Warmtec T510 Installation Manual

T510 Weekly Programming Thermostat with LCD Screen
Weekly Programming Thermostat with LCD Screen
Weekly circulation , it is possible to set 6 periods called events each day with
different temperatures, also you can select "manual mode" or " temporary
control mode" according to your individual requirements. The thermostat is
recommended for the control of electric heating devices or on/off valve actuator
used in water - based heating systems .
Technical data:
Voltage : AC230V (AC110V/AC24V available)
Power consumption : 2W
Setting range : 5℃~90℃
Limitation range : 5℃~99℃ (factory setting : 35℃)
:0.5℃~10℃ (factory setting : ±1℃)
Switching differential
Ambient temperature : -5℃~50℃
Protective housing : IP20
Housing material : self-extinguishing PC
Daily use of the thermostat
1） on/off " "
2） In the manual mode ，press "
3） Press " " or" " to increase or decrease pre
4） Pre ss " " and " "and hold for 5 seconds at the same time to adjust
time. Press " " to choose object to adjust; Press"
increase or decrease your set values; Press " " to confirm and exit.
5） Press the " " key to select manual mode or clock -controlled program
mode.
6） It displays the time or the preset temperature alternately, and it displays
the measured temperature directly.
7） When you press " " and " "at the same time and hold for 5 seconds,
the thermostat will be locked/unlocked. When it is locked, no operation
can be carried out until it is unlocked.
Display symbols ：
Manual mode
Period control mode
Heating
Getting up, the first period
Out in the morning, the second period
Going home at noon, the third period
Out in the afternoon, the forth period
Going home in the evening, the fifth period
Sleeping at night, the sixth period
Period programming
Press " " and hold for 5s to enter the mode of Period programming.
Key Period Symbol
1
2
3
4
5
6
1
"to make temporary control 。
" or"
- set temperature.
" or "
Time
Tempe rature
06:00 20℃
08:00 15℃
11:30 15℃
12:30 15℃
17:00 22℃
22:00 15℃
www.warmtec.pl
WARMTEC Sp. z o.o., Al. Jana Pawła II 27, 00-867 Warszawa
1
2
Advanced setting (qualified person preferred )
When the thermostat is turned off, You can press"
same time ,then you can enter the mode of advanced setting.
Symbol Setting
1 ADJ Temperature
calibration
2 SEN Sensor mode
3. LIT Limitation
temperature
4 DIF Switching
differential
5 LTP Antifreeze
function
6 PRG Set vacation
mode
7 RLE Potential - free
output and main
power output in
the
same/different
way
8 DLY Delay time of
Potential - free
output
9 HIT
Max temperature
AFAC Reset to factory
settings
Sensor failure:
" to
Please select the right sensor mode when operation, it will display the
"Err" symbol on screen far sensor failure, thermostat must be checked till
the fault is eliminated
Explanation of symbols:
Manual mode
Six period
Time
Week
Menu
Increase key
Dimension:
Unit: mm
86
biuro@warmtec.pl

Installation Manual

08:00 22℃
23:00 15℃
" and turn on it at the
or
Adjust measured temperature
IN: built-in sensor
OUT: floor sensor
ALL: both sens o rs
Adjust limitation value,
Limitation range:5 ℃ ~60℃
Adjust switching differential
Turn on/off Anti-frozen
function
00: 5/2 day mode
01: 6/1 day mode
02: 7 day mode
Change the present
linkage way
Change linkage delay time
Limitation temperature
setpoin t
"and hold for 5s ， all
Press "
parameters will be reset
Period mode
Antifreeze
temperature
Lock key
heating
power
NTC
Decrease key
43
13
V. 1.02