1. Manuals
  2. Brands
  3. ETAS Manuals
  4. Other
  5. ES5338.1
  6. User manual

ETAS ES5338.1 User Manual

Carrier board for wheel speed sensor simulation, psi5, direct current output 6 sockets, wheel speed sensor simulation, psi5, direct current output piggyback
Hide thumbs
Table of Contents

Advertisement

Quick Links

ES5338.1 Carrier Board for Wheel Speed Sensor Simula-
tion, PSI5, Direct Current Output (6 Sockets)
PB5338CURR.1-A Wheel Speed Sensor Simulation, PSI5,
Direct Current Output Piggyback
User's Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ES5338.1 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for ETAS ES5338.1

  • Page 1 ES5338.1 Carrier Board for Wheel Speed Sensor Simula- tion, PSI5, Direct Current Output (6 Sockets) PB5338CURR.1-A Wheel Speed Sensor Simulation, PSI5, Direct Current Output Piggyback User’s Guide...
  • Page 2 The data in this document may not be altered or amended without special noti- fication from ETAS GmbH. ETAS GmbH undertakes no further obligation in rela- tion to this document. The software described in it can only be used if the customer is in possession of a general license agreement or single license.

  • Page 3: Table Of Contents

    Scope of Supply ..........17 Design of the ES5338.1 Carrier Board ......18 Fuses .
  • Page 4 7 ETAS Contact Addresses ........

  • Page 5: Introduction

    ETAS Introduction Introduction This User’s Guide contains the description of the ES5338.1 Carrier Board for Cur- rent Output Piggyback PB5338CURR.1-A. The ES5338.1 Carrier Board can be populated with up to six modules of the PB5338CURR.1-A Wheel Speed Sensor Simulation Piggyback. This combination allows simulating up to six sensors.

  • Page 6: Properties

    1.1.1 Properties of the ES5338.1 Carrier Board The ES5338.1 Carrier Board is a plug-in card for a LABCAR HiL system for use in the ES5300.1-A Housing and in the ES5300.1-B Housing. The ES5338.1 Carrier Board can be populated with up to six PB5338CURR.1-A Piggybacks.

  • Page 7: Block Diagram Of Es5338.1 Carrier Board

    Block Diagram of ES5338.1 Carrier Board The block diagram in Fig. 1-1 on page 7 shows the essential functional units of the ES5338.1 Carrier Board. Fig. 1-1 Block diagram of ES5338.1 Carrier Board ES5338.1 Carrier Board for Wheel Speed Sensor Simulation - User’s Guide...

  • Page 8: Basic Safety Notices

    1.2.2 General Safety Information Please observe the Product Safety Notices ("ETAS Safety Notice") and the follow- ing safety notices to avoid health issues or damage to the device. Note The User's Guide must be read prior to the startup of the product! ETAS GmbH does not assume any liability for damages resulting from improper handling, unintended use or non-observance of the safety precautions.

  • Page 9: Intended Use

    ETAS Introduction 1.2.4 Intended Use The ES5338.1 Carrier Board is a plug-in card for the ES5300.1-A Housing and the ES5300.1-B Housing. The ES5338.1 Carrier Board can accommodate up to six PB5338CURR.1-A Piggybacks. The ES5338.1 Carrier Board consists of the following: •...
  • Page 10 Wait at least three minutes before removing the add-on card. Approved Cables The signal lines must not exceed a maximum length of 3 m. ES5338.1 Carrier Board for Wheel Speed Sensor Simulation - User’s Guide...
  • Page 11 To avoid damages to the hardware from electrostatic discharge, please observe the following precautionary measures: CAUTION! Some components of the ES5338.1 Carrier Board can be damaged or destroyed by electrostatic discharges. Leave the plug-in card and the Piggybacks in the transport packaging until their installation.
  • Page 12 Connecting/Disconnecting Devices To avoid injuries and hardware damages, please observe the following precau- tionary measures: • Do not apply any voltages to the connections of the ES5338.1 Carrier Board that do not correspond to the specifications of the respective con- nection.

  • Page 13: Identifications On The Product

    37. 1.3.1 CE Mark With the CE mark attached to the product or its packaging, ETAS confirms that the product corresponds to the product-specific, applicable European Directives. The CE Declaration of Conformity for the product is available upon request.

  • Page 14: Kc Marking

    The user is obligated to separately collect old devices and provide them to the WEEE return system for recycling. The WEEE Directive applies to all ETAS devices, but not to external cables or bat- teries. Additional information about the recycling program of ETAS GmbH is available from the ETAS sales and service locations (see "ETAS Contact Addresses"...

  • Page 15: About This Manual

    This section provides a description of the different connections of the ES5338.1 Carrier Board. • "Technical Data and Standards" on page 37 This chapter contains the technical data of the ES5338.1 Carrier Board for Current Output Piggyback PB5338CURR.1-A. It also contains standards met.
  • Page 16 Content-based highlights and newly intro- and arithmetic data types is not duced terms are placed in italics. possible. Important notes for the user are presented as follows: Note Important note for the user. ES5338.1 Carrier Board for Wheel Speed Sensor Simulation - User’s Guide...

