JT Revolution Owner's Manual

RuLES OF SAFE pAINTbALL
MARkER HANDLINg
1. Treat every paintball marker as if it were loaded.
2. Never point the paintball marker at anything you don't wish
to shoot.
3. Keep the paintball marker on safe until ready to shoot.
4. Keep the barrel plug in the paintball marker's muzzle when
not shooting.
5. Always remove gas source before disassembly.
6. Store the paintball marker unloaded and degassed in a
locked place.
7. Follow warnings listed on gas source for handling and

storage.

8. Never use anything other than .68 caliber paintballs.
9. Always wear proper eye protection designed specifically to
stop paintballs.
10. Never shoot a person who is not wearing proper protection.
11. Always measure velocity before playing paintball.
12. Never shoot at velocities in excess of 300 feet per second.
OWNER'S MANuAL
OWNER'S MANuAL

OpERATINg INSTRucTIONS:

18 vOlT AGITATOR lOADeR
18 vOlT AGITATOR lOADeR
CAUTION: Installing batteries incorrectly can cause damage to
the circuit board!
Step 1. Insert Batteries. Slide the battery door off to insert
two 9 volt batteries in through the bottom of the loader. Make
sure the battery terminals are correctly oriented by noting the
This Manual Contains:
polarity markings that are located on the outside of the loader
• Warranty Information • Operating Instructions
body and the battery door. Push on the batteries to compress
• Maintenance Instructions • Annotated Diagram
the contact springs and slide the door back in place.

SpEcIFIcATIONS:

Step 2. Install loader on paintball marker and open spring
loaded flip lid and fill through the lid opening. Leave some
Power 18 Volt
(requires two 9 volt batteries not included)
room for ball movement.
Capacity Approx. 180 Paintballs
(.68 cal)
WARNING: Do not overfill the loader. This will cause prop jams
Switching Infrared Sensor
or performance loss and could cause damage to the loader as well.
Servo Ratio 172:1
3. Switch on the power. The power switch and low-voltage
Action Agitated gravity feed
indicator are located on the left side of the loader. The
agitator activates when the infrared (IR) sensor does not
The JT Revolution hoppers are electronically agitated paintball
detect a paintball in the neck of the feed tube. Once
loaders designed for high performance and reliability. The
activated the prop will begin to spin until the feed tube
patented design allows for the high rates of fire encountered
becomes full. The IR sensor will then automatically shut
with the modern paintball marker.
the servo off.
WARNING:
Eye protection designed specifically for
paintball must be worn by the user and persons within range.

Battery Indicator

Safety is no accident.
The JT Revolution's voltage sensor circuitry will cause
the LED indicator to blink and eventually glow steady as
WARNING!
your batteries become discharged. You should replace the
batteries when the LED glows steadily with the switch on
and servo motor not running. You will begin losing maximum
GUNS AND PAINTBALL
performance as your batteries deplete from this point.
GUN ACCESSORIES ARE NOT TOYS!
STORAgE
- Careless use or misuse may result in serious bodily injury or death!
- Eye protection designed for paintball must be worn by the user and To extend the product and battery life, always turn the power
all persons within range. switch to off and remove the batteries during storage.
- Must be 18 years of age or older to operate or handle any paintball gun

MAINTENANcE guIDE

and paintball gun accessories without adult or parental supervision.
- Read and understand all cautions, warnings, and operating manuals

DISASSeMBly

before using any paintball gun or paintball gun accessory.
- Do not aim paintball gun at eyes or head of people or at animals. Step 1. Empty out any unused paintballs and remove loader
- Paintball guns are to be used with Paintballs only. from the paintball marker.
- To prevent fire or shock hazard, do not expose unit to rain or moisture.
Step 2. Remove the feed adapter (if used), the battery door
- To prevent fire or shock hazard, do not immerse unit in liquids.
and the batteries.
- To prevent fire or shock hazard, do not disassemble any electronic
paintball device.
Step 3. Remove the eight body screws from the side of the
- The disposal of the battery used to power this product may be
loader.
regulated in your area.
Step 4. Separate the two body halves of the loader and
- Please conform to all local or state regulations with regard to battery
remove the flip lid and flip lid spring.
disposal.
- Use common sense and have fun.
Step 5. Remove the main circuit board assembly, infrared
Any tampering with the unit voids your warranty. There are circuit board, servo motor and wiring harness from
no consumer serviceable parts inside the unit. The use of non the left body half.
factory authorized components within this product may cause a
critical failure, fire or shock hazard.

CLEANING

IN NO EVENT SHALL SELLER BE LIABLE FOR ANY DIRECT,
Step 1. The body and flip lid may be cleaned with soap and
INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY
water once they are separated from the Circuit
NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY
Boards and motor. Keep moisture away from all
DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
electronic components of the JT Revolution.
WARNING:
This product contains one or more chemicals that
Step 2. If the Circuit Boards or motor are contaminated with
are known to the State of California to cause cancer and birth
paint, wipe them off with a clean, dry cloth. The
defects or other reproductive harm. Wash hands after handling.
components can be separated if necessary by
unplugging wiring harness.
Made in China.

