1. Manuals
  2. Brands
  3. Thinklogical Manuals
  4. Network Hardware
  5. SCS80
  6. Product manual

Thinklogical SCS80 Product Manual

Secure console servers
Hide thumbs
Table of Contents

Advertisement

Quick Links

Secure Console Servers
SCS, SCS-R and Sentinel Models
Product Manual
Thinklogical, LLC
®
100 Washington Street
Milford, Connecticut 06460 U.S.A.
Telephone: 1-203-647-8700
Fax: 1-203-783-9949
www.thinklogical.com
Revision K, July, 2013

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SCS80 and is the answer not in the manual?

Questions and answers

Summary of Contents for Thinklogical SCS80

  • Page 1 Secure Console Servers SCS, SCS-R and Sentinel Models Product Manual Thinklogical, LLC ® 100 Washington Street Milford, Connecticut 06460 U.S.A. Telephone: 1-203-647-8700 Fax: 1-203-783-9949 www.thinklogical.com Revision K, July, 2013...
  • Page 2 All trademarks and services marks are property of their respective owners. Appendix C copyright © 2003, by Multi-Tech Systems, Inc. Subject: SCS80 / SCS160 / SCS320 / SCS480 / SCS80R / SCS160R / SCS320R / SCS480R / Sentinel 32 Revision: K, July 2013.

  • Page 3: Table Of Contents

    1.5 Technical Specifications 1.6 Documentation 2. Product Overview 2.1 Intended Application 2.2 System Chassis 2.2.1 SCS80 / SCS160 / SCS320 / SCS480 2.2.2 SCS80R / SCS160R / SCS320R / SCS480R 2.2.3 Sentinel 32 2.3 Connecting to the SCS 2.3.1 Serial Devices 2.3.1.1 Break Safe...
  • Page 4 3.4 SCS-R and Sentinel -48VDC Power Modules 3.4.1 Wiring the -48VDC Connector 3.4.2-48VDC Power Module Replacement 4. Initial Configuration 4.1 Default Configuration 4.2 Initial System Security Concerns 4.3 Front Panel Network Setup 4.3.1 Front Panel Edit Mode 4.3.1.1 Start Front Panel Edit Mode 4.3.1.2 Program Network 4.4 Initial Connection via Network 4.4.1 Network Connection Requirements...
  • Page 5 7.8 Network Time Service 7.8.1 Configure NTP 7.8.2 Start the NTP Service 7.9 NIS and User Port Permissions 7.9.1 User Port Control 7.9.2 NIS Port Access 7.9.3 User Names and Groups 7.9.4 NIS Database file 7.9.5 NIS Make file 7.9.6 NIS Configuration File 7.10 NFS 7.10.1 Remote NFS Directory 7.11 SNMP...
  • Page 6 10.2.2.3 Supplemental Information 10.3 Product Serial Number 10.4 Lithium Battery 10.5 SCS-R Models and Sentinel 32 Power Modules 11. How to Contact Us 11.1 Customer Support 11.1.1 Website 11.1.2 E-mail 11.1.3 Telephone 11.1.4 Fax 11.2 Product Support 11.2.1 Limited Warranty Information APPENDICES File System Sentinel 32 Modem Commands...

  • Page 7: Preface (Notes & Warnings)

    1. Introduction This document pertains to the Secure Console Server (SCS) line of products developed and built by Thinklogical , Inc. of Milford, Connecticut, USA and covers ® the installation, configuration and operation of all SCS models. This document also covers User and Administrator Operations, Regulatory &...
  • Page 8 The SCS80R, SCS160R, SCS320R and SCS480R models are designed with dual hot- swappable Power Modules which operate redundantly and two network ports and console port connections. The ‘R’ models are otherwise similar to the SCS80, SCS160 and SCS320. SCS80R - 8-Port 1U Redundant Power •...
  • Page 9 The following SCS models are available for International customers and are shipped with regionally appropriate power cord sets. Otherwise, each international model is similar to the domestic SCS80 / SCS160 / SCS320 / SCS480 / SCS80R / SCS160R / SCS320R / SCS480R and Sentinel 32 models.

