire speed conversion Auto negotiation Full/Half duplex Architecture...
  • Page 6 Power Consumption Max Power: 3 Watts 4 pin contact terminal block for power input Wire range : 0.34mm^2 to 2.5mm^2 Solid wire (AWG) : 12-24/14-22 Removable Terminal Block Stranded wire(AWG) : 12-24/14-22 Wire Strip length : 7-8mm Torque : 5lb-In/0.5Nm/0.56Nm Operating Temperature -40℃~75℃...
  • Page 7 Housing Dimension...

Table of Contents