Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Bazooka RS10A-hp
Summary of Contents for Bazooka RS10A-hp
- Page 2 Today we market our patented speaker systems worldwide and the high quality of the Bazooka brand is well respected by consumers and dealers of all nationalities. When properly installed, Bazooka subwoofer speaker systems will give you years of clean uninterrupted sound reproduction.
-
Page 3: Table Of Contents
If you have any questions contact the SAS Technical Support Department at: Phone - (225) 272 7135 • Fax - (225) 272-9844 In Canada: • (604) 988 2966 Email - tech@bazooka.com • Website - www.bazooka.com CONTENTS ...... -
Page 4: System Features
Weight 15 lbs. Powe 150 RMS BASS TUBES ® * The efficiency levels of all Bazooka subwoofer speaker systems are measured in the typical environment: In the low bass region with one watt of power. SYSTEM FEATURES SPECIFICATIONS RS6A-HP RS8A-HP 6.5 "... -
Page 5: Installation
INSTALLATION T R U C K I N S T A L L A T I O N Figure 1 tube size is exagerated for emphasis S E D A N I N S T A L L A T I O N Figure 2 tube size is exagerated for emphasis H A T C H B A C K I N S T A L L A T I O N... -
Page 6: Installation
Please take time to read through this manual and plan out your installation before you begin! Locate an area in the rear of the vehicle where you would like to place the Bazooka speaker systems. The location you have selected must meet the following requirements in... -
Page 7: Mounting The Bazooka
Figure 4 MOUNTING THE BAZOOKA Bottom Figure 5 Figure 6 With the top side of the buckle facing up (see figure 4), lace the strap through the mounting base illustrated in figure 5. After the strap is com- pletely laced through... - Page 8 MOUNTING THE BAZOOKA Figure 7 Figure 8 Place each mount- ing base under the Bazooka so that the apex at the bottom of the tube sits inside the mounting base as in figure 7. Move the bases so that they are spaced approximately 3”...
-
Page 9: Mounting The Bazooka 6
Due to the jarring and shifting that can occur in a vehicle, the mounting straps may stretch or loosen. We recommend that you check the straps regularly to assure that your Bazooka is mounted securely in place. MOUNTING THE BAZOOKA... -
Page 10: Wiring Diagram
WIRING DIAGRAM When using high level inputs, take the time after you make all wiring connections to run through the AM I IN PHASE? procedure of this manual to confirm that your inputs are in correct electrical phase and the proper bass response is being produced. -
Page 11: Power Wire
The power wire carries substantial currents and could induce noise. DO NOT substitute the 15 amp fuse included with the Amplified Bazooka with anything other than the same fast blow current rated fuse. Substitution or deletion will void the product's warranty and may cause damage to your car or the amplifier. -
Page 12: Remote Turn On Options
(high level or low level input). Locate the Auto/Off Jumper Clip located on the back of the unit, SAS ships the Amplified Bazooka with this Jumper in the Off Position. To use the Auto Turn-On Option the Jumper must be placed in the Auto Position. The Jumper Clip must be lifted off of the middle and right hand pins and reinserted across the left hand GROUND WIRE CONT. -
Page 13: Amplifier Status Led
The white color LED on the Amplified Bazooka will light up GREEN when power, ground and remote are all connected properly. If it lights up RED, the Amplified Bazooka is in pro- tection mode which can indicate a short in the wiring or a problem with the amplifier. - Page 14 When one of the Amplified Bazooka's High-level Input channels is out of phase elec- trically with the other High-level Input channel your Bazooka will sound as if it has lit- tle or no output, and any output that is produced may sound distorted. If you suspect that your Bazooka is out of phase, use the AM I IN PHASE procedure to diagnose and correct the Bazookas' output, and proper bass response will be produced.
-
Page 15: Adjusting The Crossover
The built-in crossover on the Amplified Bazooka is a 18 dB per octave electronic low pass filter, it has a 60 Hz to 250 Hz variable crossover point. Select the crossover point that you feel best fits your system design. Set the potentiometer labeled XOVER to the point you selected, 60 Hz being all the way to the left (coun- terclockwise) and 250 Hz being all the way to the right (clockwise). -
Page 16: Email - Tech@Bazooka.com • Website - Www.bazooka.com
Email - tech@bazooka.com • Website - www.bazooka.com In Canada: (604) 988 2966 15049 Florida Blvd., Baton Rouge, LA. 70819 , SAS, BAZOOKA, BASS TUBES, and LISTEN TO YOUR EARS are registered trademarks of Southern Audio Services, Inc. PAT. NO. 4,567,959 • PAT NO. 5,097,513 1003129704A...
Need help?
Do you have a question about the RS10A-hp and is the answer not in the manual?
Questions and answers