Advertisement
Quick Links
WHAT'S IN THE BOX
• LED FIXTURE
• MOUNTING HARDWARE
WHAT YOU'LL NEED
• SCREWDRIVER
• WIRE CUTTERS
• WIRING SUPPLIES AS SPECIFIC BY
ELECTRICAL CODE
FL2 3K SERIES
FLOOD LIGHTS
INSTALLATION INSTRUCTIONS
For use with:
FL2-15YK | FL2-30YK | FL2-50YK
FL2-100YK | FL2-150SF | FL2-220SF
FL2-300SF | FL2-300MA | FL2-150SF-347
FL2-220SF-347 | FL2-300SF-347
FL2-300MA-347
IMPORTANT
Before assembling your CORE
PRODUCTS CANADA fixture, please
make sure that you carefully read
through this instrucEon sheet.
Consider having your fixture installed
by a qualified licensed electrician.
Note: The important safeguards and
instrucEons that appear in this sheet
are not meant to cover all possible
condiEons and situaEons that may
occur. It must be understood that
common sense, cauEon, and care are
factors that cannot be built into any
product. These factors must be
supplied by the person(s) caring for
and operaEng the fixture.
CORE Products Canada Ltd.
82-86 Carrier Drive
Toronto, ON Canada
M9W 5R1
CORE-PRODUCTS.CA
1
Advertisement
Summary of Contents for Core FL2-15YK
- Page 1 WHAT’S IN THE BOX occur. It must be understood that common sense, cauEon, and care are factors that cannot be built into any • LED FIXTURE product. These factors must be • MOUNTING HARDWARE supplied by the person(s) caring for and operaEng the fixture. WHAT YOU’LL NEED • SCREWDRIVER • WIRE CUTTERS • WIRING SUPPLIES AS SPECIFIC BY CORE Products Canada Ltd. ELECTRICAL CODE 82-86 Carrier Drive Toronto, ON Canada M9W 5R1 CORE-PRODUCTS.CA...
- Page 2 STEP-BY-STEP INSTRUCTIONS This LED Flood light uses the latest in solid state lighEng technology for long life, low maintenance, and high efficiency. The same as tradiEonal HID lighEng. An internal power- factor-corrected switch-mode supply allows it to be used from any nominal 100-277V, 60Hz AC supply without any variaEon in light output. Suitable for use in the following locaEons: ambient temperature of -20~+40°C and wet locaEons. The fixtures can be installed using three installaEon methods, dependent on the model you purchased: Direct mount to surface, mounEng with a slipfiger, and mounEng with mounEng arm. WARNING To avoid the risk of fire, explosion, or electric shock, this product should be installed, inspected, and maintained by a qualified electrician only, in accordance with all applicable electrical codes. To avoid electric shock: • Be certain electrical power is OFF before and during installaEon and maintenance. • Luminaire must be connected to a wiring system with an equipment-grounding conductor. To avoid explosion: • Make sure the supply voltage is the same as the rated luminaire voltage. • Do not install where the marked operaEng temperatures exceed the igniEon temperature of the hazardous atmosphere. • Do not operate in ambient temperatures above those indicated on the luminaire nameplate. • Keep lens Eghtly closed when in operaEon. HOW TO DIRECT MOUNT TO SURFACE 1. Use expansion bolts to secure the fixture on mounEng surface. 2. Keep enough length wires to ensure adjusEng angle unhindered. 3. ...
- Page 3 HOW TO MOUNT WITH SLIPFITTER 1. Adjust the fixture orientaEon by turning the bolt. 2. Use a post of diameter 2.36” for mounEng, and Eghten with screws. You can open the side cover from the side to perform the connecEon. 3. Connect wires into wiring terminal; white wire to “Neutral” terminal, black wire to “Live” terminal, green wire to “Ground” terminal; and fix them by screws. 4. Restore the electricity and check the operaEon of your new lighEng fixture. HOW TO MOUNT WITH ARM 1. Directly screw the lamp onto the lamp post. 2. You can open the side cover from the side to perform the connecEon. 3. Connect wires into wiring terminal; white wire to “Neutral” terminal, black wire to “Live” terminal, green wire to “Ground” terminal; and fix them by screws. 4. Restore the electricity and check the operaEon of your new lighEng fixture.
Need help?
Do you have a question about the FL2-15YK and is the answer not in the manual?
Questions and answers