Summary of Contents for Oliver 7155
- Page 1 7155/7165 Cyclone Dust Collector Owner’s Manual Oliver Machinery M-7155/7165 09/2011 Seattle, WA Copyright 2003 info@olivermachinery.net www.olivermachinery.net...
-
Page 2: Safety Rules
IMPORTANT SAFETY RULES Wood working can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain hazards involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury. -
Page 3: Safety Rules
IMPORTANT SAFETY RULES FOR DUST COLLECTORS WARNING: Basic precautions should always be followed when using your dust collector. To reduce the risk of injury, electrical shock or fire, comply with the safety rules listed below: 1. READ and understand the instruction manual before operating the dust collector. 2. -
Page 4: Grounding Rules
GROUNDING INSTRUCTIONS The appliance must be grounded, if it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having equipment-ground conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. -
Page 5: Table Of Contents
Do Not Operate This Unit Without Dust Collection Hose or Pipe is installed onto the dust collection inlet port! Specifications 7155 7165 Motor 3HP, 1 Phase 5HP, 1 Phase or 3 Phase Amps 28 or 18 Air Flow Volume CFM... -
Page 6: Unpacking Contents
UNPACKING & CHECKING CONTENTS: A: Main Housing H: Upper Stand O: Hardware Pack B: Cannister Housing I: Lower Stand P: Handle C: Reducing Connector J: Inlet Q: Wheel D: Hose K: Polyester Bag R: Quick Lever E: Drum Lid L: Bag Clamp S: Cannister F: Upper Drum M: Bag Clamp... -
Page 7: Hardware Package
Hardware package: Description Specification Q’TY Part List No. Flange Bolt 5/16”*1/2” NO.17 Flange Bolt 5/16”*3/4” NO.64 Phillip Head Screw 3/16”*3/8” NO.63 5/16” NO.65 Open Wrench 10*12 NO.68 Flat Head Screw 1/4”*5/8” NO.13... -
Page 8: Assembly
ASSEMBLY INSTRUCTION: (Fig.A) (Fig.B) (Fig.C) Step 1-1.1 Open the package and take out the foam. (See Fig.A) Step 1-1.2 Stick the foam around the reducing collector flange. (See Fig.B) Step 1-1.3 Use a screwdriver to make a hole through the foam to allow the Hex. Head bolts through. (See Fig.C) STEP 1-2. - Page 9 Step 1-5. Tape the foam on the bottom of the upper collecting drum. See (Fig.E) (Fig.E) STEP 2-1. Lift the machine up. CAUTION!!! The main housing set is heavy, please have at least 4 people working together to lift it up!!! Place the inlet (22) on the main housing inlet and secure with the Phillip head screw.
-
Page 10: Assembly
STEP 4-1 Attach the switch (48) with plate to the main housing with flat head screw (42). Attach the quick lever set (50) to the main housing with flange bolts and to the drum lid with nut (51). See (Fig.4) (FIG.4) All the assembly steps are completed. -
Page 11: Exploded Parts Diagram
EXPLODED DIAGRAM----... -
Page 12: Parts List
Part List Description Specification Q’TY Lower Collecting Drum Upper Collecting Drum Drum Lid Drum Clamp Phillip Head Screw 1/4”X2” Lower Stand Upper Stand Rod Kit ψ12＂X120 Hose Clamp 12-1/2” Reducing Connector Handle Flat Head screw 1/4”X5/8” PC Board Rivet Copper Screw 3/16”X3/8”... - Page 13 Washer 5/16”X23X1.5T Motor Lower Fixing Plate 5/16” Switch Plate Phillip Head Screw 1/4”X1/2” Phillip Head Screw 3/16”X1/2” Support Set Ball Bear Fixing Plate Ball Bearing 1206 Phillip Head Screw M5X10 Power Cord Switch Set Screw M5X5 Quick Lever Polyester Bag Bag Clamp CK500 Canister...
-
Page 14: Warranty
Oliver makes every effort possible to assure that its equipment meets the highest possible standards of quality and durability. All products sold by Oliver are warranted to the original customer to be free from defects for a period of 2 (two) years on all parts, excluding electronics and motors, which are warranted ear Ol er’s...