Mitsubishi Electric FX3U-232ADP User Manual page 2

Models : MELSEC FX series manufactured
2N
from July 1st, 1997 FX - ER-ES/UL FX - ET-ESS/UL
2N 2N
Where indicates:32,48
FX -16EX-ES/UL FX -16EYR-ES/UL
2N 2N
FX -16EYT-ESS/UL
2N
from April 1st, 1998 FX -48ER-DS FX -48ET-DSS
2N 2N
from August 1st, 1998 FX -48ER-UA1/UL
2N
from August 1st, 2005 FX -8ER-ES/UL FX -8EX-ES/UL
2N 2N
FX -8EYR-ES/UL FX -8EYT-ESS/UL
2N 2N
For the products above, PLCs manufactured
before March 31st, 2002 are compliant with EN50081-2 (EN61000-
6-4) and EN50082-2
from April 1st, 2002 to April 30th, 2006 are compliant with EN50081-
2 (EN61000-6-4) and EN61131-2:1994+A11:1996+A12:2000
after May 1st, 2006 are compliant with EN61131-2:2003
Standard Remark
EN61000-6-4:2007 Compliance with all relevant aspects
- Generic emission of the standard.
standard • Radiated Emissions
Industrial environment
• Mains Terminal Voltage Emissions
EN50081-2:1993
Electromagnetic
compatibility
EN50082-2:1995 Compliance with all relevant aspects
Electromagnetic of the standard.
• RF immunity
compatibility
• Fast Transients
- Generic immunity
standard • ESD
• Conducted
Industrial environment
• Power magnetic fields
EN61131-2:1994 Compliance with all relevant aspects
/A11:1996 of the standard.
• RF Immunity
/A12:2000
Programmable controllers • Fast Transients
• ESD
- Equipment
• Damped oscillatory wave
requirements and tests
EN61131-2:2003 Compliance with all relevant aspects
Programmable controllers of the standard.
- Equipment EMI
requirements and tests • Radiated Emissions
• Conducted Emissions
EMS
• Radiated electromagnetic field
• Fast transient burst
• Electrostatic discharge
• High-energy surge
• Voltage drops and interruptions
• Conducted RF
• Power frequency magnetic field
Requirement for Compliance with LVD directive
The following products have shown compliance through direct
testing (of the identified standards below) and design analysis
(through the creation of a technical construction file) to the European
Directive for Low Voltage (2006/95/EC) when used as directed by
the appropriate documentation.
Type : Programmable Controller (Open Type Equipment)
Models : MELSEC FX series manufactured
3G
from November 1st, 2008 FX - MT/ES(-A)
3G
Where indicates:14,24,40,60
from December 1st, 2008 FX - MR/ES(-A)
3G
Where indicates:14,24,40,60
from March 1st, 2009 FX - MT/ESS
3G
Where indicates:14,24,40,60
from December 1st, 2009 FX - MR/DS
3G
Where indicates:14,24,40,60
Standard Remark
EN61131-2:2003 The equipment has been assessed
Programmable controllers as a component for fitting in a
- Equipment suitable enclosure which meets the
requirements and tests requirements of EN61131-2:2003
Models :MELSEC FX series manufactured
2N
from July 1st, 1997 FX - ER-ES/UL FX - ET-ESS/UL
2N 2N
Where indicates:32,48
FX -16EYR-ES/UL
2N
from April 1st, 1998 FX 2N -48ER-DS
from August 1st, 1998 FX -48ER-UA1/UL
2N
from August 1st, 2005 FX -8ER-ES/UL FX -8EYR-ES/UL
2N 2N
For the products above, PLCs manufactured
before March 31st, 2002 are compliant with IEC1010-1
from April 1st, 2002 to April 30th, 2006 are compliant with EN61131-
2:1994+A11:1996+A12:2000
after May 1st, 2006 are compliant with EN61131-2:2003
Standard Remark
IEC1010-1:1990 The equipment has been assessed
/A1:1992 as a component for fitting in a
Safety requirements for suitable enclosure which meets the
electrical equipment for requirements of IEC 1010-1:
measurement, control, and 1990+A1:1992
laboratory use
- General requirements
EN61131-2:1994 The equipment has been assessed
/A11:1996 as a component for fitting in a
/A12:2000 suitable enclosure which meets the
Programmable controllers requirements of EN61131-2:
- Equipment 1994+A11:1996+A12:2000
requirements and tests
EN61131-2:2003 The equipment has been assessed
Programmable controllers as a component for fitting in a
- Equipment suitable enclosure which meets the
requirements and tests requirements of EN61131-2:2003
Caution for compliance with EC Directive
Installation in Enclosure
Programmable logic controllers are open-type devices that must be
installed and used within conductive control boxes. Please use the
FX Series programmable logic controllers while installed in
3G
conductive shielded control boxes. Please secure the control box lid
to the control box (for conduction). Installation within a control box
greatly affects the safety of the system and aids in shielding noise
from the programmable logic controller.
Associated manuals
FX Series PLC (main unit) comes with this document (hardware
3G
manual).
For a detailed explanation of the FX Series hardware and
3G
information on instructions for PLC programming and special
extension unit/block, refer to the relevant documents.
Manual name Manual No. Description
FX Series Explains FX Series PLC
3G 3G
JY997D31301
User's Manual specification details for I/O,
MODEL CODE:
- Hardware wiring, installation, and
09R521
Edition maintenance.
FX /FX /
3G 3U
Describes PLC
FX Series
3UC
JY997D16601 programming for basic/
Programming
MODEL CODE: applied instructions STL/
Manual
09R517 SFC programming and
- Basic & Applied
devices.
Instruction Edition
Explains N:N link, parallel
FX Series User's
JY997D16901 link, computer link, no
Manual - Data
MODEL CODE: protocol communication by
Communication
09R715 RS instructions/FX
Edition
232IF.
FX 3G /FX 3U / Describes specifications for
FX Series JY997D16701 analog control and
3UC
User's Manual MODEL CODE: programming methods for
- Analog Control 09R619 FX /FX /FX
3G 3U 3UC
Edition PLC.
FX /FX / Explains the specifications
3G 3U
FX Series JY997D16801 for positioning control of
3UC
User's Manual MODEL CODE: FX 3G /FX 3U /FX 3UC
- Positioning 09R620 and programming
Control Edition procedures
How to obtain manuals
For the necessary product manuals or documents, consult with the
Mitsubishi Electric dealer from where you purchase your product.
Incorporated Items
Check if the following product and items are included in the package:
Included Items
Main units
Product
Dust proof protection sheet
FX -14M ~
3G
FX -60M
3G
Manuals [Japanese version
English version]
Input/output extension units
Product
FX -32E ,
2N
Extension cable
FX -48E
2N
Input/output number label
Input/output extension blocks
Product
FX -8E
2N
FX -16E
2N
Input/output number label
*1 The FX - M /ES-A becomes Chinese version.
3G
1. Outline
For the input/output extension units/blocks, refer to the following
manual.
-
2N
→ Refer to FX
3G Series User's Manual - Hardware Edition.
1.1 Part names
[3] [4]
Series
[2]
[1]
Series
[10]
[11]
No. Name
[1] Peripheral device connecting connector cover
[2] Terminal names
[3] Top cover(S) (40points, 60points type only)
[4] Top cover
[5] Terminal block covers
[6] Input display LEDs (red)
[7] Extension device connecting connector cover
1 unit
1 sheet
*1 1 manual
,
each
1 unit
1 cable
1 sheet
1 unit
1 sheet
[5]
[6]
[7]
[8]
[9]