Page 2
PREFACE / QUALITY PHILOSOPHY You have decided in favour of a SPARTHERM fireplace insert accessory - thank you very much for your confidence in our company. In a world of excess and mass production, our company stands for the values expressed by our owner, Gerhard Manfred Rokossa: "High technical quality combined with contemporary design and service to the satisfaction of our customers, so they will recommend us to others".
CONTENTS 1. General information 9. Closed-loop control characteristics 1.1 Information on installation 1.2 Accessories 10. App 1.3 Functional description of S-Thermatik NEO 11. Notes for stoves: 2. Safety notes 12. Guide 3. Menu structure and display 3.1 Menu structure 13. General warranty conditions 3.2 Main menu...
To maintain your control system, keep the door contact clean and ensure With appliances that circulate water, if the recirculating pump is to be controlled by the S-Thermatik NEO, at least two PT 1000 sensors should that the combustion air channel remains clean and unobstructed. From time to time, check here whether the permanent magnet is attached to the bot- be ordered at the same time.
Mains connection Actuator The basic configuration of the S-Thermatik NEO combustion control system consists of the control unit, the display, a flue gas temperature sensor, an actuator motor and a door contact switch. It is only suitable for fire areas that burn split logs.
2. SAFETY NOTES 3. MENU STRUCTURE AND DISPLAY 3.1 MENU STRUCTURE • The S-Thermatik NEO combustion control may only be used in combina- tion with a wood-fired fireplace insert. • Only fire areas which are ordered with this combustion control system...
3.2 MAIN MENU 3.3 GENERAL OPERATION OF THE DISPLAY CANCEL Brightness SAVE CHANGES Adding fresh fuel USER MENU CURRENT TEMP Auto brightness AIR SLIDER Menu Home EXHAUST TEMP. POWER STAGES There is a BACK button at the top left of each menu window to enable you Menu Home to go back one step in the operating process.
4. STATISTICS 5. USER MENU Statistics CANCEL The menu layout is broadly self-explanatory. Here is a sample image for LAST COMBUSTION general operation: Highest temperature Duration Sound CANCEL Highest temperature Duration USER MENU Highest temperature Duration Signal transmitter active Sound 1 Sound 2 This is where you will find the statistics for the last 99 combustion pro- Home...
Page 9
This pushbutton must be pressed otherwise the changes will not be made. it can be connected to the S-Thermatik NEO using a special cable. The displays on the housing of the S-USI II can be shown on the display unit of SESAM: Whenever this function is assigned to a relay in the Service menu, the NEO.
6. SELF-TEST: To return to Automatic mode, slide the control knob to the left again and save it. To check the control system and its function, it can help to run a self-test. CAUTION: Operation of the fire area in Manual mode is at the user's This provides an indication as to whether all components in the control own risk! During a burnup, the air control lever must never be closed system are OK.
Type the password key for service menu 7. POWER FAILURE The S-Thermatik NEO is equipped with a special function. Whenever there is a power failure, the air slider automatically moves into a safe position (about 50-60%). In this position, the fire area cannot overheat, but it can continue being operated manually.
• Following a cold start, if a temperature of at least 50°C is not reached 9. CLOSED-LOOP CONTROL within 10 minutes of the door being opened, the air slider is closed and the control system reports "No ignition". CHARACTERISTICS • Whenever the fireplace insert threatens to overheat, this is This section explains a few of the closed-loop algorithms that govern opera- displayed and the air slider is restricted in order to reduce the tion of the control system.
10. APP For the S-Thermatik NEO there is an app for devices with an Android or an The data link only functions using Bluetooth. The module is integrated in IOS operating system. This app goes by the name of S-Thermatik NEO and the control system.
This should always be set to Auto. Stoves are usually supplied without a display The user obtains information Only then can the S-Thermatik NEO work properly. about the current status of the control system from a function monitoring LED that is usually installed in the bottom flap of the stove.
• No power between actuator motor and actuat- The air control lever only moves to the right and ing lever, driver pin (star) has wandered out of The S-Thermatik NEO burnup controller detects the most significant errors stays there. position.
Spartherm Feuerungstechnik GmbH offers a 24-month guarantee in respect 13. GENERAL WARRANTY CONDITIONS of the sliding door mechanism, operating components such as handles, set- ting levers, shock absorbers, electrical and electronic components such as 13.1 AREA OF APPLICATION fans, rotational speed controllers, the manufacturer's original spare parts, all items purchased as additional extras and all safety appliances.
13.8 SPARE PARTS • The gaskets and seals: Reductions in sealing strength due to seal hard- ening as a result of thermal loading. • The glass ceramics: Soiling, due to soot or other burnt-on combustion Only the manufacturer's own components, or replacement parts recom- materials and visual deterioration due to thermal loading.
Wireless systems directive 2014/53/EU - (RED) Spartherm Feuerungstechnik GmbH Maschweg 38 / 49324 Melle, Germany hereby declare that the products listed below comply with the above EU Directives: Product type: Combustion control Model: S-Thermatik NEO Melle, 11.01.2017 Gerhard Manfred Rokossa, CEO GB 18...
Page 20
SPARTH ERM DIE WELTMARKE FÜR IHR WOHNZIMMER The Global brand for your living room | La référence mondiale pour votre salon | Il marchio mondiale per il vostro soggiorno La marca mundial para su salón | Het merk van wereldformaat voor uw woonkamer | Światowa marka do Państwa salonu Торговая...
Need help?
Do you have a question about the S-Thermatik NEO and is the answer not in the manual?
Questions and answers