Advertisement
@
TwSTALLATION
AND
CONNECTIONS
m
=l (ol
-1
o1
,l
)
Rear panel:
1
MAINS
2
VOLTAGE
SELECTOR
3
ANALOG
REC
ANALOG
PLAY
4
DIGITAL
IN
DIG
AL
OUT
5
EASYLINK
BUS
Be sure
to connect the
unit
to the
correct
mains voltage
via
the
supplied mains
cable.
Select
the
mains voltage
corresponding
to the
local mains
voltage
(220-240
V,
110-120
V).
lnput sockets
(lefVright)
for
an
analog audio signal
.
Output sockets
(lefVright)
of
an
analog audio
signal.
lnput socket for
a
digital audio
signal.
Output socket of
a
digital
audio
'
signal.
For
connecting the
'DCC
380' to
the
PHILIPS HiFi
MidiSystem
'FS
380'. 'CD DUBBING'is
only
possible
with this
BUS
connection.
ANALOG
REC -
lnsert
the
red plug
to
the
R
socket
and
the
other
plug to
the
L
socket
of
your
'DCC
380'. lnsert
the
two
other plugs to the
DCC
REC
sockets
of
your amplifier.
You
can also use
the
TAPE
or
AUX
outputs of
your amplifier.
ANALOG PLAY-
lnsertthe
red plug
tothe
R
socketand
the
other
plug to
the
L
socket
of
your
'DCC
380'. lnsert
the
two
other plugs
to the
corresponding
DCC PLAY
sockets of
your amplifier.
DIGITAL
lN
- lnsert one plug of
the
cinch
lead
to the
input
socket
of
your 'DCC 380' and
the other
plug
to
the
corresponding digital
output socket of
a
CD
player.
DIGITAL
OUT
-
This
output
supplies
a
digital signal
via
an
electrical path; for
this
reason it can only be connected
to
a
product
with
a
digital
input e.g.
amplifier,
DCC
or
DAT.
Use
a
cinch
lead (not supplied)
with
one
cinch
plug
on
either
end.
EASYLINK
BUS
- lnsert one
plug
of the cinch
lead
to
one
socket
of
your 'DCC 380' and
the other
plug
to
the
EASYLINK
BUS
socket
of
the
CD
player,
which
has
to
be
connected to
the
EASYLINK BUS
socket of the
receiver.
With the other socket you
have
the
possibility
to
make
a
connection to
the
EASYLINK
socket of
e.g.
a
CD
or
DCC
player.
o
Select
the
local
mains voltage
at
the
rear of
the
'DCC
380'.
o
Connect the smaller
plug of
the supplied
mains cable to
the
MAINS socket of
the
'DCC
380'and the
mains plug to the
wall
outlet.
.
You can
now start the operation.
En.loy
yourself
!
A
few recommendations:
o
lf
the unit
is
not used
for some
time,
switch the unit off
and
pull
the
mains
plug
out.
By doing
this, you
will
protect
it
from
lightning damage.
o
When you pull
the
mains
plug
out, do not take
it
by the
cable,
but
by
the connector
shell.
r
When you
have pulled
the mains
plug
out,
do not
touch the
two
contact
pins,
as
the'DCC
380'
needs
a
few
seconds
to
discharge.
lnstallation:
WARN!NG
Do
not connect the
set
to
the mains until all other
conneetions
have been made and
the
mains
voltage
has been checked.
The
type
plate is located on
the
rear
of the
unit.
.
Do not place
the
'DCC
380'
in
humid,
too
warm
or hot areas
(e.9. on
top of the amplifier),
near
magnetic
fields
(e.g.
TV)
or
in
dusty
rooms,
as
this
will
reduce
the
life
of the
unit.
.
When
positioning
the unit, put the
'DCC
380' on
the
bottom of the
stack.
.
Keep
a
f
ree space of
a
few centimeters
around
the
unit and
do
not
cover any vents.
o
After you
have
positioned
the
unit correctly,
it
has
to adapt
to
the
new ambient
temperature.
Leave
the
'DCC
380'for
about
30
minutes, to allow possible condensation water
to
evaporate.
Failure
to
follow
these
instructions
may cause
damage
to the electronics!
o
Connect
the units
using
the
supplied cables
as
follows:
4
2
5
4
Advertisement
