Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for DEMAG DRC-DR D2
- Page 1 Operating instructions DRC-DR D2 radio receiver...
-
Page 2: Table Of Contents
Manufacturer Demag Cranes & Components GmbH P.O. Box 67, D-58286 Wetter Telephone (+2335) 92-0 · Telefax (+2335) 927676 www.demagcranes.com Contents Foreword Copyright Customer service Liability for Defects Limitations of liability Definitions Safety instructions Symbols Appropriate use Inappropriate use Basic information on safety... -
Page 3: Foreword
Infringements are an offence resulting in obligatory compen- satory damages. All industrial rights reserved. Our after-sales service will provide you with all technical information on Demag 1.2 Customer service products and their systematic application. Should you have any questions regarding our products, please refer to one of our after-sales service stations, the relevant representative or the manufacturer. -
Page 4: Liability For Defects
We expressly point out that only genuine Demag spare parts and accessories ap- proved by us may be used. Accordingly, this also applies to other manufacturers‘ parts supplied by us. -
Page 5: Definitions
1.5 Definitions Owner Owners (employer, company) are defined as a person who owns such a system and who uses it appropriately or allows it to be operated by suitable and instructed persons. Operating personnel/operator Operating personnel or operators are defined as persons entrusted by the owner of the system with the operation of the system. -
Page 6: Safety Instructions
Despite all of the technical precautions taken by Demag, it cannot be entirely ex- cluded that the transmission characteristics of other radio systems are impaired,... - Page 7 Whether and to which extent such measures are required can only be determined by means of suitable measurements on site or when the system is put into operation. Demag is not responsible for such addi- tional technical measures.
-
Page 8: Inappropriate Use
2.3 Inappropriate use Certain work and practices are prohibited when using the product as they may involve danger to life and limb and result in lasting damage to the product, e.g.: • Manipulating electrical equipment • Connecting the unit to power supply with voltage or frequency other than those specified on the type plate •... -
Page 9: Safety Instructions For Installation And Disassembly
Modifications, additions to and conversions of the product which might impair safety in any way must not be carried out without the approval of Demag. Safety devices must not be rendered inoperative. -
Page 10: General Description
DR rope hoist. The radio receiver communicates with the electrical equipment of the rope hoist via a CAN interface. For use of the DRC-DR radio receiver, the DR rope hoist must be provided with a Demag rope hoist control system. - Page 11 3.2.1 Downwards compatibility of For combining DRC-10 D2 transmitters with D1 type receivers DRC-10 D2 transmitters DRC-DR, part no. 719,441 45 DRC-MP, part no. 773 432 44 these transmitters must be programmed for operation at a fixed frequency (chapter „Programming parameters of the DRC-10 handheld transmitter“, section 1.6). The table below shows an overview of the possible combinations 3.2.2 Compatibility Receiver...
-
Page 12: Technical Data
Technical data DRC-DR radio receiver/PCB Output CAN bus LED indicators for Power on Radio transmitter/receiverl (HF) available Data telegrams decoded without error Type of enclosure IP 55 integrated in rope hoist controls Ambient temperature – 20° to + 70° C. Weight of radio receiver 60 g Supply voltage... -
Page 13: Fitting The Radio Receiver Card
Fitting the radio receiver card To install the radio receiver card, proceed as follows: • Before starting any installation work, disconnect system from the power supply. • Install the radio receiver card in the appropriate slot Slide the radio receiver card into the appropriate slot 42354344.eps •... - Page 14 • Connecting the flat cable from the radio receiver to the controller card of the rope hoist control system 42354644.eps 42354844.eps 42354744.eps • With the above steps, installation of the radio receiver card has been complet- ed. Before the system is put into operation again, make sure that other control components such as, for example, the DSE-8R or DSE-10R control pendant with cable, have been disconnected from the system.
-
Page 15: Function Check After Installation
Function check after installation A general function check of the radio receiver is possible by means of the light diodes on the radio receiver card. • The yellow LED flashes, when the receiver is supplied with current and no DRC-10 hand-held transmitter or DRC-J joystick control system has been assigned yet. -
Page 16: International Postal Registration
International postal registration In the following countries, transmitters and radio receivers of the DRC-10 D2 range in the standard delivery form (part no.: 773 591 44) can be operated without any registration or operating fee: Countries Frequency range Australia 433-MHz ISM band Belgium 433-MHz ISM band Denmark... -
Page 17: Ec Conformity Declaration
# = Modifi cations compared Class. no. Normung DCC 715 IS 975 to previous issue Reproduction in whole or in part only with prior consent of Demag Cranes & Components GmbH, D-58286 Wetter Subject to change. Not liable for errors or omissions. -
Page 19: (For Authorized Personnel Only)
(For authorized personnel only) Operating instructions Programming parameters of DRC-DR radio receiver... -
Page 20: Menu For Programming Parameters Of The Radio Receiver
Menu for programming parameters of the radio receiver The radio receiver parameter programming menu is used by specially trained personnel for programming parameters of the radio control system. The following information of the radio control system can be displayed and four of the settings can be changed using this menu: Code Information... -
Page 21: Displaying The Current Parameters
1.2 Displaying the current Only parameters are first displayed after activation of the menu. The display starts with parameter 001, i.e. the Baud rate used by the radio receiver on the CAN bus. parameters The colon following the parameter code 001 indicates the display mode: K564 001: 125kBIT... -
Page 22: Can Baud Rate
1.5 CAN Baud rate 1.5.1 Default setting Precondition: Parameter code 001 activated The default setting set in the factory is a transmission speed of 125 kbit. The current Baud rate is shown in the display. To navigate, use the following keys: 1.5.2 Display mode DRC-10 DRC J... -
Page 23: Switching On And Off The Can Heartbeat Function
1.7 Switching on and off the CAN heartbeat function 1.7.1 Default setting Precondition: Parameter code 003 activated The default setting set in the factory is ”Hearbeat off”. 1.7.2 Display mode The current setting for the CAN function heartbeat is shown in the display. To navigate, use the following keys: DRC-10 DRC J... - Page 24 Press the F1 key to accept the selected character and to change to the next posi- 1.8.4 Changing to the next position tion of the crane identification. 1.8.5 Confirming the new crane Actuate the F2 key when the crane identification has been entered completely to identification transmit the new crane identification to the assigned radio receiver.
-
Page 25: Displaying The Serial Number Of The Radio Receiver, Parameter Code 005
Displaying the serial The serial number of the radio receiver is shown in the display. This display is only provided for information and the displayed value cannot be changed. To navigate, number of the radio use the following keys: receiver, DRC-10 DRC J Function... - Page 26 Notes...
- Page 27 Notes...
- Page 28 Reproduction in whole or in part only with prior consent of Demag Cranes & Components GmbH, D-58286 Wetter Subject to change. Not liable for errors or omissions.
Need help?
Do you have a question about the DRC-DR D2 and is the answer not in the manual?
Questions and answers