Advertisement
e
OPERATING MACHINE IN SELECTED MODES
1.
Point
the
remote controller
at the unit,press the ON/OFF button, then press
the MODE button,select
the
needed
mode: ATUO,COOL,DRY,HEAT,or
FAN.
2.
Press the SET TEMPERATURE button to
increase or
decrease the readings
until the needed temperaure
is
displayed.
The room set
temperature range
is
from
16'C-32'C(61'F-90'F).
(It
would
be
automatically
set
at 25'C(76'F)
and
unadjustable in
AUTO
and
DYR
mode.)
3. Press the
FAN
SPEED
button to choose the air
rate
you want: Low(
display
indicates" '""),Med(display
indicates
"
,..
",Hi(display
indicates"
•
d
",Auto(
display"•
~I
"indicator
flashing).
(It
would
be
automatically
set
allow speed and
unadjustable in
DRY mode.)
4.
Press
the SWING
button
to
choose
the
up/down air
flow
direction
you
want:natural
flow( display
indicates
"
(
"),swing(
display"
(
• indicator
flashing)
,fixed
wind( display
indicates •
:
").
(It would be automatically set
at
fixed wind
air
flow
direction in
DRY
mode.)
e
TURBO OPERATION
Press TURBO button
during
COOL
or
HEAT
operation,the air
rate
can
be
setted
in HIGH .Press
the
TURBO button
again
can
release
the TURBO
operation.
Nole:
during
TURBO
operation,the
air
rate
cann't
be
changed.
eADJUSTING LEFT/RIGHT AIR
FLOW
Methods 1 :Manually
adjust
Adjust
the
direction
by
moving direclly
the
lefVright
air flow.direction adjusting
fin by
hand.
Caution:when
adjust the direction,stop
air conditioner.
Methods
2:Horlzontal
&
vertical
auto
swing(three-dimenslonal
air
flow model)
Adjust
the direction by
remote
controller.Press
the
AIR
FLOW
button,the
air swinging
fins
will
constantly
make the
lefVright
swinging or
fixed
direction
in
air
delivery.
e
TIMER OPERA T/ON
Set turning off time
Set
the
time
for the unit to turn off
and when
it
is
time,the
air conditioner
will
automatically stop operating.
1.
During
the operation of
the
air conditioner,
press
the TIMER button
and
the air conditioner
will
enter the
timed
switch-off
mode.
2.
Continuely
press
the
TIMER
button
to
set the needed time for switching off the machine. The
timer
can
make
the
setting
in
the
range
from
1-24
hours.Every the
button
is
pressed,indication
change
is
the
following
sequence:
1
-
2
-
........
-
24
-
cancel
(no
indication)-
1.
3.
After the setting of the timed
switch-off,
the
digits shown on the display
screen
w~l
go
down by
1
for every
elapsed
hour.
The
displayed digits indicate
the
remaining
time prior to the timed
switch-off.
Set turning on time
Set
the
time for the
unit
to
turn
on
and
when
it
is
time, the
air
conditioner
will
automatically start operating.
1.
When
the air conditioner is
in
the standby mode, press the
TIMER
button
and
the air conditioner
will enter
the
timed
switch-on mode.
2.Continuely
press the
TIMER button
to set
the
needed time for switching on the
machine. The
timer
can make
the
setting
in the
range
from
1-24
hours.Every
the
button
is
pressed,indication change
is
the
following
sequence:
1
-
2
-
........ -
24
- cancel
(no
indication)-
1.
3. After
the
setting of
the
timed
switch-on, the digits shown on the display screen will go down
by 1
for every elapsed
hour. The
displayed
digits indicate
the
remaining time prior to
the timed
switch-on.
-10-
,
,
Releasing procedure
When
the
indication on display
screen
is 24
hour,press
the TIMER
button
again
to delete
the
timed
mode.
e
SLEEP OPERATION
Use
this
mode to reduce operation sound when sleeping,etc.
Press
the
SLEEP
button,the air
flow sound
from the
indoor
unit
is
decreased.
Press
the
SLEEP
button
again
can
release
the
mode.
NOTE:
•
Use
the sleep
mode
when
you
are
going
to
bed.
If
this mode
is used
in the
day,the
capacity
is
reduced
since
the
ambient temperature is too
high.(COOL
MODE).
•
During the operation of cooling,the room temperature
will
be raised gradually by
2"C(4'
Fl
higher
than
the setting
after the
machine begins to
operate in
the
sleeping
mode.
•
During
the
operation
of
heating
mode,the
room temperature
will
be
dropped
gradually
5'C (9'F)Iower than
the
setting
after
the
machine
begins
to operate
in
the
sleeping mode.
e
REPLACEMENT
OF BATTERIES
•
When
the
signal
from the
remote
controller
becomes
weak
and
the
indoor
unit can
not receive
it
properly;or the indications on the display
screen
becomes blurred,please slide
the
back cover and replace with
two
new
batteries.
• The
positive
and
negative
poles must
match
the
i
n
stallation
positions.
•
New
batteries of
the same
type
have to
be
used for
replacement.
•
If
the
remote
controller
is
not
to be
used
for
long
time,take
out
the
batteries
so as
to
prevent
the
leakage of the electrolyte from damaging
the
controller.
•
If when
the remote controller
is
at
abnormal
state,you can take out
the batteries on
the
back cover to clear off the
display.
-1
1-
Remote
Controller 2,4
Unload
the back
Ower
Remote
Controller 1,3
Advertisement
