Sanyo KMHS1272 Installation Instructions Manual
Inverter split system air conditioner
Hide thumbs
Also See for KMHS1272:
- Technical & service manual (88 pages) ,
- Installation instructions manual (27 pages) ,
- Brochure & specs (2 pages)
Table of Contents
Advertisement
- Inverter Split System Air Conditioner -
Contents
Please Read Before Starting .................................. 2
1.
GENERAL .......................................................... 3
2.
INSTALLATION SITE SELECTION ................... 4
3.
HOW TO INSTALL THE INDOOR UNIT .............. 6
4.
5.
POSITION ......................................................... 17
6.
ADDRESS SWITCH .......................................... 18
7.
DEVICE.............................................................. 19
8.
INSTALLATION CHECK SHEET ...................... 19
85264189998000 © SANYO 2006
INSTALLATION INSTRUCTIONS
This air conditioner uses the new refrigerant R410A.
Page
SANYO FISHER COMPANY
A DIVISION OF SANYO NORTH AMERICA CORPORATION
21605 Plummer Street
Chatsworth, CA 91311 U.S.A.
Model Combinations
Combine indoor and outdoor units only as listed
below.
Indoor Unit
KMHS0772
KMHS0972
KMHS1272
KMHS1872
KMHS2472
Power Source:
60 Hz, single-phase, 230 / 208 VAC
Combinations of indoor and outdoor units
Connect indoor and outdoor units only in the combi-
nations listed in the catalog or installation manual.
CAUTION
Connecting any other model may result in
operation failure and system damage.
Be sure to read the yellow instruction sheet
attached to the outdoor unit for models using the
new refrigerant R410A.
NOTE
The illustrations are based on the typical appearance of
a standard model. Consequently, the shape may differ
from that of the air conditioner that you are installing.
For Indoor Unit
COOL / DRY/ HEAT Model
Outdoor Unit
CMH1972
CMH2472
CMH3172
In Canada
SANYO Canada Inc.
300 Applewood Crescent, Concord
Ontario, L4K 5C7, Canada
Advertisement
Table of Contents
Related Manuals for Sanyo KMHS1272
Summary of Contents for Sanyo KMHS1272
-
Page 1: Table Of Contents
The illustrations are based on the typical appearance of a standard model. Consequently, the shape may differ from that of the air conditioner that you are installing. SANYO FISHER COMPANY A DIVISION OF SANYO NORTH AMERICA CORPORATION 21605 Plummer Street Chatsworth, CA 91311 U.S.A. For Indoor Unit... -
Page 2: Important
Get a partner to help, and bend your knees when lifting to reduce strain on your back. Sharp edges or thin alu- minum fins on the air conditioner can cut your fingers. When Installing… …In a Ceiling or Wall Make sure the ceiling/wall is strong enough to hold the unit’s weight. -
Page 3: General
Narrow Tube Model Outer Dia. KMHS0772 1/4" (6.35 mm) 0.0314" (0.8 mm) KMHS0972 1/4" (6.35 mm) 0.0314" (0.8 mm) KMHS1272 1/4" (6.35 mm) 0.0314" (0.8 mm) KMHS1872 1/4" (6.35 mm) 0.0314" (0.8 mm) KMHS2472 1/4" (6.35 mm) 0.0314" (0.8 mm) 6. -
Page 4: Additional Materials Required For Installation
WARNING and the possibility of fire, do not place obstacles, enclosures and grilles in front of or surrounding the air conditioner in a way that may block air flow. AVOID: direct sunlight. nearby heat sources that may affect performance of the unit. -
Page 5: Embedding The Tubing And Wiring
Install the indoor unit more than 3.3' (1 m) away from any antenna or power lines or connecting wires used for tele- vision, radio, telephone, security system, or intercom. Electrical noise from any of these sources may affect operation. install in a sturdy manner to avoid increased operating noise. -
Page 6: How To Install The Indoor Unit
Set screw only for transportation Fig. 6 Rear panel Fig. 7 Left tubing Left-rear tubing Fig. 8 (KMHS0772, KMHS0972, KMHS1272) 2-3/4" (70 mm) Fig. 9a (KMHS1872, KMHS2472) 2-3/8" (60 mm) Fig. 9b marks Right-rear tubing (recommended) -
Page 7: Install The Rear Panel On The Wall
Indoor side Fig. 10 PVC pipe (Locally purchased) Cut at slight angle Fig. 11 INSIDE Wall Plastic cover (Locally purchased) Fig. 12 (KMHS0772, KMHS0972, KMHS1272) Fig. 13a (KMHS1872, KMHS2472) Fig. 13b Fig. 14 Outdoor side OUTSIDE PVC pipe Slight angle... -
Page 8: Remove The Grille To Install The Indoor Unit
3-4. Remove the Grille to Install the Indoor Unit 3-4-1. Indoor unit types (KMHS0772, KMHS0972, KMHS1272) Basically, these models can be installed and wired without removing the grille. If access to any internal part is needed, follow the steps as given below. - Page 9 3-4-2. Indoor unit types (KMHS1872, KMHS2472) Basically, these models can be installed and wired with- out removing the grille. If access to any internal part is needed, follow the steps as given below. How to remove the grille (1) Grasp both ends of the air intake grille, and remove it by opening towards the front and pulling towards you.