  • Page 10: System Features

    1.2 System Features Each SCS system includes the following features: • Linux operating system and command set • Connections for up to 16, 32 or 48 EIA-232 serial console ports • 10 baseT/100 baseTX network compatibility • Pre-configured from the factory: User ready, right from the box •...

  • Page 11: Scs80R, Scs160R And Scs320R Hardware

    The SCS can help troubleshoot your networking environment. The SCS is a "listening" system that monitors messages (ASCII data, server error information, etc.) from the serial ports of the device to which each Port is connected. The SCS captures the data by writing it to a port buffer that can hold 256K bytes of data per port. This buffered data gives the sysadmin a history of console port messages that can be reviewed for troubleshooting a connected device.

  • Page 12: Technical Specifications

    Backlit 2-line front-panel LCD display showing network User Interface configuration. Five front-panel push buttons with UI for network setup. SCS80/SCS80R = 8 Ports; SCS160/SCS160R = 16 Ports; SCS320/SCS320R/Sentinel 32 = 32 Ports; SCS480/SCS480R = 48 Ports. Serial Interface RJ45-type 8-conductor connector (DTE or DCE; software selectable).

  • Page 13: Documentation

    48 of your networking systems (servers, routers, switches, etc.). They do so by monitoring the console port of your network center’s devices and systems. Each attached component must have an EIA-232 compatible serial port. The SCS80 and SCS80R support 8 ports, SCS160 and SCS160R support 16 ports, SCS320, SCS320R, and Sentinel 32 support 32 ports and the SCS480 and SCS480R support 48 ports.

  • Page 14: System Chassis

    Removable 3-position rack mount brackets are provided. The front panel of the SCS features a two-line, backlit LCD display with five user buttons. 2.2.1. SCS80 / SCS160 / SCS320 / SCS480 Each SCS chassis has rear-panel connections for 8, 16, 32 or 48 serial ports, one console port, one network port and power input.

  • Page 15: Serial Devices

    Each port may also be assigned a unique name: default port names are port1, port2, etc 2.3.1.1 Break Safe Thinklogical SCS systems are “break-safe,” meaning they will not send a “break” command ® or other data on the serial ports connected to your servers unless initiated by a user. An unwanted “break”...

  • Page 16: Ac Power

    Only the first port (NETWORK 1) is enabled by default. 2 .3. 3 AC P ow er 2.3.3.1 SCS80 / SCS160 / SCS320 / SCS480 A single IEC-type Power Entry Module is located on the rear of the chassis. The power entry module incorporates a replaceable protective fuse (2A) and an On/Off switch.

  • Page 17: User Sessions

    2.4.1 User Sessions Each SCS supports up to 250 simultaneous user sessions. 2.5 Port Buffers Thinklogical Secure Console Servers provide real-time serial port data buffering. Each ® port buffer stores up to 256KB of data held in a separate RAM file for each attached device.

  • Page 18: Front Panel Display And Buttons

    3.1.2 Front Panel Display and Buttons The front-panel LCD display should be visible and accessible during system setup. It typically displays the current network settings and the date/time. The front panel buttons are only used during setup or to review existing SCS settings. The LCD display can be customized by the root user.
  • Page 19 Replace with same type and rating fuse. NETWORK NETWORK CONSOLE MODEM PORTS 100-240V -, 0.5A, 50/60 Hz T2A, 250 VAC SCS80 Secure Console Server CAUTION! Replace with same type and rating fuse. NETWORK www.thinklogical.com CONSOLE PORTS 100-240V -, 0.5A, 50/60 Hz...

  • Page 20: Power

    3.2.1 Power SCS products have an internal universal Power Supply. Each SCS unit requires approximately 15W of electrical power. The switching power supply accepts nominal AC input voltage between 100-240 VAC with a frequency range of 50-60 Hz. Note: The optional -48VDC Power Module is described in Section Appendix D, DC Power, on page 83.

