Marcador CAFE RACER 69 mm Instruction

CAFER RACER 69mm
Thank you for purchasing speedometer, before operating the unit, please read the instruction thoroughly and retain it for the future reference.
Notice
1. DC 12V applications only.
2.For installation, please follow the steps described in manual. Any damage caused by wrong installation shall be imputed to the users.
3.To avoid the short circuit, please don't pull the wire when installing. Don't break or modify the wire terminal.
4.Do not disassemble or change any parts excluding the manual description.
5.The interior examination or maintenance should be executed by our professionals.
MARK MEANING:
NOTE You could get the installation details from the information behind the mark.
Some processes must be followed to avoid the affection caused by wrong installation.
WARNING! Some processes must be followed to avoid damages to yourself or the public.
CAUTION! Some processes must be followed to avoid the damage to the vehicle.
1-1
Accessory
1 2
Passive speed sensor X 1
LCD meter X 1
5 6 Hexagon socket
M10/ S type speed
sensor bracket X 1 screw X 2
9 10
Meter bracket X 1 Handle bar clamp X 1
13 14
M5 X P0.8 nut X 3 M6 X P1.0 nut X 1
17 18
Aluminum bush X 1
Connect terminal X 8
NOTE
Please contact the local distributor if the items you open are not the same, with the above-listed one.
INsTRUCTION
3 4 M8/ S type speed
RPM wire set X 1
sensor
7 8
D6 X 5L mm magnet X 6 2.5 mm spanner X 1
11 12
Rubber X 1 M6 X 10L screw X 1
15 16
M5 washer X 3 M6 washer X 1
Cortesia de www.marcadoresdemoto.com
2-1
Wiring installation instructions
LIGHT ON FLASH
Dark brown
PRESS THE PRESS THE
BUTTON ONE BUTTON 3
TIME SECONDS
bracket X 1
Main switch wiring reference:
"+" Color
YAMAHA
Brown
HONDA Brown
SUZUKI Black
SYM Black
NOTE
The color listed above may differ depending
on the model.
NOTE
When connecting the power wiring, please
follow the instruction. If you connect the red & brown
wiring in parallel will cause the meter work improperly.
NOTE
When connecting the power wiring, please follow the instruction. If you connect the red & brown wiring in parallel will cause the meter work improperly.
The RPM wire installation
Please check the polarity of your ignition coil, before you connect the RPM sensor type B there. An incorrect installation can lead to a defect of the meter or destroy
the electrical system of your vehicle.
Transistor Ignition: If your vehicle has a transistor ignition system, connect the tach to the negative pole of the ignition coil.
CDI ignition: If your vehicle has a CDI ignition system, connect the speed sensor to the positive pole of the ignition coil.
MOTO / SCOOTER
Cortesia de www.marcadoresdemoto.com
Purple Neutral (-)
─
Orange Left-turn signal(+12V)
─
Blue Right turn signal(+12V)
─
Yellow High beam (+12V)
─
Gray Warning lamp(-)
─
LCD meter (Accessory 1 )
Red / Postive pole (Connect
to the battery DC 12V)
Speed sensor wiring
RPM Signal wire
─
Please choose either Type A or Type B RPM wire
according to the need and then follow the
instruction below to install at the proper position.
RPM wire set
(Accessory 3)
"-" Color
Black
Black
Green
Ignition coil positive
Green
Flywheel
Ignition
pulse
Tachometer
S type speed sensor bracket instruction
Loose the screw on the caliper
Install the S type bracket on the caliper.
Please adjust the bracket to the proper angle
and then screw it up. Please make sure the
disc screw could pass the hole on the bracket
for you to install the sensor into the same hole
for catching the speed signal.
Brown / "+"Wire connect key
on DC 12V main power switch
Black / Ground wire connect
to the vehicle body or the
engine (It must be a good
ground)
Digital speed signal
sensor (Accessory 2)
NOTE
Speed Sensor is
a "Hall Sensor ".
Magnet (Accessory 8)
Spark plug wire
Coil
Spark plug
Spark cap
pick up
Install the speed sensor.
Adjusting the distance between the sensor
and screw to get the best speed signal.
Please make sure the distance is under 2 mm
to get the best signal.
wh035ba002