The –XX at the end of the product's part number (see label on the product) defines the product's variant. For the IO Board CIG1-IOC01-0A-01-00 Normally, we only have this 00 version IO board and future we will support more products. Central-I - Hardware Manual -IO Board CiG1-IOC01-0A-01-00 V1.1.docx Page 5...
The IO Board includes a built-in protection to avoid damage in case of inversed polarity at the input power. The IO Board uses logic power of 9-36Vdc to reduce load of main power supply. Central-I - Hardware Manual -IO Board CiG1-IOC01-0A-01-00 V1.1.docx Page 6...
Page 7
Filter Capacitors are also connected with the main input logic power to provide the external 24v output power ( can be seen in J2 Input IO Power) for the external use. Figure 3: Filter Capacitors Central-I - Hardware Manual -IO Board CiG1-IOC01-0A-01-00 V1.1.docx Page 7...
This input IO power can provide 24V, up to 8A IO power for external use. Filter Capacitors are also connected with the main power to provide power for the I/O ports. (can be seen in J1 Input Logic Power Port) Central-I - Hardware Manual -IO Board CiG1-IOC01-0A-01-00 V1.1.docx Page 8...
Cable connector P/N: IPD1-06-D-K Crimp P/N: CC79L-2630-01-L Other options are possible; please, consult with the manufacturer. Name Type Description Vin_24V_IO_RTN PWR-OUT 24V IO Power return Vin_24V_IO PWR-OUT 24V IO Power for external use Central-I - Hardware Manual -IO Board CiG1-IOC01-0A-01-00 V1.1.docx Page 9...
Page 10
Discrete, isolated, input 1 (NPN or PNP, depending on OC_Input1 connection of the common pin of this group) Analog_Input_return_1 Analog output 1 return (internally connected to GND Central-I - Hardware Manual -IO Board CiG1-IOC01-0A-01-00 V1.1.docx Page 10...
Page 11
The electrical interfaces of analog input 2 in port J4, analog input3 in port J5 and analog ▪ input4 in port J8 all are identical to those of analog input 1. ▪ The analog inputs are -12v to +12v, 12 bits. Central-I - Hardware Manual -IO Board CiG1-IOC01-0A-01-00 V1.1.docx Page 11...
Page 12
▪ The software provides parameters to control the analog input reading, as follows: ❖ Filter. ❖ Offset. ❖ Dead band. ❖ Gain Central-I - Hardware Manual -IO Board CiG1-IOC01-0A-01-00 V1.1.docx Page 12...
Page 13
▪ can be wired to interface PNP devices. However, within a group, all interfaces should be the same, as they are based on the connection of the group common pin Central-I - Hardware Manual -IO Board CiG1-IOC01-0A-01-00 V1.1.docx Page 13...
Discrete, isolated, input 6 (NPN or PNP, depending on OC_Input6 connection of the common pin of this group) OC_Input_5-8_Common Common power pin for discrete, isolated, inputs 5 to 8 Analog_Input_2 Analog input 2, ±12v, 12 bit Central-I - Hardware Manual -IO Board CiG1-IOC01-0A-01-00 V1.1.docx Page 14...
Page 15
Discrete, isolated, input 5 (NPN or PNP, depending on OC_Input5 connection of the common pin of this group) Analog_Input_return_2 Analog output 2 return (internally connected to GND Central-I - Hardware Manual -IO Board CiG1-IOC01-0A-01-00 V1.1.docx Page 15...
Discrete, isolated, input 10 (NPN or PNP, depending on OC_Input10 connection of the common pin of this group) OC_Input_9-12_Common Common power pin for discrete, isolated, inputs 9 to 12 Central-I - Hardware Manual -IO Board CiG1-IOC01-0A-01-00 V1.1.docx Page 16...
Page 17
Discrete, isolated, input 9 (NPN or PNP, depending on OC_Input9 connection of the common pin of this group) Analog_Input_return_3 Analog output 3 return (internally connected to GND Central-I - Hardware Manual -IO Board CiG1-IOC01-0A-01-00 V1.1.docx Page 17...
Discrete, isolated, output 2 (programmable sink or OC_Output2 source) OC_Output_1-4_Common_Power PWR-IN Common power pin for discrete, isolated, outputs 1 to 4 PWR-OUT Power Ground 5V_SW2 PWR-OUT 5V Power Supply for other components Central-I - Hardware Manual -IO Board CiG1-IOC01-0A-01-00 V1.1.docx Page 18...
Page 19
(up to 300mA) or as a current sinking output (up to 500mA). Common power is shared by all 4 outputs. ▪ ▪ Common power can go up to 45 volts. Yet, typical usage should be limited by 36v. Central-I - Hardware Manual -IO Board CiG1-IOC01-0A-01-00 V1.1.docx Page 19...
Discrete, isolated, input 16 (NPN or PNP, depending on OC_Input16 connection of the common pin of this group) OC_Input_13-16_Common Common power pin for discrete, isolated, inputs 13 to 16 Central-I - Hardware Manual -IO Board CiG1-IOC01-0A-01-00 V1.1.docx Page 21...
Page 22
Discrete, isolated, input 13 (NPN or PNP, depending on OC_Input13 connection of the common pin of this group) Analog_Input_return_4 Analog output 4 return (internally connected to GND Central-I - Hardware Manual -IO Board CiG1-IOC01-0A-01-00 V1.1.docx Page 22...
Discrete, isolated, output 6 (programmable sink or OC_Output6 source) OC_Output_5-8_Common_Power PWR-IN Common power pin for discrete, isolated, outputs 5 to 8 PWR-OUT Power Ground 5V_SW2 PWR-OUT 5V Power Supply for other components Central-I - Hardware Manual -IO Board CiG1-IOC01-0A-01-00 V1.1.docx Page 23...
Page 24
Discrete, isolated, output 7 (programmable sink or OC_Output7 source) Discrete, isolated, output 5 (programmable sink or OC_Output5 source) Common power return pin for discrete, isolated, outputs OC_Output_5-8_Common_Return PWR-IN 5 to 8 Central-I - Hardware Manual -IO Board CiG1-IOC01-0A-01-00 V1.1.docx Page 24...
(The details of the board can be referred to in the hardware manual of CIGI-COM01-1A- 02-01) 3. The RJ45 connector is between the two connectors to communicate with the master controller CIG1-MAS product variants via the Central-I Protocol Central-I - Hardware Manual -IO Board CiG1-IOC01-0A-01-00 V1.1.docx Page 25...