Summary of Contents for Lanner HLM-1001
- Page 1 Telecom Datacenter Appliances HLM-1001 User Manual Version: 1.0 Date of Release: 2018-09-26...
- Page 2 HLM-1001 User Manual The icons are used in the manual to serve as an indication of interest topics or important messages. Below is a description of these icons: Note: This check mark indicates that there is a note of interest and is something that you should pay special attention to while using the product.
- Page 3 instruction manual, may cause harmful interference to radio communications. The operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
- Page 4 HLM-1001 User Manual Suivez ces consignes pour assurer la sécurité générale : Laissez la zone du châssis propre et sans poussière pendant et après l’installation. Ne portez pas de vêtements amples ou de bijoux qui pourraient être pris dans le châssis. Attachez votre cravate ou écharpe et remontez vos manches.
- Page 5 Version Date Descriptions 2018/09/26 Official Release...
- Page 6 HLM-1001 User Manual Ordering Information ........................7 System Specifications ........................7 I/O Overview..........................8 Block Diagram ..........................9 Motherboard Layout ........................10 Internal Jumper & Connectors ....................11 Replacing Front Network I/O Blades & Switch Boards .............. 15 Warranty Policy .......................... 16 RMA Service ..........................
-
Page 7: Chapter 1: Product Overview
Chapter 1: Product Overview The HLM-1001 supports up to 32-port 10GbE SFP with NIC Module which uses Intel XL710 Ethernet Controller. It can be installed into latest Lanner HTCA-6000 Series network appliances. Intel XL710 Ethernet Controller 32-port 10GbE SFP+ cage Compatible with HTCA-6600 and HTCA-6200 SKU No. - Page 8 HLM-1001 User Manual Description 10GbE SFP+ Ports PCIE 3.0 x8 Press-fit connector...
-
Page 9: Chapter 2: Motherboard Information
Chapter 2: Motherboard Information The block diagram indicates how data flows among components on the motherboard. Please refer to the following figure for your motherboard’s layout design. - Page 10 HLM-1001 User Manual The motherboard layout shows the connectors and jumpers on the board. Refer to the following picture as a reference of the pin assignments and the internal connectors. CON1 CON2...
- Page 11 Chapter 2: Motherboard Information P1: Power connector (Press-fit) Description Description +12V +12V +12V +12V +12V +12V +12V +12V CON1/2: Fan Power connector Description +12V J1: PCIe Card Connector CPU1_PE3ATP2 CPU1_PE2CTP10 CPU1_PE2CTP8 CPU1_PE2CTN1 CPU1_PE3ATP1 CPU1_PE3ATN2 CPU1_PE3ATP3 CPU1_PE2CTP9 CPU1_PE2CTN8 CPU1_PE3ATN1 CPU1_PE3ATN3 CPU1_PE2CTN9 CPU1_PE3BTP6 CPU1_PE2ATP0 CPU1_PE2ATP2...
- Page 12 HLM-1001 User Manual CPU1_PE2DTP12 CPU1_PE2DTP14 BOARD_ID0 CPU1_PE2CTP11 CPU1_PE2DTN12 CPU1_PE2DTP13 CPU1_PE2DTN14 CPU1_PE2DTP15 PRESENT# CPU1_PE2CTN11 CPU1_PE2DTN13 CPU1_PE2DTN15 CPU1_PE2BTP4 CPU1_PE2BTP6 CPU1_PE2ATP3 CPU1_PE2BTN4 CPU1_PE2BTP5 CPU1_PE2BTN6 CPU1_PE2BTP7 CPU1_PE2ATN3 CPU1_PE2BTN5 CPU1_PE2BTN7 CPU1_PE2CRP11 CPU1_PE2DRP13 IPMI_DATA CPU1_PE2CRP10 CPU1_PE2CRN11 CPU1_PE2DRP12 CPU1_PE2DRN13 CPU1_PE2DRP15 IPMI_CLK CPU1_PE2CRN10 CPU1_PE2DRN12 CPU1_PE2DRN15 CPU1_PE2BRP4 CPU1_PE2BRP6 PCIE_RESET#...
- Page 13 Chapter 2: Motherboard Information J2: PCIe Card Connector CPU2_PE1ATP3 CPU2_PE2DTP15 CPU2_PE2DTP13 CPU2_PE1ATP1 CPU2_PE1ATN3 CPU2_PE1ATP2 CPU2_PE2DTN15 CPU2_PE2DTP14 CPU2_PE2DTN13 CPU2_PE1ATN1 CPU2_PE1ATN2 CPU2_PE2DTN14 CPU2_PE1ARP2 CPU2_PE2CRP8 CPU2_PE2CRP10 CPU2_PE1ATN0 CPU2_PE1ARN2 CPU2_PE1ARP1 CPU2_PE2CRN8 CPU2_PE2CRP9 CPU2_PE2CRN10 CPU2_PE1ATP0 CPU2_PE1ARN1 CPU2_PE2CRN9 CPU2_PE1BTN6 CPU2_PE3BTP7 CPU2_PE3ATP1 CPU2_PE1ARP3 CPU2_PE1BTP6 CPU2_PE1BTN7 CPU2_PE3BTN7 CPU2_PE3ATP0 CPU2_PE3ATN1 CPU2_PE1ARN3 CPU2_PE1BTP7...
- Page 14 HLM-1001 User Manual PCIE_CLK_N PCIE_CLK_P...
-
Page 15: Chapter 3: Hardware Setup
Chapter 3: Hardware Setup To access some components and perform certain service procedures, you must perform the following procedures first. Warning: To reduce the risk of personal injury, electric shock, or damage to the equipment, remove the power cord to remove power from the server. The front panel Power On/Standby button does not completely shut off system power. - Page 16 1. All products are under warranty against defects in materials and workmanship for a period of one year from the date of purchase. 2. The buyer will bear the return freight charges for goods returned for repair within the warranty period; whereas the manufacturer will bear the after service freight charges for goods returned to the user.
- Page 17 Appendix: Terms and Conditions When requesting RMA service, please fill out the following form. Without this form enclosed, your RMA cannot be processed.
Need help?
Do you have a question about the HLM-1001 and is the answer not in the manual?
Questions and answers