Contents Product Description and Structure........01 Operating instruction ............02 Grinding Cautions............02 Use step diagram...............02 Application step..............03 Grinding time suggestions..........04 Operating Instructions of oily material......05 Instructions of air overload protector........06 How to clean up the grinding groove........07 How to replace the blade............08 replace carbon brushes How to...
Product Description and Structure Product Description This grinder is a machine that grinds a variety of food,medicines and other food into powder,and the diameter of each powder particle ranges from 8.47um to 36.2um.When put the materials into the grinding groove, the materials will be ground into the powder instantly by the operation of blade and tip.
Operating instruction Grinding Cautions It is not suitable for grinding something which is wet, fresh, soft ,strong toughness such as meat, fruits, vegetables, etc. 1. To grinder something more easily when the material is high-hardness, big in size, or has the strong fiber, you need to cut them into small pieces, for example, to grind the notoginseng better, you need to cut them into small pieces.
Page 5
Application step: Step 1:Open the top lid of grinder,opening way (clockwise -off, counter-clockwise -open). Step 2:Put the dried material(Like soybean) into the grinding groove. If it is not dry, please dry it first. Step 3:Close the top lid of grinder tightly. Step 4:Turn on power,open time switch.(If there is no time switch,you need to master the time by yourself,the time of grinding common grains is about 30 seconds, the hard ones is about 1-3 minutes )
300g material into grinding groove,this is the best for grinding. 1.Soybeans has shell, so it is better to grind for about one minute. Grind for 30 seconds and stop to stir,after 10 seconds,grind for 30 seconds again.
Operating Instructions of oily material 1.One third of capacity of grinding groove is the best amount for grinding.Putting too much crushed stuff is not good because powder needs space.If there is too much crushed stuff in grinding groove,the powder will become uneven easily because the more crushed stuff, the more oil,and then the powder will become uneven,such as walnut、...
Instructions of air overload protector When the voltage is unstable, or grinding blades are jammed in grinding groove,it will happen that air overload protector pop up and cut off the power supply. If this situation happens, turn off the power and check the voltage. Meanwhile, check the grinding groove.After troubleshooting, press the air overload protector, continues to grind.This device is similar to voltage control equipment installed in the outdoor,which plays a role in control in...
How to clean up the grinding groove You can clean up the grinding groove of grinder with brush first,and then clean it with dry cloth.After using blades for a long time ,you can remove them and clean them with water.(The blades of new grinder must be very tight,you need to use for a long time,then blades can be removed) ...
How to replace the blade Blade replacement method Use the screwdriver to fix the blade, preventing it from rotation. Then rotate counterclockwise with the help of tool, loosen the hex screws on the blade, open the blade to use. Blade cleaning method Do not clean with water after removal of the blade, wipe it with a dry rag.
Operation Precautions 1. In order to ensure user's personal safety, the power cord must be grounded (the grinder should be connected to the three plug wiring board ), remember that the 150g grinder has two head plug wire. 2. Recommend grinding capacity:one third of the crushed tank. the minimum grinding should be higher than the blade ,Do not exceed two-thirds of the crushed tank.
Common fault causes and remedies Malfunction Common fault causes Remedies(Cut off the power as a precondition) 1. Bad power supply or plug is 1. Repair or replacement loose power plug 1.The machine does not operate after 2. Switch contact problem 2.
Product List: COLDENWALL Grain Grinder 150g hand-held type 300g hand-held type 300g swing type 400g swing type Asin:B00PQHLF38 Asin:B00JMEBB2Q Asin:B00JMEOGM8 Asin:B00JMEWLOI 500g swing type 700g swing type 800g swing type 1000g swing type Asin:B01FSH1AUI Asin:B01FTEW3QK Asin:B073GR1VHF Asin:B00JMFURD4 1500g swing type...
Page 16
CGOLDENWALL is a manufacturer specialized in the production of stainless steel high-speed grinder ,we will provide you the Professional Technical Support and Excellent Service when you purchase from us. If you get it from others , you may not get our professional service.And If there is anything we can help you in the use, Just contact us ,our team will give you professional support and after-service .