Advertisement

Hardware Installation Manual
Tofino® Xenon Security Appliance
Tofino Xenon Security Appliance Tofino SA
Technical support
Release 06
09/2018
www.tofinosecurity.com/support

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Tofino Xenon and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Belden Tofino Xenon

  • Page 1 Hardware Installation Manual Tofino® Xenon Security Appliance Tofino Xenon Security Appliance Tofino SA Technical support Release 06 09/2018 www.tofinosecurity.com/support...
  • Page 2 The performance features described here are binding only if they have been expressly agreed when the contract was made. This document was produced by Belden Inc. according to the best of the company's knowledge. Belden Inc. reserves the right to change the contents of this document without prior notice.
  • Page 3: Table Of Contents

    2.3.2 Mounting on a vertical flat surface 2.3.3 Grounding the device Connecting the terminal blocks 2.4.1 Connecting the power supply and the signal contact lines 2.4.2 Wiring the digital input (optional) Operating the device Connecting data cables Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 4 Configuration Making basic settings 3.1.1 USB interface Operating Modes Maintenance and service Disassembly Technical data Further Support Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 5: Safety Instructions

     Operate the product only according to the technical specifications. See “Technical data” on page 41.  Connect to the product only components suitable for the requirements of the specific application case. Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 6 Regarding the properties of this fuse: See “General technical data” on page 41.  The wire diameter of the power supply cable is at least 1 mm² (North America: AWG16) on the supply voltage input. Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 7 The surfaces of the device housing may become hot. Avoid touching the device while it is operating. LED or laser components  LED or LASER components according to IEC 60825-1 (2014): CLASS 1 LASER PRODUCT CLASS 1 LED PRODUCT Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 8 In accordance with the above-named EU directive(s), the EU conformity declaration will be at the disposal of the relevant authorities at the following address: Tofino Security, a division of Belden Inc. Stuttgarter Str. 45-51 72654 Neckartenzlingen Germany The device can be used in the industrial sector.
  • Page 9 à moins que l'emplacement soit connu pour ne contenir aucune concentration de gaz inflammable. Avertissement - Risque d'explosion - La substitution de tout composant peut rendre ce matériel incompatible pour une utilisation en classe I, division 2. Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 10 CONTROL DRAWING to EAGLEONE and TOFINOXE series devices for use in Hazardous Locations Class I Division 2, Groups A, B, C, D Rev. 0 2014-12-01 Document No.: 000174247DNR Page 1/2 Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 11 DOM: ww/yy (Date of manufactur w - week, y - year. Refer to the device label). CONTROL DRAWING to EAGLEONE and TOFINOXE series devices for use in Hazardous Locations Class I Division 2, Groups A, B, C, D Rev. 0 2014-12-01 Document No.: 000174247DNR Page 2/2 Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 12 In Ex Zone 2, only the devices with a corresponding label may be operated. The devices are to be installed and used according to the European Directive 2014/34/EU. Details see the next 2 pages. Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 13 Use of EAGLEONE and TOFINOXE series devices according to the European directive 2014/34/EU Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 14 Control GmbH. DOM: ww/yy (Date of manufactur w - week, y - year. Refer to the device label). Use of EAGLEONE and TOFINOXE series devices according to the European directive 2014/34/EU Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 15 Recycling note  After usage, this device must be disposed of properly as electronic waste, in accordance with the current disposal regulations of your county, state, and country. Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 16: About This Manual

    Hardware Installation Manual  Tofino Configurator User Manual The Tofino Configurator software coordinates configuration, management, and auditing of all Tofino Xenon Security Appliance devices from one workstation. The software provides you with the following capabilities:  Intuitive Windows-based graphical user interface ...
  • Page 17: Description

    This package for helping secure industrial control systems consists of three core components:  Tofino Xenon Security Appliance (Tofino SA) Industrially hardened devices that are installed between control system zones or in front of individual and/or clusters of controllers, computers, and other ICS/SCADA equipment.
  • Page 18: Device Name And Product Code

