Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Lofa Manuals
  4. Controller
  5. MSS-200
  6. Programming manual

Lofa MSS-200 Programming Manual

Hide thumbs Also See for MSS-200:

Advertisement

Quick Links

Download this manual
M S S - 2 0 0
P R O G R A M M I N G M A N U A L

Advertisement

loading

Related Manuals for Lofa MSS-200

Summary of Contents for Lofa MSS-200

  • Page 1 M S S - 2 0 0 P R O G R A M M I N G M A N U A L...

  • Page 2: Page Contents

    Durable IP 63 spray-resistant housing • compressors and pumping systems. • Installs into 2-1/16” Panel Opening The highly flexible MSS-200 is fully Overall length: 3-1/4” • programmable. Its 15 parameters are • Automatic and manual start modes...
  • Page 3 Options The MSS-200 relay interface is an optional add on component for the MSS-200 automatic start stop module. This system was developed to reduce wiring, simplify installation, and add more flexibility to the auto start system. This unique circuit board plugs...
  • Page 4 Alarm Kit (part # 010-1002-00). serious bodily harm. Make sure engine and The Alarm Kit installs to the MSS-200’s equipment have the appropriate protective preheat output and can be programmed to shields and that warning decals are placed sound an alarm prior to engine start.

  • Page 5: Basic Programming Information

    • Number of pole pairs, or if used with Basic Operations a proximity switch, number of pulses The MSS-200 can be controlled directly from the per revolution dial of the MSS-200 by simply pushing either • Belt ratio (pulley diameter. = D1÷ D2) AUTO, MAN and OFF/SET.
  • Page 6 30 sec 6 sec G/S Generator Load Switch Delay #8 The preheat function on the MSS-200 can This parameter is primarily used on generator also be used in combination with a pre-start sets and provides the ability to delay G/S audible alarm.
  • Page 7 This parameter is required only when activate other accessories, i.e., air compressor the MSS-200 is used in solo mode and when relief valve or throttle control. the oil pressure parameter #12 is programmed...
  • Page 8 G/S Frequency-based Load (1) Entering a value greater than zero programs Switch For Generator OR Over-speed Shutdown the MSS-200 controller to a constant speed For Pump #22 (Medium) generator mode. The frequency programmed In step #2 subtract the number entered in parameter 26 then becomes the over-speed in step #1 from the total frequency calculated.
  • Page 9 Over-speed Shutdown Delay Generator Mode OR Engine Warm-up Duration In Pump Mode Pass Code If the MSS-200 is programmed with a pass code This parameter also has two functions: (1) over- or if you are adding a pass code for the first...
  • Page 10 P R O G R A M M I N G T H E M S S - 2 0 0 The MSS-200 is a state-of-the-art electronic automatic engine start-stop controller that can be programmed to each customer’s unique requirements. The system programs from the outside of the compact cylindrical design using a simple binary code sequence.
  • Page 11 P R O G R A M M I N G G U I D E Number Of Button to Parameter Multiplier Factory Range Indicator Pushes Of Push Setting Decrease Increase OFF/SET Value (-) Value (+) OFF/SET+ Turn On Turn key System OFF/SET Preheat...
  • Page 12 P R O G R A M M I N G G U I D E Factory Number Of Button to Multiplier Range Parameter Setting Pushes Of Push Indicator Decrease Increase OFF/SET Value (-) Value (+) OFF/SET Oil Pressure Delay 8 sec OFF/SET (-) MAN...
  • Page 13 (+) AUTO electricity] automatic start when system is grounded Note: When the MSS-200 is programmed in the standby mode which does not consume electricity, the AUTO input terminal on the MSS-200 must be connected to a ground at all time.

  • Page 14: Manual Auto

    E N T E R I N G A PA S S C O D E The MSS-200 allows the user to input a system. One LED will blink indicating the 3-digit pass code to prevent first pass code. Press the OFF/SET button...
  • Page 15 LED Explanation While MSS-200 Is In AUTO Mode Automatic self-test. The MSS-200 is turned on (System Energized). MSS-200 is awaiting start signal via ground (Switch contact is open). Changing to manual start mode is possible by pressing the OFF/SET and then the HAND button.
  • Page 16 LED Explanation While MSS-200 Is In Manual Mode Automatic self-test. The MSS-200 is turned on (System Energized). The MSS-200 is in off position and is awaiting a manual start signal (Pushing HAND button will start engine). Changing to AUTO mode is possible by pressing the AUTO button.
  • Page 17 N O T E S...
  • Page 18 N O T E S...
  • Page 19 N O T E S...
  • Page 20 463-3000-00 - Initial Release 770.569.9828 770.569.9829 www.LOFA.net PHONE ©2002 LOFA Industries, Inc. LOFA Industries, Inc. is constantly striving to improve its products and must, therefore, reserve the right to change designs, materials, specifications and prices without notice. Printed in the USA. 03/02...