Advertisement

Quick Links

version:1.0
User Manual
Blood Pressure Monitor
Arm Type
Please do read the user manual carefully and thoroughtly so as to ensure
the safe usage of this product, and keep the manual well for further
reference in case you have problems.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BM-201 and is the answer not in the manual?

Questions and answers

Summary of Contents for Dretec BM-201

  • Page 1 version:1.0 User Manual Blood Pressure Monitor Arm Type Please do read the user manual carefully and thoroughtly so as to ensure the safe usage of this product, and keep the manual well for further reference in case you have problems.
  • Page 2: Table Of Contents

    CATALOGUE CATALOGUE Table of Contents INTRODUCTION ........................2 General Description Indications for Use Safety Information LCD Display Signal Monitor Components Measurement Principle BEFORE YOU START ........................7 Installing and Replacing the Batteries Tie the Cuff MEASUREMENT........................8 Start the Measurement INFORMATION FOR USER.
  • Page 3: Introduction

    General Description This device is intended for adult use only. Readings taken by the BM-201 are equivalent to those obtained by a This device is intended for no-invasive measuring and monitoring of arterial blood pressure. trained observer using the cuff and stethoscope auscultation method.
  • Page 4: Lcd Display Signal

    INTRODUCTION INTRODUCTION Monitor Components LCD display signal CUFF Component list of pressure measuring AIR HOSE system 1 Cuff 2 Air pipe 3 PCBA 4 Pump 5 Valve AIR CONNECTOR PLUG START/STOP BUTTON BATTERY COMPARTMENT LCD DISPLAY SYMBOL DESCRIPTION EXPLANATION Systolic blood pressure High blood pressure Diastolic blood pressure Low blood pressure Pulse in beats per minute...
  • Page 6: Measurement Principle

    INTRODUCTION BEFORE YOU START Tie the cuff Measurement Principle 1. Tie the cuff on your upper arm, This product uses the Oscillometric Measuring method to detect then position the tube off-center blood pressure. Before every measurement, the unit establishes a toward the inner side of arm in “zero pressure”...
  • Page 7: Measurement

    MEASUREMENT INFORMATION FOR USER Start the Measurement Tips for Measurement Measurements may be inaccurate if taken in the following When the monitor is off, circumstances. press the “START/STOP” button to turn on the monitor, and it will finish the whole measurement .
  • Page 9: About Blood Pressure

    INFORMATION FOR USER ABOUT BLOOD PRESSURE Maintenance What are systolic pressure and diastolic pressure? In order to get the best performance, please follow the When ventricles contract and pump blood Systolic Diastolic instructions below. out of the heart, the blood pressure reaches blood entering blood discharging vein...
  • Page 11: Why Does My Blood Pressure Fluctuate Throughout The Day

    ABOUT BLOOD PRESSURE TROUBLESHOOTING This section includes a list of error messages and frequently Why does my blood pressure asked questions for problems you may encounter with your blood fluctuate throughout the pressure monitor. If the products not operating as you think it day? should, check here before arranging for service.
  • Page 12: Specifications

    SPECIFICATIONS CONTACT INFORMATION Contact Information Battery powered mode: Power supply 6VDC 4×AAA batteries Display mode Digital LCD V.A.60mm×40.5mm Measurement mode Oscillographic testing mode Rated cuff pressure: 0mmHg~300mmHg Measurement range Measurement pressure: 40mmHg-230mmHg Pulse value: (40-199) beat/minute Pressure: Accuracy 5℃-40℃within±3mmHg Pulse value:±5% Normal working Temperature:5℃...
  • Page 13: Emc Guidance

    EMC GUIDANCE EMC Guidance 1) This equipment needs to be installed and put into service in accordance with the information provided in the user manual; 2) Wireless communications equipment such as wireless home network devices, mobile phones, cordless telephones and their base stations, walkie-talkies can affect this equipment and should be kept at least a distance d=3,3m away from the equipment.

Table of Contents