  • Page 21: Connect Your Console

    3.2.4 Connect Your Console The console port is used for local access to the SCS. Connect your terminal or computer to the console port with a terminal emulation package. The SCS’s console port has a DCE configuration with adjustable parameters. The default communication parameters for the console port are: •...

  • Page 22: Automated Port Configuration Tests

    A man page exists for pm. This can be used to troubleshoot SCS to server connections. Hardware signals from the server are tested but Baud rates are not. 3.2.5.2 Port Adapters You may need to adapt the cable connection for your server device. Thinklogical offers serial- ®...

  • Page 23: Scs-R And Sentinel Power Modules

    3.3 SCS-R and Sentinel Power Modules The SCS80R, SCS160R, SCS320R, and Sentinel 32 provide dual AC Power Modules which are field-replaceable and connect to the rear panel of the SCS chassis. Each Power Module has a power entry connection with an IEC-type power connector. The SCS80R, SCS160R, SCS320R, and Sentinel 32 have a power monitoring display shown on the front panel to indicate if one of the power supplies is not powering the system (either AC power failure, a Module is turned off or the supply has failed).

  • Page 24: Scs-R And Sentinel -48Vdc Power Modules

    Captive Mounting Screw Handle AC Power Module (removed from SCS Chassis) SCS80R, SCS160R, SCS320R and Sentinel 32: If the front panel display indicates that one of the power supply modules has failed, it may need to be replaced. A single captive screw (visible from the rear of the SCS80R, SCS160R, SCS320R or Sentinel 32 chassis) holds the Power Module in place and also establishes a protective Earth ground.

  • Page 25: Wiring The -48Vdc Connector

    The SCS480R Power Module is mounted in the front panel of the SCS480R and has the same capabilities as the SCSR and Sentinel Modules. It is not necessary to remove the DC power cord from the SCS480R when replacing a module. Note: The Power Modules in the SCS160/320/480 are NOT FIELD SERVICEABLE.

  • Page 26: 2-48Vdc Power Module Replacement

    3.4.2 -48VDC Power Module Replacement The Power Modules of the SCS-R and Sentinel 32 Models may be hot-swapped if necessary. Each slide-in Power Module is held in place with a single screw and does not need to be removed except for replacement. -48VDC Power Module and WAGO Connector (shown removed from Sentinel 32) SCS80R, SCS160R, SCS320R, and Sentinel 32: If the front panel display indicates that one of the power supply modules has failed, it may...

  • Page 27: Initial Configuration

    4. Initial Configuration The SCS is Pre-Configured. Just set your IP Address and add Users. 4.1 Default Configuration The SCS is pre-configured right out of the box, ready to generate ssh keys with an IP address set to a generic default value of 10.9.8.7 / NetMask 255.0.0.0. It is likely that the sysadmin will want to change to a local IP address.

  • Page 28: Start Front Panel Edit Mode

    With Edit mode enabled, use the arrow buttons on the front panel to access the front panel edit subroutine and change the default network settings (showing the IP address Netmask and Gateway) for your SCS system. The front panel controls are self-prompting for the appropriate entries.
  • Page 29 Network IP Address SCS Front Panel Display for Network Programming mode Press the Enter button to continue. SCS Front Panel Display showing the current IP Address The current IP Address will be displayed with leading zeroes. The factory default is 10.9.8.7. If you do nothing, the display will revert to the previous display after 30 seconds and no changes will be made.
  • Page 30 When the address input is complete, press the Enter button to accept the entry. The display will look like the following example: SCS Front Panel Display after editing the IP Address The new value will be stored when you finish setting all the Network parameters. Net Mask Press the Down Arrow once to advance to the Net Mask parameter.
  • Page 31 The new value will be stored when all the Network parameters are set. Gateway You may now enter your Gateway parameter information. Press the Down arrow once to continue. SCS Front Panel Display showing the current Gateway setting Press the Enter button to edit the Gateway parameter. The current Gateway setting will be displayed with a cursor under the first digit.
  • Page 32 Exit to Main Menu You will now be prompted to Exit to the Main Menu. Press Enter to continue. SCS Front Panel Display exiting the LCD Mode You are given the choice to Save your changes or to Cancel them. SCS Front Panel Display to Save or Cancel Changes Press Enter to save your network changes or press the Up arrow to discard them.