  • Page 17: Design, Installation And Fuses

    • "Installation in the ES5300.1-A Housing and the ES5300.1-B Housing" on page 25 CAUTION! Some components of the ES5338.1 Carrier Board can be damaged or destroyed by electrostatic discharges. Leave the plug-in card in its transport packaging until its installation.

  • Page 18: Design Of The Es5338.1 Carrier Board

    Design, Installation and Fuses ETAS Design of the ES5338.1 Carrier Board The front plate and plug side of the ES5338.1 Carrier Board are shown in Fig. 2-1.. Fig. 2-1 Front plate and plug side of the ES5338.1 Carrier Board The backplane connector "CO200" forms the communication interface to the ES5300.1-A Housing and to the ES5300.1-B Housing.
  • Page 19 ETAS Design, Installation and Fuses The ES5338.1 Carrier Board is delivered without PB5338CURR.1-A Piggyback. The ES5338.1 Carrier Board is shown in Figure 1-2 in its delivery state. Fig. 2-2 Longitudinal view of ES5338.1 Carrier Board without piggybacks Figure 1-3 shows the PB5338CURR.1-A Piggyback.
  • Page 20 The ES5338.1 Carrier Board is designed exclusively for the ETAS PB5338CURR.1-A Piggyback. The installation of non-supported boards can lead to damages of the ES5338.1 Carrier Board, the ES5300.1-A Housing or ES5300.1-B Housing and/or the non-supported board. ES5338.1 Carrier Board for Wheel Speed Sensor Simulation - User’s Guide...

  • Page 21: Fuses

    The voltages of the backplane of the ES5300.1-A Housing or the ES5300.1-B Housing are protected with fuses on the ES5338.1 Carrier Board. In case of a fuse defect, we recommend sending the board to ETAS for further testing. For this purpose, the device should be sent to ETAS (see "ETAS Contact Addresses"...

  • Page 22: Specification Of Fuses

    Design, Installation and Fuses ETAS Fig. 2-5 on page 22 shows the position of the fuses on the ES5338.1 Carrier Board. FU 202 FU 203 FU 201 Fig. 2-5 Position of fuses on the ES5338.1 Carrier Board 2.3.1 Specification of Fuses:...

  • Page 23: Assembly Of Piggyback

    This chapter describes how the PB5338CURR.1-A Wheel Speed Sensor Simula- tion Piggyback are installed on an ES5338.1 Carrier Board. CAUTION! Some components of the ES5338.1 Carrier Board can be damaged or destroyed by electrostatic discharges. Leave the plug-in card in its transport packaging until its installation.
  • Page 24 Design, Installation and Fuses ETAS Assembly of the PB5338CURR.1-A Piggyback on the ES5338.1 Carrier Board The assembly of a PB5338CURR.1-A Piggyback on the ES5338.1 Carrier Board is described below. Proceed analogously with the assembly of additional PB5338CURR.1-A Piggy- backs 1. Ensure that ESD-compliant conditions exist at your workplace.

  • Page 25: Installation In The Es5300.1-A Housing And The Es5300.1-B Housing

    Installation in the ES5300.1-A Housing and the ES5300.1-B Housing This chapter describes how the ES5338.1 Carrier Board is installed in the ES5300.1-A Housing or in the ES5300.1-B Housing. CAUTION! Do not install any boards while the ES5300.1-A Housing or ES5300.1-B Housing is switched on!
  • Page 26 If correctly installed, the ES5338.1 Carrier Board occupies only one slot of the ES5300.1-A Housing or the ES5300.1-B Housing. If neighboring boards or cover slots collide with the ES5338.1 Carrier Board, then the combination of PB5338CURR.1-A and ES5338.1 Carrier Board is not correctly installed.

  • Page 27: Simulated Sensor Signals

    Simulated Sensor Signals This chapter describes the sensor signals that can be generated with the ES5338.1 Carrier Board. The ES5338.1 Carrier Board can simulate one sensor of the following types for each populated PB5338CURR.1-A Piggyback: • "DF10 and DF11s" on page 29 •...
  • Page 28 The simulated sensor signals Curr_0_n, Curr_0_p ... Curr_5_n, Curr_5_p are out- put as digital output signals at the "CO601" plug (see "Pin assignment of signal channels on CO601" on page 35). ES5338.1 Carrier Board for Wheel Speed Sensor Simulation - User’s Guide...

  • Page 29: Signal Shapes

    ETAS Simulated Sensor Signals Signal Shapes This chapter describes the wheel speed sensor signals generated by the ES5338.1 Carrier Board. 3.3.1 DF10 and DF11s The sensor signals of type DF10 and DF11s are digital rectangular current pulses whose frequency is proportional to the wheel speed from the vehicle model.
  • Page 30 RTIO. Tab. 3-1 Action of PWM current pulses of a simulated sensor of type DF11i (see also Fig. 3-2 on page 31) ES5338.1 Carrier Board for Wheel Speed Sensor Simulation - User’s Guide...

  • Page 31: Vda

    9 data bits for each segment of the pick-up wheel. They contain information about the following parameters: • Wheel speed • Tooth voids • Travel direction • Standstill detection • Air gap reserve error detection • Installation position error detection ES5338.1 Carrier Board for Wheel Speed Sensor Simulation - User’s Guide...

