Advertisement
Quick Links
57-1543
DODGE / CHRYSLER
2009-10 Challenger SE
2006-10 Charger SE / Charger SXT
2005-10 300 Touring
2005-10 300 Limited
2005-08 Magnum SXT
V6-3.5L
PARTS LIST:
Description
A
Hose Clamp #44
B
Hose; 3.0"ID X 1.75"L
C
Grommet
D
Intake Tube
E
Hose Clamp #48
F
Bolt; 6mm F/H/A
G Saddle Bracket
H
Washer, conical, nylon, black
I
Washer; 1/4"ID X 5/8"OD, Flat
NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE
MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.
TO START:
1. Turn off the ignition and disconnect the negative
battery cable.
NOTE: Disconnecting the negative battery
cable erases pre-programmed electronic
memories. Write down all memory settings be-
fore disconnecting the negative battery cable.
Some radios will require an anti-theft code to
be entered after the battery is reconnected. The
anti-theft code is typically supplied with your
owner's manual. In the event your vehicles'
anti-theft code cannot be recovered, contact an
authorized dealership to obtain your vehicles
anti-theft code.
2. Unlock the red locking tab on the air tempera-
ture sensor electrical connection, then depress the
locking lever and pull apart the temperature sensor
electrical connection
3. Loosen the hose clamp that secures the intake
tube to the throttle body and pull the intake tube off
the throttle body.
A
B
A
C
Qty.
Part #
2
08560
J
Nut; 6mm Nylock
1
08190
K
Washer, 10mm Wave
2
08064
L
Bolt; 10mm Hex
1
087155
M Bracket
1
08601
N
Vent
1
08376
O Hose; 1/2"id X 7"L
1
078855
P
Hose Clamp #56
1
08180
Q Hose; 3.5"ID X 2"L
1
08275
R
Edge Trim #44
4. Disconnect the crankcase vent hose from the
valve cover port as shown.
5. Loosen and remove the airbox mounting bolt as
shown.
6. Lift the complete intake and air filter assembly to
remove it from the vehicle.
NOTE: K&N Engineering, Inc., recommends that
customers do not discard factory air intake.
7. Assembly the tube-mounting bracket and saddle
clamp as shown with the provided hardware.
D
Q
P
E
F
C
G
H
N
O
I
M
J
K
L
1
07553
1
08175
1
07702
1
010096
1
08065
1
08159
2
08620
1
08630
1
102486
R
W
P
V
T
U
S
V
T U
S
Heat Shield
T
Bolt; 6mm B/H/A
U
Fender Washer
V
Washer 1"x.300"x.100",
W Filter Adapter, #190
X
Hose Clamp #104
Y
Air Filter
8. Using the provided hardware, install the tube-
mounting bracket onto the engine at the threaded
hole in the cylinder head as shown.
9. Install the provided edge trim onto the heat
shield as shown.
NOTE: Some trimming of the edge trim may be
necessary.
10. Install the air filter adapter onto the heat shield
with the provided hardware as shown.
NOTE: Be sure to use the rubber gaskets pro-
vided.
Y
X
TOOLS NEEDED:
Flat Blade Screwdriver
Ratchet
Extension
10mm Socket
17mm Socket
4mm Allen
1
074035
2
07730
2
08160
2
21685
1
08806
1
08697
1
RF-1048
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for K&N 57-1543
- Page 1 57-1543 DODGE / CHRYSLER 2009-10 Challenger SE 2006-10 Charger SE / Charger SXT 2005-10 300 Touring 2005-10 300 Limited 2005-08 Magnum SXT TOOLS NEEDED: V6-3.5L Flat Blade Screwdriver Ratchet Extension 10mm Socket 17mm Socket PARTS LIST: 4mm Allen Description Qty.
- Page 2 INSTALLATION INSTRUCTIONS Continued 21. Install the provided silicone vent hose onto the 11. Install the K&N air filter onto the filter adapter ® 16. Install 2nd supplied grommet into the filter end valve cover vent and onto the elbow into the K&N as shown.
Need help?
Do you have a question about the 57-1543 and is the answer not in the manual?
Questions and answers