  • Page 33: Initial Connection Via Network

    4.4 Initial Connection via Network You can access the SCS using ssh (secure shell host) commands with your existing net- work. If you add a route to your workstation, you can connect to the SCS via its default address. For security reasons, a telnet server is not active on the SCS. 4.4.1 Network Connection Requirements •...
  • Page 34 command is a way to verify a network connection.) Type ping 10.9.8.7 at the DOS prompt, then press Enter. Check for a completed connection. Connect to the SCS with your terminal package using ssh. Launch your terminal package and connect to the default IP address of the SCS of 10.9.8.7 using ssh. If using PuTTY (shown below), set the Session window IP address to 10.9.8.7, select the ssh radio button and press Open.

  • Page 35: Initial Connection Via Console Port

    GPL by reviewing the text version of the GPL at http://www.gnu.org/licenses/gpl.txt. You will find additional GNU license information online at: http://www.gnu.org/licenses/licenses.html#GPL. Please contact Thinklogical Product Support (1-203-647-8700 or toll-free at 1-800- ® 291-3211) if you need a copy of this source code.

  • Page 36: Initial System Administrator (Sysadmin) Access

    5.2 Initial System Administrator (sysadmin) Access When the SCS is first powered up, you may need to configure it to operate with your network. Use ssh to access the SCS or the local console (Section 3.2.4, Connect Your Console, on page 21).
  • Page 37 In order to configure the basic services, you must: Run some or all of the following: (netconfig, changehostname, timeconfig, authconfig). Run save Run service network restart to restart the network. To configure the existing features, use the following commands: For the Network parameters, use netconfig •...

  • Page 38: Commands

    6 . C o m m a n d s A summary of special SCS Commands 6.1 System Commands SCS products use Linux commands and man pages are available for all system commands. The root user can access the following commands to configure the special features of the SCS: COMMAND PURPOSE CHPT.

  • Page 39: Poweroff

    Use man <command name> to search for a help file (online manual pages) or descriptive information for that Linux / UNIX command. Three general man pages are available for Thinklogical commands and files: lsi.1 for user commands lsi.8 for system commands 3.
  • Page 40 sftp Use sftp for a secure file transfer transaction between two servers using ssh. This process is similar to ftp except that it is encrypted for security. Refer to the man pages for sftp for a description and any command options. The SCS systems use ssh to establish secure connections over your network.

  • Page 41: Change Logging Level

    This section outlines the administration functions and commands that are accessed using the network or console ports. 7.1 Security Thinklogical Secure Console Servers use ssh to provide encryption for a secure network ® connection. There is only one level of system administration access in the SCS and that is at the root level.

  • Page 42: Save Your Netconfig Changes

    You will need the following information before running netconfig Using DHCP/BOOTP (yes/no)? If No, you will need the following: • IP Address • Net Mask • Default Gateway • Primary Nameserver • You can add the secondary and tertiary nameservers (if required) by editing the resolv.conf file at any time.

  • Page 43: More Than One Nameserver

    7.2.2 More Than One Nameserver The netconfig command allows the user to set up one nameserver’s IP address. It is possible to have multiple nameservers, which must be done outside of the netconfig command. The nameserver data is in the file /etc/resov.conf If you want to have more than one nameserver, you must edit the file For more information, refer to the man page...

  • Page 44: Configure Authentications

    This file already has the various commands in place, but they are commented out (rendered inactive by the preceding #). Edit the /etc/modules.conf as required. Remove the leading # from one of the #options lines below to make it active, then reload the NIC driver. alias eth0 eepro100 alias char-major-72 exser alias char-major-4 off...