ReASSeMBly

Step 1. Plug the Circuit Board back into the servo unit.
NOTe: The plugs are connected properly when the white wires
face the left half of the loader.
Warning: Improper assembly will damage electronics.
See diagram below.
Step 2. Reinstall the servo unit back into left half of the
loader. Make sure the switch aligns properly in body.
Ensure wires from the harness are pressed back into
this half of the loader when you have completed this
step. This is to prevent pinching the wires during
assembly of the two body halves.
Step 3. Install flip lid spring and flip lid into the right half of
the loader Couvercie à abattant
Step 4. Carefully align the body halves together using the
flip lid pin as a guide. Once the body halves are
together and free of binding, snap the flip lid down
in place.
Step 5. Install the eight body screws. Avoid over tightening
the screws to ensure you do not strip the plastic
body.
Step 6. Install the batteries and battery door. Now your JT
Revolution is ready for action.
WARNING: Replace harness connectors back in location as Conjunto de laca de circuito principal
shown. Assembling harness incorrectly will damage electronics.
Tabs Up
3 Pins
Porte du compartment a piles
Tabs Up
Circuit
Board IR Circuit
Board
Servo Motor
4 Pins
LIMITED LIFETIME
WARRANTY
INFORMATION

TROubLESHOOTINg cHART

(ORIGINAL PURCHASE
For further assistance in troubleshooting your loader contact us at:
RECEIPT REQUIRED)
JT Paintball warrants that this
JT Paintball United States JT Paintball Canada
product is free from defects in
11723 Lime Kiln Rd. 98 Bessemer Ct Unit 4
materials and workmanship for as
Neosho, MO 64850 London ON N6E 1K7
long as it is owned by the original purchaser, subject to the
(800)-220-3222 (866)-685-0030
terms and conditions set forth below. JT Paintball will repair
www.paintballsolutions.com www.jtpaintball.com
tech@paintballsolutions.com or replace with the same or equivalent model, without charge,
any of its products that have failed in normal use because of
a defect in material or workmanship.
Symptom Cause Solution
JT Paintball is dedicated to providing you with products of
the highest quality and the industry's best product support
Loader is Not Functioning Depleted or Replace Batteries
available for satisfactory play.
or is Losing Maximum Low Batteries
Performance
Purchaser should register product to activate warranty.
Register your product by:
1. Online at www.paintballsolutions.com
Loader Is Not Operating Broke Paint in Clean the Loader
2. Complete the product registration card (if applicable) and
Properly the Loader
mail along with a copy of your receipt to Paintball Solutions,
11723 Lime Kiln Rd., Neosho, MO 64850.

WHAT THIS WARRANTY DOES NOT COVER

I Have Replaced Batteries Damaged Visit a Local Service
This warranty does not cover problems resulting from abuse,
and Cleaned My Loader Electronics Center, or Contact
the unauthorized modification or alteration of our product,
and it Still Will Not Operate Paintball Solutions at
800-220-3222 problems resulting from the addition of aftermarket products
(U.S.)
and scratches or minor superficial imperfections. Due to the
The Loader Jams Too Many Paintballs Leave Some Room for nature of paintball products it is important that the product be
in the Loader, or Ball Movement When
maintained by the user as indicated in the product manual
Low Quality out of Filling the Loader
to remain in good operating condition. Your Limited Lifetime
Round Paintballs
Warranty will be void if you fail to maintain the product as
recommended in the product instruction manual. In addition,
certain parts of a product may be subject to wear through
regular usage. Replacement and repair of such parts is the
PATENT(S): See www.paintballsolutions.com/patents © 2011-2012 KEE
responsibility of the user throughout the life of the product.
Action Sports. All rights reserved. This KEE Action Sports product is
These parts are not covered under the Limited Warranty.
protected by one or more United States and International patents. KEE
Examples of this type of part include (but are not limited to)
Action Sports Trademarks, Designs and Copyrights are protected by
goggle lens, straps, O-ring seals, cup seals, springs, ball
one or more United States patents and International Law. For more
information contact KEE Action Sports at info@keeactionsports.com detents, batteries, hoses, drive belts, gears and any part
Flip Lid
Tapa valvén
Main Circuit Board Assembly
Plaquette de circuits principale
Battery door
Puerta de bateria
Servo Motor & Wiring Harness
Servomotor y caja de cableado
Servomoteur et faisceau de câblage
of a product subject to continuous impact from paintballs.
Hydrotesting of air cylinders is not covered under this
warranty.
The Limited Lifetime Warranty also does not cover incidental
or consequential damages. This warranty is the sole written
warranty on Empire's product and limits any implied warranty
to the period that the product is owned by the original
purchaser. Some states, provinces and nations do not
allow the limitation of implied warranties or of incidental
or consequential damages, so the above limitations or
exclusions may not apply to you. This warranty gives you
specific legal rights and you may also have other rights which
vary from state to state, province to province, nation to nation.
If you should encounter any problems with your product and
you have added aftermarket parts on your product, please
test it with the original stock parts before sending it in. Always
unload and remove air supply before shipping markers. Do
not ship your air supply tank if it is not completely empty.
Shipping a pressurized air supply tank is unsafe and unlawful.
Remove all batteries from products prior to shipping.
This Limited Warranty gives you specific legal rights, and
you may also have other rights which vary from state to
state. Some states do not allow the exclusion of incidental or
consequential damages.
For warranty parts, service or information in the U.S.
JT Paintball United States
11723 Lime Kiln Rd.
Neosho, MO 64850
(800)-220-3222
www.paintballsolutions.com
tech@paintballsolutions.com
Body Shell (left)
Cobertura (izquierda) del cuero
Côté gauche du boitier
Body Shell (right)
Cobertura (derecha) del cuerpo
Côté droit du boîtier
Prop
Propulsor
Hélice
infrared Circuit Board
Place de ciruito infrarrojo
Plaquette de circuits à infrarouge
JT Paintball Canada
98 Bessemer Ct Unit 4
London ON N6E 1K7
(866)-685-0030
www.jtpaintball.com
Body Screws (8)
Tornillos del cuero (8)
Vis d'assemblage (8)