1. Manuals
  2. Brands
  3. Direct Supply Manuals
  4. Heat Pump
  5. E7822
  6. Owner's manual

Direct Supply E7822 Owner's Manual

Packaged terminal air conditioner/heat pump
Hide thumbs
Table of Contents

Advertisement

Quick Links

Direct Supply
®
PACKAGED TERMINAL AIR
CONDITIONER/HEAT PUMP
Owner's Manual
Please keep and refer to this Owner's Manual.
Thank you for purchasing a Direct Supply
Packaged Terminal Air Conditioner/Heat Pump from Direct Supply Equipment
®
& Furnishings
. Please read this entire guide carefully and keep it for future reference. This guide will provide you with
®
instructions, warnings, warranty information and other important information about your Packaged Terminal Air Conditioner/
Heat Pump. Share this information with your housekeeping, nursing and maintenance staff to help ensure the Packaged
Terminal Air Conditioner/Heat Pump is cared for properly.
1-800-634-7328 DirectSupply.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the E7822 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Direct Supply E7822

  • Page 1 Owner’s Manual Please keep and refer to this Owner’s Manual. Thank you for purchasing a Direct Supply Packaged Terminal Air Conditioner/Heat Pump from Direct Supply Equipment ® & Furnishings . Please read this entire guide carefully and keep it for future reference. This guide will provide you with ®...

  • Page 2: Table Of Contents

    • Children should be supervised to ensure they do not play with the appliance. • If the supply cord is damaged, it must be immediately replaced. Contact Direct Supply Equipment & Furnishings and do not use the product until the cord has been replaced.

  • Page 3: Safety Precautions

    Safety Precautions • • WARNING: Plug in power plug properly. CAUTION: When the air filter is to be removed, Otherwise, it may cause electric shock or fire due do not touch the metal parts of the unit. It may to excess heat generation. cause an injury.

  • Page 4: Important Safety Instructions

    Please refer to the section “Operation of Current Device” for details. In the event that the power supply cord is damaged, it cannot be repaired. It must be replaced. Do not use a product with a damaged power cord. Contact Direct Supply Equipment & Furnishings to order a replacement. •...
  • Page 5 • The power supply must be replaced if it fails reset when either the TEST button is pushed or it cannot be reset. A new one can be obtained from Direct Supply Equipment & Furnishings. • If power supply cord is damaged, it cannot be repaired. It MUST be replaced by one obtained from Direct Supply Equipment &...

  • Page 6: Product Features

    Standard on all models. FAN SPEED MODE Direct Supply units feature three fan speeds and AUTO mode for the user to select from CONSTANT FAN MODE Fan can be set to run continuously in both heating and cooling mode via DIP switch settings on the...

  • Page 7: Ptac Specifications

    PTAC Specifications Resistance Heat Models DS Part Number #E7822 #E7830 #E7823 #E7831 #E7824 #E7832 #E7825 #E7833 #G1249 PERFORMANCE DATA: Cooling Btu 7300/7100 7300 9200/9000 9200 12000/11800 12000 14700/14500 14700 14700/14500 Cooling Watts 613/596 814/796 1121/1102 1120 1547/1526 1547 1547/1526 Energy Efficiency Ratio, EER 11.9...

  • Page 8: Air Conditioner Features

    Air Conditioner Features This unit has many features. The user must be familiar with these features in order to properly service the unit. Compressor Restart Delay This feature extends the overall life of compressor by preventing the short-cycling of the air conditioner.

  • Page 9: Control Panel Operation

    Control Panel Operation The control panel keypad will look like the following: UP/DOWN BUTTONS (+/-) • Push the UP or DOWN button to increase or decrease the set temperature of the unit in cooling or heating mode. The temperature can be set by increments of 1°F or 1°C. The temperature setting appears in the display.

  • Page 10: Dip Switch Configurations

    Dip Switch Configurations Removing The Front Panel • Dip switch controls are located behind front panel Dip Switches through an opening below the control panel. To access, remove front panel. (See Fig.1) • Dip switches are accessible without opening the control box.
  • Page 11 Electric Heat Only (for heat pump unit only) Switch S1 • This setting is typically used for Emergency Heating. Wall Thermostat Enable Switch S3 • A wired wall thermostat can be connected to the unit. If it is, this dip switch must be moved to the Wall Thermostat Enable Position before the wall thermostat will begin control.

  • Page 12: Wall Thermostat Terminal

    Wall Thermostat Terminal IMPORTANT: Only trained, qualified personnel should access the electrical panel on the unit and install electrical accessories. Please contact your local electrical contractor, dealer or distributor for assistance. Thermostat Wire Routing Proper Wire Routing Beneath Unit Thermostat wire is not supplied with the PTAC. Recommended wire gauge is 18- to 20-gauge Remove th solid thermostat wire.
  • Page 13 Notes • Use terminal 4-way for heat pump connection only. • The PTAC has a built-in 3-minute compressor protection time. If the compressor protection time on the thermostat is set for less than 3 minutes, the default PTAC 3-minute compressor protection time will take precedence.

  • Page 14: Installation

    Installation Dimension of air conditioner How To Install The Unit 42inch/1067mm • CAUTION: There are sharp edges that can cause 42inch/1067mm serious cuts. When lifting the air conditioner, it is HEAVY. Use two people to lift. 16inch/ • If installing into an existing sleeve, you should 408mm 16inch/ measure the wall sleeve dimensions prior to...

  • Page 15: Installation

    Vent control lever Unit Installation Vent control lever (cont.) • • Rotate the vent control lever to either open or close CAUTION: Do not put obstacles the vent door. (See Fig.6) around air-inlet or inside of air-outlet of the unit, such as window curtain, Fig.6 etc.

  • Page 16: Care & Cleaning

    Care & Cleaning 2 Air filters • Removing Air Filter Front Panel and Case 2 Air filters Pull up • Turn off unit and disconnect power supply. To clean, use water and a mild detergent. DO NOT Pull up use bleach or abrasive cleaners. Some commercial cleaners may damage the plastic parts.

  • Page 17: Troubleshooting

    Troubleshooting Possible Causes Solutions Unit Does Not Start • Unit may have become unplugged • Check that plug is plugged securely in wall receptacle. • Fuse may have blown NOTE: Plug has a test/reset button on it. Make sure the plug has not •...

  • Page 18: Accessories

    Accessories #C9779 Direct Supply PTAC Foldable #E7838 Sub Base Assembly for Direct Supply Wall Sleeve PTAC Units, 265V, 30-Amp Units #E7839 Sub Base Assembly for Direct Supply #C9780 Direct Supply PTAC Aluminum Grill PTAC Units, 265V, 20-Amp Units #C9781 Direct Supply PTAC Extruded...

  • Page 19: Limited Warranty

    Customer Service Limited Warranty We, Direct Supply Manufacturing, Inc., offer to you, as the original purchaser, a warranty for this Direct Supply PTAC. Our warranty applies for the limited warranty period stated below. If any product or product part listed below has an original defect in material or workmanship during the applicable limited warranty period, we will replace it at our cost.
  • Page 20 Distributed by Direct Supply Manufacturing, Inc. 6635 N Industrial Road, Milwaukee, WI 53223. © 2015-2018 Direct Supply Manufacturing, Inc. All Rights Reserved. Direct Supply , and all associated logos are the registered ® trademarks of Direct Supply, Inc., used under license.

This manual is also suitable for:

E7831E7830E7823E7824E7825E7832 ... Show all

Table of Contents

Save PDF