  • Page 45: Display Mode Parameters

    Default Front Panel Display, The front panel will display system messages during events such as reboot or save, but will return to the default display following these events. 7.7.1 Display Mode Parameters The various LCD Display modes are controlled by entries maintained in the file: /etc/sysconfig/lsi •...

  • Page 46: Display Off

    LINE_2 Changed in SCS Front Panel Display 7.7.1.5 Display OFF disables the front panel LCD display when no events are taking place. The LCD_DISPLAY=OFF backlighting will remain on, but the display is blank. 7.8 Network Time Service Network Time Service is supported. To use the network time service, the user must edit the files /etc/ntp.conf and /etc/ntp/step-tickers and start the ntpd service as described in the following paragraphs.

  • Page 47: User Port Control

    7.9.1 User Port Control The SCS can use NIS to control which user can access a port on the SCS. To use this feature, a database must be created on the NIS server. The following files are needed to set up the port access database: Port Access Permission Definition file lsi_port_access...

  • Page 48: User Names And Groups

    7.9.3 User Names and Groups The LSI Port User Definition file (/nis/lsi_port_users) is used to assign a user to a given Port Access group. This file information is found in /usr/local/doc/nis. The following example illustrates how it is set up: User name:group name where: user name is a valid SCS user group name is a valid users’...

  • Page 49: Nis Configuration File

    7.9.6 NIS Configuration File The NIS configuration file (located at /etc/nsswitch.conf) must be edited by the user to support your NIS server. To do this: Open the file /etc/nsswitch.conf using your editor. Edit (add or modify) a line to your config file that supports local files for local users and, if not assigned locally, refers to the NIS database.

  • Page 50: Snmp

    7.11 SNMP Simple Network Management Protocol (SNMP) governs network management and the monitoring of network devices and their functions. Network management stations monitor and control the network components. SNMP is supported in the SCS as “read only”. Refer to the man pages for more details.

  • Page 51: Administering Users

    8. Administering Users The following commands are used to change settings for users. You can define as many users as you wish, up to the memory capacity of the system. The limiting factor for users is not the number of users but the number of simultaneous sessions invoked by any number of users (250 sessions maximum).

  • Page 52: Edituser

    8.1.2 edituser The edituser command is used to change the parameters for an existing user. The user name cannot be edited using edituser n order to modify a user’s name you must generate a new user account and enter the appropriate assignments. You should then delete the original user account (paragraph 8.1.3).

  • Page 53: Port Identities

    Ports. There is only one root user for each SCS system. The root user defines the access rights of all users in the SCS system. The root user’s access is secured with the root password (default password is root). The root password should be changed regularly and carefully guarded to prevent unauthorized access.

  • Page 54: Escape Sequence

    editbrk When not in the Interactive mode, a user can enter editbrk to edit or view their preset break sequence. The break sequence is presented in its ASCII form (x1bB). The user key stroke default is <ESC>B. Press Enter to keep the existing setting. Warning!: Because the sysadmin is responsible for configuration changes, it is recommended that only the sysadmin be allowed to change the break sequence.

  • Page 55: Regulatory & Safety

    • Industry Canada ICES-003 Issue 2, Revision 1 10.2.2 European Union 10.2.2.1. Declaration of Conformity Product name Model: SCS80 Secure Console Server, SCS801 Secure Console Server • Model: SCS160 Secure Console Server, SCS1601 Secure Console Server • Model: SCS320 Secure Console Server, SCS3201 Secure Console Server •...

  • Page 56: Supplemental Information

    Electromagnetic Immunity EN55024:1998 Information Technology Equipment-Immunity Characteristics • EN61000-4-2:1995 Electro-Static Discharge Test • EN61000-4-3:1996 Radiated Immunity Field Test • EN61000-4-4:1995 Electrical Fast Transient Test • EN61000-4-5:1995 Power Supply Surge Test • EN61000-4-6:1996 Conducted Immunity Test • EN61000-4-8:1993 Magnetic Field Test •...