    10 ... 11 Number: 2 × Fast Ethernet ports Fast Ethernet ports 12 ... 13 Number: 0 × Gigabit Ethernet ports Gigabit Ethernet ports Table 1: Device name and product code Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 19 30 ... 34 Software version 02.0. Software version 02.0 XX.X. Current software version 35 ... 36 Bug fix Bugfix version 01 Current bugfix version Table 1: Device name and product code Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 20 Tofino standard version Software configuration Tofino standard configuration 30 ... 34 Software version Current software version 35 ... 36 Bug fix Current bugfix version Table 2: Sample product code (left column): Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 21 Application case Certificates and Characteristic value declarations Standard applications EN 60950-1 EN 61131-2 UL 508 Oil and gas applications ATEX Zone 2 ISA-12.12.01 – Class I, Div. 2 Substation applications IEC 61850-3 IEEE 1613 Railway applications EN 50121-4 (trackside) Table 3: Assignment: application cases, certificates and declarations, characteristic values...
  • Page 22 Loadable Characteristic value Security Modules (LSMs) 0001 0003 0005 0007 0009 000B 000D 000F 000H 000K 000N 000Q 000S 000V 000X 000Z Firewall (FW) NetConnect (NC) Modbus TCP Enforcer (MB) OPC Classic Enforcer (OPC) EtherNet/IP Enforcer (EIP) Table 4: Combination options of the Tofino SA software modules a.
  • Page 23: Combination Options

    Combination options Item 1 ... 8 9 10 ... 11 12 ... 13 14 ... 15 16 ... 17 19 ... 20 21 ... 22 23 ... 27 ... 28 29 30 ... 34 35 ... Product Device Number: Number: Ethernet Ethernet Tempera...
  • Page 24: Device View

    DSC singlemode socket for 100 Mbit/s F/O connections Grounding screw Hole for mounting using a wall mounting plate Locking gate for removing the device Table 6: Front view (using the example TofinoXe-0200M2T1...) Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 25: Power Supply

    The pin assignment corresponds to MDI-X. Function Receive path RD− Receive path Transmission path TD− Transmission path 4,5,7,8 — Table 7: Pin assignment 10/100 Mbit/s twisted pair port, RJ45 socket, MDI-X mode Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 26: 100 Mbit/S F/O Port

    USB storage device is about to begin. Preparation yellow Lights up (5 s) The load of the configuration files from the Loading process USB storage device is about to begin. Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 27: Controls

    LED will illuminatein green. After a few seconds theMODE, SAVE/ LOAD, and RESET LEDswill flash in green in a left to rightsequence to indicate the USB Saveis in progress. Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 28: Management Interfaces

    Supports the USB master mode  Supports USB 2.0 formatted as FAT or FAT32 (data rate max. 12 MBit/s)  Connectors: type A  Supplies current of max. 500 mA  Voltage not potential-separated Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 29: Input/Output Interfaces

    Further information: “Signal contact (optional)” on page 33 1.10.2 Digital input Further information: “Wiring the digital input (optional)” on page 34 Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 30: Installation

    Installing and grounding the device WARNING FIRE HAZARD Install the device in a fire enclosure according to EN 60950-1. Failure to follow this instruction can result in death, serious injury, or equipment damage. Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 31: Installing The Device Onto The Din Rail

     Obtain mounting hardware which is suitable for your requirements. The wall mounting plate is provided with a Mounting Note that takes you through the mounting procedure.  Follow the Mounting Note provided with the accessory. Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 32: Grounding The Device

    Start connecting the electrical wires only if all the above safety requirements are fulfilled. See “Supply voltage” on page 6. See “Input/output interfaces” on page 7. Failure to follow this instruction can result in death, serious injury, or equipment damage. Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 33: Connecting The Power Supply And The Signal Contact Lines

     Fasten the wires connected by tightening the terminal screws. Signal contact (optional)   Connect the wires according to the pin assignment on the device with the clamps.  Fasten the wires connected by tightening the terminal screws. Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 34: Wiring The Digital Input (Optional)

