Download Print this page

Tetra ColorFusion Bubbling LED Start Here

Aquarium kits

Advertisement

Quick Links

4
Hood & Filter Placement and Start Up
A. Install Filter so it lines up beneath the
Hood cutout.
B. Plug AC adapter into power outlet.
Make a Drip Loop for safety.
C. Press switch to cycle auto changing color fusion
LEDs. Press again to pause at desired color.
Press and hold to turn off.
Install Filter
A
Troubleshooting Guidelines
If the LED lights fall into the water: This LED light is waterproof. Simply remove the LED Light from
the water and attach it to the frame using the LED frame clip.
LIMITED ONE YEAR WARRANTY: Within one year from the date of original purchase (shown on
your receipt), we will repair or replace, at our option, any of the following components which are deemed
defective in workmanship or materials. This includes: LED Lights, Hood, Bubble Tube or Air Pump.
Please return the suspect component(s) together with proof of purchase (your receipt):
Call (800) 526-0650 for return authorization and shipping address.
Damage or injuries resulting from negligence or misuse are not covered by this warranty. Incidental or
consequential damages are specifically excluded.*
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
*Because some states do not allow the exclusion of incidental or consequential damages, this exclusion may not apply to you.
Distributed by United Pet Group, Inc. (UPG)
3001 Commerce St., Blacksburg, VA 24060
®Regestered Trademark and ™Trademark of
United Pet Group, Inc. or one of its affiliates.
©2014 UPG
IMPORTANT:
Always unplug the LED
Light
C
Lights before inspecting
Switch
or beginning any
maintenance procedures.
Drip Loop
B
(for safety)
02/14
P/N R08307 Rev. A
Start Here - Tetra
®
Quick Setup Guide
1
Parts Check
A
Waterproof
Frame Clip
Tetra
®
ColorFusion
LED Light
Low Voltage
Transformer
Hood
B
Feeding
Hole
Bubble
C
Tube
Replacement Parts List
KEY ITEM #
DESCRIPTION
A
R07016
6˝ Tetra
ColorFusion LED Light (5g Kit)
®
A
R07014
8˝ Tetra
ColorFusion Light (10g Kit)
®
B
R03942
16˝ x 9˝ Hood (5g Kit)
B
R03943
20˝ x 10˝ Hood (10g Kit)
C
R07017
Bubble Tube with Check-Valve
D
R07015
Air Pump with Air Line Tubing
Questions or Missing Parts Call Customer Service (800) 526-0650
M-F 7:30 a.m. - 5:30 p.m. (Eastern Time)
© 2014 United Pet Group, Inc.
ColorFusion Aquarium Kits
for Kit Sizes: 5 and 10 gallons
LED
Cord Routing
Clips (2)
Light Switch
D
Air Pump
Air Line
Tubing
Check
Valve
QUANTITY
www.tetra-fish.com
1
1
1
1
1
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the ColorFusion Bubbling LED and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Tetra ColorFusion Bubbling LED

  • Page 1 Start Here - Tetra ColorFusion Aquarium Kits ® Hood & Filter Placement and Start Up Quick Setup Guide for Kit Sizes: 5 and 10 gallons A. Install Filter so it lines up beneath the Parts Check Hood cutout. Waterproof B. Plug AC adapter into power outlet.
  • Page 2: Important Safeguards

    IMPORTANT SAFEGUARDS Install LED Light A. Clip Waterproof LED Light into the front WARNING: To guard against injury, basic safety precautions should be observed, including the following: C. Plug in and make a drip loop READ AND FOLLOW ALL of the aquarium frame. for safety.