  • Page 57: Lithium Battery

    11.1.1 Website Visit our website at www.thinklogical.com for more product information, current updates and the full line of Thinklogical products. Our internet website offers product information on all ® current systems, including technical specification sheets and Quick Start Guides (for viewing online or for download), product diagrams showing physical connections and other useful information.

  • Page 58: Email

    This limited warranty does not cover defects resulting from (i) use of the product other than as described in the applicable documentation for the product; (ii) modifications to or repairs of the product that are made by any party other than Thinklogical or a party acting on ®...
  • Page 59 If repair or replacement is not possible, Thinklogical may keep the defective product and ® refund the amount that you paid for the defective product. These are Thinklogical’s sole ® obligations, and your exclusive remedies, for a breach of the limited warranty set forth above.

  • Page 60: A File System

    Appendix A: File System A.1 Read-Only vs. Read-Write In some instances you may need to interact directly with the SCS’s file system, in which case you must mount it for read-write (R/W) access before changes can be made to the system’s Compact Flash.

  • Page 61: Bfaq

    Ap p en d i x B: F AQ A few frequently-asked questions B.1 How To… This section is a collection of tips and hints for various setup items. The root user can change any of the following features using the given command steps: B.1.1 Change Port Parameters Serial Port settings are modified via the stty command (see man page stty The serial port...

