Related Manuals for Galaxy 3000M
Summary of Contents for Galaxy 3000M
- Page 1 3000M - 3500M - 3500Msi (White and Chrome Models) SMART ELECTRIC SHOWERS Installation and User Guide IMPORTANT: This booklet should be left with the user after installation and demonstration.
- Page 2 THIS APPLIANCE CAN BE USED BY CHILDREN AGED FROM 8 YEARS AND ABOVE AND PERSONS WITH REDUCED PHYSICAL, SENSORY OR MENTAL CAPABILITIES, OR LACK OF EXPERIENCE AND KNOWLEDGE IF THEY HAVE BEEN GIVEN SUPERVISION OR INSTRUCTION CONCERNING USE OF THE APPLIANCE IN A SAFE WAY AND UNDERSTAND THE HAZARDS INVOLVED.
- Page 3 pressure fluctuations. These can result from toilets being flushed or We recommend that the installation is done in taps being turned on and off. the following sequence. When this happens your showering a. Fixing the shower to the wall temperature will be held within a controlled b.
- Page 4 to have the connections on the right side or This allows for correct and accurate the left. (see fig.3). alignment of your shower before marking and fixing the bottom position. You may wish to leave both screws at this stage loose as the holes are elongated to allow for adjustment after other connections have taken place.
- Page 5 Note: You may be charged for a service call sealant sparingly, avoiding excess finding its if it is due to incorrect installation way into the shower operating parts. 4. With the isolating valve connected, flush the pipe work through to remove 5.
- Page 6 WARNING: WARNING: DO NOT FIT A TAP ON THE FAILURE TO COMPLY WITH THESE SHOWER OUTLET. INSTRUCTIONS COULD RESULT IN WARNING: FAILURE OF THE TERMINAL BLOCK TAKE CARE TO AVOID WARNING: RESTRICTING THE OUTLET OF THE THE UNUSED SUPPLY TERMINAL PRESSURE RELIEF DEVICE.
- Page 7 White Models See sheet provided for Chrome Models...
- Page 8 TO START THE SHOWER 7. Set the power select knob to ‘Cold’ (9 o’clock position) and turn temperature Press Button ‘C’ - Water will start to flow. knob fully anti-clockwise to allow the unit to fill with water prior to any heat settings Set your desired power setting - normally ‘High’...
- Page 9 TO STOP THE SHOWER WARNING: Press Button ‘C’ to Stop the shower (fig.13). DO NOT OPERATE THE SHOWER IF Water will cease to flow. WATER IS DISCHARGED FROM THE Switch off the electricity PRESSURE RELIEF VALVE. Turn off electricity at the ceiling switch or supply to shower at MAINTENANCE IS REQUIRED local isolator.
- Page 10 CLEANING THE FILTER The filter can be cleaned in order to maintain the performance of the shower if required. It is essential that this operation is carried out by a competent person. WARNING! It is recommended that the shower unit and SWITCH OFF THE ELECTRICITY AT accessories be cleaned using a soft cloth and that the use of abrasive or solvent based...
- Page 11 3500M Model. Water This is normal on the continues The shower includes a shutdown to flow feature that means water will when continue to flow for around 6 button ‘C’ seconds after Button ‘C’ is pressed. pressed Broken Please contact our after sales parts service department (See Section 5).
- Page 12 Effect of Seasonal Incoming Water Temperature Changes The required water temperature is achieved by adjusting the rate of water flow. The diagram shows the principle involved in relating temperature rise to flow rate. The higher the water rate the lower the 1.
- Page 13 k) Wall Fixing Key-Hole Slot a) Thermal Cut-Out l) Alternative key-Hole slot b) Heat Exchanger m) Wall Fixing Slot c) Flow Valve d) Pressure Relief Device (3500M only) n) Relay e) On/Off Solenoid Valve (3500M only) o) Timer PCB f) Pressure Switch p) Start / Stop switch g) Terminal Block x 2 q) Inlet filter...
- Page 14 Cat No. 93672134 Ø25mm Riser Rail Brackets Cat No. 93672160 Ø22mm Riser Rail Brackets Cat No. 93672133 Please Note:- This information shows how our products pass relevant European Union Energy Directives (ErP) Manufacturer Galaxy AQ35M8 AQ35M9 AQ35M10 Product AQ3M8 AQ3M9...
- Page 15 WARNING: KNOB ALIGNMENT IS VERY IMPORTANT DURING THE INSTALLATION OF YOUR SHOWER AND MUST BE CORRECT PLEASE SEE BELOW AND DETAIL ON PAGE 6 Ensure power select Knob is aligned to the ‘cold’ graphic (9 o‘clock position), whilst the ‘Flat’ in the product is aligned as shown (figs.7). Ensure temperature Knob is aligned to cold graphic, fully...
- Page 16 GUARANTEE Terms and Conditions for UK (outside UK contact your local distributor) In the unlikely event of a product breakdown during the guarantee period you should contact our Service and Repair Helpline who will be able to assist with the repair and advise of the best course of action to be taken.