Advertisement
Quick Links
INSTRUCTION MANUAL
MULTI PURPOSE DRINKS FRIDGE
This manual contains important information including safety and installation instructions of the
appliances. Please read it carefully a n d k e e p h a n d y for easy reference.
Note: Not to be used for preservation of fresh foods, this is a drinks refrigerator
CONTENTS
IMPORTANT SAFETY INFORMATION........................................................................................P.1
STRUCTURE AND
INSTALLATION
ACCESSORY INSTALLATION BEFORE OPERATING...............................................................P.5
OPERATING THE REFRIGERATOR............................................................................................P.6
CARE AND MAINTENANCE........................................................................................................P.9
TROUBLESHOOTING..................................................................................................................P.10
REVERSE THE DOOR SWING................................................................................................P.12
YC150W YC150B YC100W
YC100B YC150D YC100D
DRAWING...........................................................................P.2
Advertisement
Summary of Contents for Schmik YC150B
- Page 1 INSTRUCTION MANUAL MULTI PURPOSE DRINKS FRIDGE YC150W YC150B YC100W YC100B YC150D YC100D This manual contains important information including safety and installation instructions of the appliances. Please read it carefully a n d k e e p h a n d y for easy reference.
- Page 2 IMPORTANT SAFETY INFORMATION To avoid the risk of fire, electrical shock, or injury when using the appliance, follow these basic precautions: • The fridge is intended to be used exclusively for the storage of beverages only. Plug into a grounded 3-pin outlet, do not remove grounding pin, do not use an adapter, and do •...
- Page 3 *Remember more depth is needed if you are plugging electrical cord in at rear, app 65mm *Note, some laws require power point to be accessible, most times power point is located away from the fridge cavity. YC150W, YC150B, YC150D building into cabinetry under bench...
- Page 4 ACCESSORY INSTALLATION BEFORE OPERATING UNPACKING AND CLEANING THE DRINKS FRIDGE ● Remove the exterior and interior packing materials. ● Let the appliance stand upright for approximately 2 hours before connecting it to the power source, which helps to reduce the possibility of a cooling-system malfunction from handling during transportation.
- Page 5 WINE BOTTLE SHELF STORAGE (Models JC430W and JC430D) ● Wine and beer shelves are ball bearing pull-out sliding type, they are fixed in fridge but can be moved up/down so you can allow room for larger diameter bottles etc. Wine shelves also have the unique patented ‘Saddle Shift Shelving”...
- Page 6 Keypad introduction *Note Dual zone models YC100D and YC150D have 2 x controllers, each controller controls 1 section, Left is Top Zone and Right is Bottom Zone. Explanation of the buttons Normal operation Buttons Press for 1 second Press for 3 second Turn up the parameters list；...
-
Page 7: Power Failure
CARE AND MAINTENANCE CLEANING THE DRINKS FRIDGE ● Turn off the power, unplug the appliance, and remove all items including shelves. ● Wipe the inside surfaces with a sponge and baking soda solution. The solution should be about 2 table spoons of baking soda to 1 liter of warm water. ●... - Page 8 TROUBLESHOOTING If you feel the appliance is out of order, follow these instructions to try to see if you can solve the problem simply by yourself before calling for service. POSSIBLE CAUSE / MEASURE PROBLEM The Drinks Fridge does not operate Not plugged in.
Need help?
Do you have a question about the YC150B and is the answer not in the manual?
Questions and answers
My dual zone fridge is displaying 22.6 and 23.2 degrees. When I try and set the temp I can adjust it but when i press set it just goes back to 22.6 and 23.2
If the Schmik YC150B dual zone fridge is not accepting temperature settings and displays 22.6 and 23.2 degrees, try the following steps:
1. Press the “SET” button for 3 seconds.
2. The current set temperature will appear.
3. Use the “UP” or “DOWN” buttons to adjust the temperature in 0.1°C increments.
4. Press “SET” again to confirm.
If the unit still does not accept new settings or the display does not change, the temperature probe may be faulty. A faulty probe can prevent accurate readings and may stop the unit from adjusting temperatures correctly. Check if the display shows “HH” or “LL” or if there is a continuous buzzing sound, which also indicates a probe fault.
If the issue persists, the unit may need service.
This answer is automatically generated
@Mr. Anderson Thanks I checked the above and there are no alarms but I’ll organise a service