  • Page 62: C Sentinel 32 Modem Commands

    Appendix C: Sentinel 32 Modem Commands The following modem commands information has been extracted, with the permission of the modem’s manufacturer, from the Multi-Tech Systems, Inc., Developer’s Guide (2003). Introduction The AT commands are used to control the operation of your modem. They are called AT commands because the characters AT must precede each command to get the ATtention of the modem.
  • Page 63 Command Description Return Online to Data Mode Pulse Dialing Result Codes Enable/Disable Sr=n Set Register Value Read Register Value Tone Dialing Result Code Format Result Code Options Result Code Selection Modem Reset &Cn Data Carrier Detect (DCD) Control &Dn Data Terminal Ready (DTR) Control &En XON/XOFF Pass-Through &Fn...
  • Page 64 Command Description # CBIn Local Callback Inactivity Timer # CBNy=n Store Callback Password # CBPn Callback Parity # CBRy Callback Security Reset # CBSn Callback Enable/Disable Set 11-bit Parity Enter Setup Password #S=x Store Setup Password +VDR=x, y Distinctive Ring Report +++AT<CR>...
  • Page 65 Return to command mode after dialing. (Place at end of dial string.) Hook flash. Causes the modem to go on-hook for one-half second, then off-hook again. Wait for quiet answer. Causes modem to wait for a ringback, then 5 seconds of silence, before processing next part of command.
  • Page 66 Default: Description: Modem performs handshake only at communication standard specified by S37 and the B command. N1 Modem begins handshake at communication standard specified by S37 and the B command. During handshake, fallback to a lower speed can occur. Command: Return Online to Data Mode Values: 0, 1, 3...
  • Page 67 Default: Description: X0 Basic result codes (CONNECT); does not look for dial tone or busy signal. X1 Extended result codes (CONNECT 46000 V42bis); does not look for dial tone or busy signal. X2 Extended result codes with NO DIALTONE; does not look for busy signal. X3 Extended result codes with BUSY;...
  • Page 68 Values: = 0, 3, or 4 Defaults: Description: &K0 Disable flow control. &K3 Enable CTS/RTS hardware flow control. &K4 Enable XON/XOFF software flow control. Command: &L Leased Line Operation Values: = 0, 1, or 2 Defaults: Description: &L0 The modem is set for standard dial-up operation. &L1 The modem is set for leased line operation in originate mode.
  • Page 69 Command: &V Display Current Settings Values: Description: Displays the active modem settings. Command: &W Store Current Configuration Values: = 0 or 1 Default: Description: &W0 Stores current modem settings in non-volatile memory and causes them to be loaded at power-on or following the ATZ command instead of the factory defaults. See &F command. &W1 Clears user default settings from non-volatile memory and causes the factory defaults to be loaded at power-on or following the ATZ command.
  • Page 70 Command: Error Correction Mode Selection Values: n = 0–5, or 7 Default: Description: \N0 Non-error correction mode with data buffering (buffer mode; same as &Q6). \N1 Direct mode. MNP reliable mode. If the modem cannot make an MNP connection, it disconnects. \N3 V.42/MNP auto-reliable mode.
  • Page 71 Command: View Numbers in Blacklist Values: Description: If blacklisting is in effect, AT%B displays the numbers for which the last call attempted in the previous two hours failed. In countries that do not require blacklisting, the result code ERROR appears. Command: Data Compression Control Values:...
  • Page 72 Command: Online BPS Speed Values: = speed in bits per second Default: 28,800 Description: $MB75 Selects CCITT V.23 mode $MB300 Selects 300 bps on-line $MB1200 Selects 1200 bps on-line $MB2400 Selects 2400 bps on-line $MB4800 Selects 4800 bps on-line $MB9600 Selects 9600 bps on-line $MB14400 Selects 14400 bps on-line...
  • Page 73 Command: #CBAn Callback Attempts Values: n = 1–255 Default: Description: Sets the number of callback attempts that are allowed after passwords have been exchanged between modems. Command: #CBDn Callback Delay Values: n = 0–255 Default: Description: Sets the length of time (in seconds) that the modem waits before calling back the remote modem. Command: #CBF? Callback Failed Attempts Display...
  • Page 74 Command: Set 11-bit Parity Values: n = 0 or 1 Default: Description: #P0 No parity. #P1 Odd parity. #P2 Even parity. Command: Enter Setup Password Values: = password (1–8 characters, case sensitive) Default: MTSMODEM Description: Enters the remote configuration setup password. Command: Store Setup Password Values:...
  • Page 75 Modulation Possible rates (bps) 56000, 54666, 53333, 52000, 50666, 49333, 48000, 46666, 45333, 44000, V903 56000, 54666, 53333, 52000, V.90 50666, 49333, 48000, 46666, 45333, 44000, V.34 33600, 31200, 28800, 26400, 24000, 21600,19200, 16800, 14400, 12000, V32B V.32bis 14400, 12000, 9600, 7200, or 4800 V.32 9600 or 4800 V22B...
  • Page 76 Description: Controls the action to be taken upon detection of a call waiting tone in V.92 mode. Values specified by this command are not modified when an AT&F command is issued. +PCW=0 Toggles V.24 Circuit 125 and collects Caller ID if enabled by +VCID +PCW=1 Hangs up +PCW=2...
  • Page 77 Command: +PMHT=n Modem on Hold Timer Values: = 0–13 Default: Description: Determines if the modem will accept a V.92 Modem on Hold (MOH) request and will set the MoH timeout. +PMHT=0 Deny MOH request +PMHT=1 Grant MOH request with 10 second timeout +PMHT=2 Grant MOH request with 20 second timeout +PMHT=3...
  • Page 78 +VDR=0, n/a Disables Distinctive Ring cadence reporting. +VDR=1, 0 Enables Distinctive Ring cadence reporting. Other call progress result codes (including RING) are reported as normal. +VDR=1, >0 Enables Distinctive Ring cadence reporting. RING result code is reported after falling edge of the ring pulse (after the DRON report). +VDR=? Displays the allowed values.
  • Page 79 #CBS1 Enables local and remote callback security. #CBS2 Enables remote callback security only. #CBS3 Disables callback security until local hangup or reset. Command: Set 11-bit Parity Values: n = 0 or 1 Default: Description: No parity. Odd parity. Even parity. Command: Enter Setup Password Values:...
  • Page 80 0 = maximum speed 1 = reserved 2 = 1200/75 bps 3 = 300 bps 4 = reserved 5 = 1200 bps 6 = 2400 bps 7 = 4800 bps 8 = 7200 bps 9 = 9600 bps 10 = 12000 bps 11 = 14400 bps 12 = 16800 bps 13 = 19200 bps...
  • Page 81 modem will wake on an incoming ring or an AT command. S108 decimal 0–3, 6, 7 Selects the 56K digital loss if using the modem through a PBX line. The default value is -6 dB loss, the value used when calling from a typical POTS line long distance.
  • Page 82 Terse Verbose Description CONNECT 115200 Connected at 115200 bps DELAYED Delay is in effect for the dialed number BLACKLISTED Dialed number is blacklisted BLACKLIST FULL Blacklist is full CONNECT 230400 Connected at 230400 bps CONNECT 28000 Connected at 28000 bps CONNECT 29333 Connected at 29333 bps CONNECT 30666...

