Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Premier MDP-4807C
Summary of Contents for Premier MDP-4807C
- Page 1 MDP-4807C...
- Page 2 WWW.PREMIERMUNDO.COM WWW.PREMIERMUNDO.COM IMPORTANT NOTICE THINGS TO DO BEFORE OPERATING YOUR NEW COMPRESSOR FOR THE FIRST TIME 1. On the top front of the compressor you will find a white plastic shipping plug inserted into the Oil Filler Hole. Remove the shipping plug and replace by pressing the red Oil Filler Plug (supplied in the parts bag) into the Oil Filler Hole.
-
Page 3: Table Of Contents
WWW.PREMIERMUNDO.COM WWW.PREMIERMUNDO.COM CONTENTS 1、INTRODUCTION………………………………………………2 2、SAFETY GUIDELINES ……………………………………… 2 3、BRIEF DESCRIPTION ………………………………………4 4、GENERAL VIEW AND MAIN COMPONETS …… … … … 4 5、MAIN TECHNICAL PARAMETER………………………… 4 6、PREPARATION FOR STARTING ………………………… 5 7、OPERATION AND ADJUSTMENT ……………………… 5 8、CAUTIONS …………………………………………………… 6 9、MAINTENANCE …………………………………………………6 10、TROUBLES AND REMEDIES………………………………... -
Page 4: 1、Introduction
WWW.PREMIERMUNDO.COM WWW.PREMIERMUNDO.COM 1.INTRODUCTION Read this manual carefully before operating or servicing this, air compressor to familiarize yourself with proper safety, operation, and main tenance procedures. Failure to comply with instructions in this manual could result in personal injury, property damage, and/or voiding of your warranty. Following the instructions in this manual will provide a longer and safer service life for you air compressor. - Page 5 WWW.PREMIERMUNDO.COM WWW.PREMIERMUNDO.COM remove the plug from the outletr, and bleed all pressure from the system before servicing the compressor, and when the compressor is not in use. 4. Chcck the manufacturer'rs maximum pressure rating for air tools and accessories. Compressor outlet pressure must be regu lated so as to never exceed the maximum pressure rating of the tool.
-
Page 6: 3、Brief Description
(4)Regulating Valve (5)Pressure gauge (6)One-way Valve (7)Drain cock (8)Wheel (9)Discharge pipe (10)Air tank (11)Fan cover Fig.1 、 5 MAIN THCHNICAL PARAMETER Model MDP-4807C Power 2HP/2.5HP/3HP Voltage 220V Frequency 50Hz Current 17A/17.5A Rated Speed 2850r/min Displacement 156L/min | 206L/min | 248L/min Max.Working Pressure... -
Page 7: 6、Preparation For Starting
WWW.PREMIERMUNDO.COM WWW.PREMIERMUNDO.COM 、 6 PREPARATION FOR STARTING (1)The place to set the compressor should be clean,dry and ventilated. ± (2)Keep the use voltage within 5% of rated. (3)Keep the oil level in the red circle leveler. ℃ (4)Recommend compressor oil use SAE30 or L-DAB 100 over 10 ,and use SAE10 or ℃... -
Page 8: 8、Cautions
WWW.PREMIERMUNDO.COM WWW.PREMIERMUNDO.COM 、 8 CAUTIONS (1)Put the cover off first and put on the breath pipe and air filter before the compressor run(Fig.3). Air filter (2)Never unscrew any connecting part when the tank is in pressure condition. (3)Never disassemble any electrical part before disconnecting the plug. -
Page 9: 10、Troubles And Remedies
WWW.PREMIERMUNDO.COM WWW.PREMIERMUNDO.COM 、 10 TROUBLES AND REMEDIES Table 2 Possble causes Trouble Remedies (1)Fault in line,or voltage insufficient Mortor unable (1)Check the line (2)Power wire too thin or too long running, (2)Replace the wire (3)Fault in pressure switch Running too (3)Repair or replace (4)Fault in motor Slow, or... -
Page 10: 11、Parts Illustration
WWW.PREMIERMUNDO.COM WWW.PREMIERMUNDO.COM 、 11 PARTS ILLUSTRATION... -
Page 11: Parts List
WWW.PREMIERMUNDO.COM WWW.PREMIERMUNDO.COM PARTS LIST Designation Designation Q'ty Q'ty Piston ring Fan cover Piston Capacitor Hex Belt Circlip Nut M8 Piston pin Connecting rod Screw Screw Crank Bolt M8 22-right Hex Belt Washer Rubber gasket Spring Crank case cover Breath pipe Nut M8 Screw m5 Stem...
Need help?
Do you have a question about the MDP-4807C and is the answer not in the manual?
Questions and answers