Onset Computer Corporation HOBO H22 Connection Instructions

Veris differential pressure transducer, data nodes

Advertisement

Veris Differential Pressure Transducer Connection Instructions
For use with HOBO
®
Applies to these Veris Differential Pressure Transducers:
Onset Part No.
Air Pressure Range
T-VER-PX3UL
0-10" WC
This document provides instructions on connecting the Veris Differential Pressure
Transducer listed above to each of the following:
FlexSmart
Analog Module used with HOBO H22 series data loggers
Analog Sensor Port/Module used with HOBO U30 and RX3000 series data
loggers
Voltage adapter used with the U12 and UX120-006M data loggers and ZW series
data nodes
It also lists configuration values used by HOBOware
each transducer. Note: For information on connecting the differential pressure transducer
to the pressure source, and other transducer details, refer to the documentation provided
by Veris.

Required

Selected Veris Differential Pressure Transducer
HOBO H22, U12, U30, UX120-006M, or RX3000 data logger, or HOBO ZW data node
FlexSmart Analog Module, Onset Part No: S-FS-CVIA (for H22 series); Analog Sensor Port/Module option (for U30 and
RX3000 series); voltage adapter, Onset Part No. CABLE-ADAP5 or CABLE-ADAP10 (for U12, UX120-006M, or ZW
series)
HOBOware software, version 2.2.1 or higher (2.4.0 or higher for U30 series; 3.6 or higher for UX120-006M);
HOBOware Pro 3.0 or higher for ZW series
HOBOlink (for RX3000 series data loggers)
Customer-supplied length of 18 AWG, shielded, multi-conductor cable
Connecting the Differential Pressure Transducer to the Analog Module or Port
© 2018 Onset Computer Corporation. All rights reserved. Onset, HOBO, HOBOware, and HOBOlink are registered trademarks and FlexSmart is a trademark of Onset
Computer Corporation. Other products and brand names may be trademarks or registered trademarks of their respective owners.
22415-B
H22, U12, U30, UX120-006M, and RX3000 data loggers and HOBO ZW data nodes
Output
4-20mA (or 0-5V/0-10V) representing 0 to 10" WC
®
software to configure the logger for
Veris Part No.
PX3ULX05
Veris Differential Pressure Transducer

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HOBO H22 and is the answer not in the manual?

Questions and answers

Summary of Contents for Onset Computer Corporation HOBO H22

  • Page 1 Connecting the Differential Pressure Transducer to the Analog Module or Port © 2018 Onset Computer Corporation. All rights reserved. Onset, HOBO, HOBOware, and HOBOlink are registered trademarks and FlexSmart is a trademark of Onset Computer Corporation. Other products and brand names may be trademarks or registered trademarks of their respective owners.
  • Page 2 Veris Differential Pressure Transducer Connection Instructions U30 or RX3000 Connection (U30 Shown) Page 2 of 3...
  • Page 3 Veris Differential Pressure Transducer Connection Instructions ZW, U12, and UX120-006M Connection HOBO ZW Series Wireless Data Node; U12 or UX120-006M Logger (ZW shown) Configuring the Data Logger for the Differential Pressure Transducer using HOBOware Software HOBOware software provides configuration files for the transducers. The table below lists the recommended configuration values that these files contain.

This manual is also suitable for:

Hobo u12Hobo u30Hobo ux120-006mHobo rx3000Hobo zw

Table of Contents