    The torque for tightening the terminal block on the digital input of the device is 3 lb-in (0.34 Nm).  Mount the terminal block for the supply voltage and the signal contact using screws.  Enable the supply voltage. Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 35: Connecting Data Cables

     Connect the device via the NET 1 port to the external network, such as the Internet. This network is used to set up the connections to the external device or external network. Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 36 NET 2 port and the two devices should be able to ping each other. You will find further information on discovering, configuring, and managing the Tofino Xenon Security Appliance in the Tofino Configurator User Manual. Default settings ...
  • Page 37 The files were possibly support. damaged during the copying operation. Repeat the copying operation. If the condition persists, contact technical support. Table 12: FAULT LED diagnostics for USB Save and Load Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 38 Operational In Operational mode the device is fully MODE Green Solid Mode operational, processes all traffic, and will block any messages not specifically permitted by firewall rules. Table 13: Operating modes Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 39 Tofino Security product pages (www.tofinosecurity.com/support).  Depending on the degree of pollution in the operating environment, check at regular intervals that the ventilation slots in the device are not obstructed. Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 40  Insert a screwdriver horizontally below the housing into the locking gate.  Pull the locking gate down without tilting the screwdriver.  Lift the bottom of the device away from the DIN rail. Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 41 Devices with operating temperature characteristic value E and T (extended): 194 °F (90 °C) Humidity 10%...90% (non-condensing) Air pressure min. 795 hPa (+6562 ft; +2000 m) max. 1060 hPa (−1312 ft; −400 m) Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 42 Type 3 consuming) Connection type 2 pin, screwable terminal block for digital input Tightening torque 3 lb-in (0.34 Nm) Note: For the pin assignment see “Wiring the digital input (optional)” on page Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 43 Dimension drawings  60,6 128,02 2.39 5.04 inch 127,37 5.01 Figure 1: Dimensions Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 44 EMC and immunity  Note: You will find detailed information on the certificates and declarations applying to your device in a separate overview. See table 3 on page 21. Stability Standard Navy applications Railway Substation applications applications applications IEC 60068-2-6, test Fc Vibration 5 Hz ...
  • Page 45 EMC interference Standard Navy applications Railway Substation emission applications applications applications (trackside) EN 61000-6-4 AC and DC supply connections Fulfilled Fulfilled Fulfilled Fulfilled EN 55032 Telecommunication connections Class A Class A Class A Class A EN 61000-6-4 Telecommunication connections Fulfilled Fulfilled Fulfilled Fulfilled...
  • Page 46 EMC interference Standard Navy applications Railway Substation immunity applications applications applications (trackside) Damped oscillation - AC/DC supply connection EN 61000-4-12 line/ground — — — 2.5 kV IEEE C37.90.1 EN 61000-4-12 line/line — — — 1 kV IEEE C37.90.1 Damped oscillation – data line EN 61000-4-12 line/ground —...
  • Page 47 IP20 to a device with IP65, the degree of protection of the overall system is reduced to IP20. Other accessories Order number AutoConfiguration Adapter ACA22-USB (EEC) 942 124-001 6-pin, screwable terminal block (50 pcs.) 943 845-013 Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 48 943 662-121 Tofino Configurator Software 942 016-118 Tofino Modbus TCP Enforcer LSM 942 140-001 Tofino OPC Classic Enforcer LSM 942 140-002 Tofino NetConnect LSM 942 140-004 Tofino EtherNet/IP Enforcer LSM 942 140-003 Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 49 The device generally fulfills the technical standards named in their current versions. The device has an approval based on a specific standard only if the approval indicator appears on the device casing. Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 50 Further Support For technical support, licensing, manuals, and software downloads, please contact the Tofino supplier in your area or use our support portal: www.tofinosecurity.com/support. Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...
  • Page 51 Tofino Xenon Security Appliance Tofino SA Release 06 09/2018...

Table of Contents