-
Page 10: Shape The Indoor Side Tubing
3-5. Shape the Indoor Side Tubing (1) Arrangement of tubing by directions a) Right or left tubing Cut out the corner of the right/left frame with a hacksaw or the like. (Figs. 20 and 21) b) Right-rear or left-rear tubing In this case, the corner of the frame need not be cut. -
Page 11: Wiring Instructions For Inter-Unit Connections
3-7. Wiring Instructions for Inter-unit Connections (1) Insert the inter-unit wiring (according to local codes) into the through-the-wall PVC pipe. Run the wiring toward the indoor side allowing approx. 10" (25 cm) to extend from the wall face. (Fig. 24) (2) Grasp both ends of the air intake grille, and remove it by opening towards the front and pulling towards you. - Page 12 Loose wiring may cause the WARNING terminal to overheat or result in unit malfunction. A fire hazard may also exist. There- fore, be sure all wiring is tightly connected. When connecting each power wire to the corresponding terminal, follow the instructions “How to connect wiring to the terminal”...
-
Page 13: Mounting
3-8. Mounting (1) To install the indoor unit, mount the indoor unit onto the 2 tabs on the upper part of the rear plate. (2) Hold down the air discharge outlet and press the lower part of the indoor unit until it clicks to securely fasten to the 2 tabs on the lower part of the rear plate. - Page 14 I Left-side tubing (1) Lead the tubing and drain hose through the wall, allowing sufficient length for connection. Then bend the tubing using a tube bender to make the attach- ment. (Fig. 38) (2) Switch the drain hose and drain cap. Switching drain hose and drain cap (a) Locate the drain hose and the drain cap.
-
Page 15: Drain Hose
To unmount indoor unit Press the 2 marks on the lower part of the indoor unit and unlatch the tabs. Then lift the indoor unit and unmount. (Fig. 42) 3-9. Drain Hose a) The drain hose should be slanted downward to the outdoors. -
Page 16: How To Test Run The Air Conditioner
4. How to Test Run the Air Conditioner After turning on power to the air conditioner, use the remote controller and follow the steps below to conduct the test run. (1) Set the remote controller in Test Run mode. (Fig. 59a) a) Press and hold the ION button. -
Page 17: Remote Control Unit Installation Position
In direct sunlight Behind a curtain or other place where it is covered More than 26' (8 m) away from the air conditioner In the path of the air conditioner’s airstream Where it may become extremely hot or cold... -
Page 18: Address Switch
6-1. Address Setting of the Remote Control Unit The address can be set in order to prevent interference between remote controllers when two Sanyo indoor units are installed near each other. The address is normally set to “A.” To set a different address, it is necessary to change the address on the second remote controller. -
Page 19: Connecting A Home Automation Device
7. Connecting a Home Automation device The HA (white) 4P terminal is located on the indoor unit PCB. If a HA device will be used, connect it to this terminal. 8. Installation Check Sheet The strength of the installation location is sufficient to support the A/C weight. The indoor and outdoor units are installed level and vertically.