  • Page 83: Ddc Power

    Appendix D: DC Power D.1: Assembly of the WAGO MCS DC Power Connector What you will need: Small flat-blade screwdriver, Wire stripper, DC power connector kit (provided with DC models), 48 VDC power cord (See Step 2, below and Appendix D.3) WAGO MCS DC power connector: 1.
  • Page 84 WAGO MCS DC power connector -48VDC Power Supply (removed from back panel) Input voltage: -48VDC Minimum voltage: -40 VDC Maximum voltage: -60 VDC Maximum operating current: 0.5A The DC power source must be: • Electrically isolated from any AC source •...

  • Page 85: E Assigning Ip Addresses To A Device Port

    The cable type should be one of the following: • UL style 1028 or other UL 1581 (VW-1) compliant equivalent • IEEE 383 compliant • IEEE 1202-1 991 compliant Appendix E: Assign an IP Address to a Device Port Version 1.7-9 of the SCS software can assign an IP address to the SCS’s device ports. The user can use ssh to access a port directly without having to first login to the SCS.
  • Page 86 ADP-000005 RJ45 to 25-pin Male ADP-000006 RJ45 to 25-pin Female 25-pin RJ45 Wire key: 1-Blue 2-Orange 3-Black 4-Red 5-Green 6-Yellow 7-Brown 8-White RJ-45 S e c u r e C o n s o l e S e r v e r M a n u a l , R e v . K , J u l y , 2 0 1 3 Page 86...
  • Page 87 ADP-000007-R RJ45 to DB9 Male ADP-000008-R RJ45 to DB9 Female RJ-45 Wire key: 1-Blue 2-Orange 3-Black 4-Red 5-Green 6-Yellow 7-Brown 8-White RJ- 45 Jack ADP-000007- R Pin 1 DB9 Male S e c u r e C o n s o l e S e r v e r M a n u a l , R e v . K , J u l y , 2 0 1 3 Page 87...
  • Page 88 ADP-000009 RJ45 to 25-pin Male ADP-000010 RJ45 to 25-pin Female 25-pin RJ45 Wire key: 1-Blue 2-Orange 3-Black 4-Red 5-Green 6-Yellow 7-Brown 8-White RJ-45 S e c u r e C o n s o l e S e r v e r M a n u a l , R e v . K , J u l y , 2 0 1 3 Page 88...
  • Page 89 ADP-000011-R RJ45 to DB9 Male ADP-000012-R RJ45 to DB9 Female RJ-45 Wire key: 1-Blue 2-Orange 3-Black 4-Red 5-Green 6-Yellow 7-Brown 8-White RJ- 45 Jack ADP-000011- R Pin 1 DB9 Male S e c u r e C o n s o l e S e r v e r M a n u a l , R e v . K , J u l y , 2 0 1 3 Page 89...

  • Page 90: G Quick Start Guide

    Appendix G: Quick Start Guide S e c u r e C o n s o l e S e r v e r M a n u a l , R e v . K , J u l y , 2 0 1 3 Page 90...

This manual is also suitable for:

Scs160Scs80rScs480Scs160rScs320Sentinel 32 ... Show all

Table of Contents