  • Page 32: Psi5

    LABCAR-RTC User's Guide. 3.3.4 PSI5 The ES5338.1 Carrier Board can generate signals following PSI5 (Peripheral Sen- sor Interface 5), version V 1.3 and V 2.1. They can be used, e.g. to simulate pres- sure sensors. A description for configuring the PSI5 signals is located in the LABCAR-RTC User's Guide.

  • Page 33: Connections And Plug Connections

    ETAS Connections and Plug Connections Connections and Plug Connections This section provides a description of the different connections of the ES5338.1 Carrier Board. • "Backplane Connector CO200" on page 33 • "VG 96 Plug CO601" on page 35 WARNING! Fire hazard! Use only approved cables for creating cable assemblies (e.g.
  • Page 34 GBLI_TX_n_0 GBLI_TX_p_0 GBLI_RX_n_0 GBLI_RX_p_0 M_LVDS_n_7 M_LVDS_p_7 BN_5 BN_4 12-shield GBLI_TX_n_1 GBLI_TX_p_1 GBLI_RX_n_1 GBLI_RX_p_1 M_LVDS_n_6 M_LVDS_p_6 SPI_CS_B_n SPI_CS_A_n 11-shield GBLI_TX_n_2 GBLI_TX_p_2 GBLI_RX_n_2 GBLI_RX_p_2 M_LVDS_n_5 M_LVDS_p_5 SPI_MOSI SPI_CLK 10-shield GBLI_TX_n_3 GBLI_TX_p_3 GBLI_RX_n_3 GBLI_RX_p_3 M_LVDS_n_4 M_LVDS_p_4 PCIE_WAKEn SPI_MISO 9-shield GBLI_PRESENT_n GEO_ADDR_4 PCIE_REFCLK_n PCIE_REFCLK_p M_LVDS_n_3 M_LVDS_p_3 n.c.

  • Page 35: Vg 96 Plug Co601

    Pin assignment of signal channels on CO601 Type: DIN 41612, Type C Counterplug: DIN41612 plug connector without crimp contacts (order no. Harting 09030963214); crimp contacts (order no. Harting 09020008484) ES5338.1 Carrier Board for Wheel Speed Sensor Simulation - User’s Guide...
  • Page 36 The function of the reference pin is given only if noise immunity is observed during the design of the grounding/cabling concept. (This means, for example, signal flow with low impedance, defined reference potentials, low transition resistances, shielded design, no crosstalk). ES5338.1 Carrier Board for Wheel Speed Sensor Simulation - User’s Guide...

  • Page 37: Technical Data And Standards

    ETAS Technical Data and Standards Technical Data and Standards This chapter contains the technical data of the ES5338.1 Carrier Board for Cur- rent Output Piggyback PB5338CURR.1-A. It also contains standards met. Technical Data Current Outputs Output current 0 to 120 mA Accuracy ±0.5 mA at 40 mA...

  • Page 38: Standards Met

    Should that be the case, the operator may be requested to institute reasonable measures. Note The signal lines may not exceed a maximum length of 3 m! ES5338.1 Carrier Board for Wheel Speed Sensor Simulation - User’s Guide...

  • Page 39: Ordering Data

    Wheel Speed Sensor Simulation. Board PSI5, Direct Current Output (6 Sock- ets) PB5338CURR.1-A Wheel Speed Sen- PB5338CURR.1-A F-00K-110-052 sor Simulation, PSI5, Direct Current Output Piggyback Scope of Supply Quantity ES5338.1 Carrier Board ES5338.1 Carrier Board for Wheel Speed Sensor Simulation - User’s Guide...
  • Page 40 Ordering Data ETAS ES5338.1 Carrier Board for Wheel Speed Sensor Simulation - User’s Guide...

  • Page 41: Etas Contact Addresses

    For details of your local sales office as well as your local technical support team and product hotlines, take a look at the ETAS website: ETAS subsidiaries WWW: www.etas.com/en/contact.php ETAS technical support WWW: www.etas.com/en/hotlines.php ES5338.1 Carrier Board for Wheel Speed Sensor Simulation - User’s Guide...
  • Page 42 ETAS Contact Addresses ETAS ES5338.1 Carrier Board for Wheel Speed Sensor Simulation - User’s Guide...

  • Page 43: Index

    Declarable Substances 14 Design 17 Devices Plug connections 33 Connecting 8 Product return 14 Properties 17 Electrical safety 10 ETAS Contact Addresses 41 Qualification, required 8 Fuses 17 Recycling 14 ES5338.1 Carrier Board for Wheel Speed Sensor Simulation - User’s Guide...
  • Page 44 VDA 31 Signal 29 Signal lines 38 Specification of fuses 22 Standards 37 Storage conditions 37 Technical data 37 Waste Electrical and Electronic Equip- ment 14 WEEE return system 14 ES5338.1 Carrier Board for Wheel Speed Sensor Simulation - User’s Guide...

This manual is also suitable for:

Pb5338curr.1-a

Table of Contents

Save PDF