Malem Ultimate Vibro-Watch + Operation Manual

Malem
™
11. Change Alarm time
• Press 'M' key twice to enter the Alarm
Setting Mode. Wait for 5 seconds while
loading.
• "ALARM SET" appears on the matrix zone.
• Previous set alarm will display
• Pre-selected alarm number, time and
animation wording are displayed (If active)
• Toggle 'S' key to desired alarm number
(1-2-3-4-5-6-7-8-9-10-11-12)
• Press and hold 'S' key for 3 seconds until
the Minute digits flash
• Press 'C' key to adjust alarm time in
minutes
• Press 'S' key to fix the Minute setting, then
Hour digits will flash
• Press 'C' key to adjust alarm time in hours
• Press 'S' key to fix hour setting.
• Press 'M' key back to Real Time display
12. Change Auto Repeat
Alarm time:
• Press 'M' key twice to enter Alarm Setting
Mode (wait for 5 seconds while loading) Month/Hour Date/Minute
• Word "ALARM SET" rolling on matrix zone
ALEM
TM
• Pre-selected alarm number, time and
animation word are displayed. (If active)
Repeat
Timer
• Toggle 'S' key until to icon appears.
©
RO-WATCH
troluminescence Lock
1 2 3 4 5 6
(After alarm 12)
7 8 9 10 11 12
• Press and hold S key for 3 seconds until
12-Alarms Day/Second
Minute digit flashes
ont View
LCD Display
• Press 'C' key to select desired count-down
time in minutes
• Press 'S' key to confirm setting and the
Hour digits flash
• Press 'C' key to select desired count-down
pen/Close
ndicator
time in hours
Lift metal tab slightly
▼
• Press 'S' key to confirm setting when replacing battery
●
●
• Word "START" shown on matrix zone,
LITHIUM
BATTERY
CR-1632
CR-1632
+
Minute digits flash (Useful to define
MALEM
MALEM
TM Serial Number
TM
part of day you need the periodic auto-
odel MO22
repeat alarm to be active day or night)
• Press 'C' key to select desired start
©
VIBRO-WATCH
Electroluminescence
activation time in minutes
Battery
ck View
Compartment
• Press 'S' key to confirm setting and the
Label
Hour digits flash
Front View
• Press 'C' key to select desired start
activation time in hours
• Press 'S' key to confirm setting
• Word "END" appears on matrix zone, and
Open/Close
the Minute digits flash
Indicator
• Press 'C' key to select the desired count-
▼
down time end in minutes ●
●
• Press 'S key to confirm setting and the
CR-1632
Hour digits flash
MALEM
TM
Model MO22
Back View
Ultimate Vibro-Watch +
• Press 'C' key to select desired count-down
time end in hours
• Press 'S' key to confirm setting
• Press 'M' key back to Real Time display
13. Change Animation Words
Specific time alarm:
• Press 'M' key twice to enter the Alarm
Setting Mode. Wait for 5 seconds while
loading.
• "ALARM SET" appears on the matrix zone.
• Previous set alarm will display
• Pre-selected alarm number, time and
animation wording are displayed (If active)
• Toggle 'S' key to desired alarm number
1 - 3 - 5 - 7 - 9 - 1 1
(1-2-3-4-5-6-7-8-9-10-11-12)
• Press and hold 'S' key for 3 seconds until
the Minute digits flash
• Press 'S' key to skip setting and the
Hour digits flash
• Press 'S' key to skip Hour setting
• Animation Words appears on matrix zone
Toggle 'C' key to select an appropriate word
from the following.
'Hello, Wake Up, Toilet 1, Toilet 2,
Wash, Dress, Eat, Drink, Medicine,
Exercise, Appointment, Visitor and Bed CR-1632
Alarm Format
Lithium
Sound Time.'
Battery
Vibration
• Press 'S' key to confirm selection
• Press 'M' key back to Real Time display
Compartment
14. Change Animation Words
Label
Battery Door
Auto Repeat Timer:
Opener
• Press 'M' key twice to enter the Alarm
Setting Mode. Wait for 5 seconds while
loading.
• "ALARM SET" appears on the matrix zone.
• Previous set alarm will display
• Pre-selected alarm number, time and
Month/Hour Date/Minute
For
animation wording are displayed (If active)
'O'Ring
Professional
(Do not lose) Use Only
• Toggle 'S' key to skip alarm number
Model
MO22
(1-2-3-4-5-6-7-8-9-10-11-12) until the Alarm Format
Repeat
Timer Sound
icon for Auto-Repeat Timer Alarm
Vibration
Lock Battery Door
1 2 3 4 5 6
appears
Opener
7 8 9 10 11 12
and
• Press and hold 'S' key for 3 seconds until
Battery Holder
12-Alarms Day/Second
the Minutes digit flash To avoid damage use
a watch repair shop
LCD Display
• Press 'S' key to skip setting and Hour digits
flash
• Press 'S' key to skip Hour setting
• Press 'S' key 4 times to skip start time and
end time
• Animation Words appears on matrix zone
Lift metal tab slightly
Toggle 'C' key to select an appropriate word
when replacing battery
from the following: 'Hello, Wake Up,
LITHIUM
BATTERY
CR-1632
+ 'O'Ring
Toilet 1, Toilet 2, Wash, Dress, Eat,
(Do not lose)
Serial Number
Drink, Medicine, Exercise, Appointment,
Visitor and Bed Time.'
Battery
Compartment
Label

Operation Manual

• Press 'S' key to confirm selection
• Press 'M' key back to Real Time display

15. Battery Replacement:

It is recommended that you use a watch repair
shop to prevent damage to the watch. Battery:
CR2032 (battery life is about 3 months when
new. Depends on use). When the old battery is
removed no programmed data will be lost on
the watch, but you will have to adjust the time
again once a new battery is in place.
AM 1 - 3 - 5 - 7 -
PM
-
CLOSE
MODEL
MO21
1. To remove the old battery (use appropriate
coin fit the slot) twist battery cover 3
degrees anti-clockwise (see arrows by
the right hand side of the battery cover).
BATTERY
Ease/loosen cover.
CR2032
2. Make sure you do not lose the 'O' ring
inside the rim.
Observe the
3. Pull metal contact strip in base of the watch
correct polarity
CLOSE CLOSE
slightly upwards (see drawing) to ensure
good battery contact with metal connectors
4. Press all four buttons at the same time for 2
seconds
5. Place new battery in the battery cover with
MODEL OD D E E E E L L
the correct polarity (See diagram)
MO21 O2 2 1 1 1
6. Line up arrow on battery cover with open
arrow on back. Make sure 'O' ring is
correctly in place to prevent water/moisture
CR-1632
Lithium
ingress.
Battery
7. Insert in battery compartment making sure
that contact is made once and not
repeatedly as this may blank or corrupt the
Compartment
Label
display and prevent the watch from
Battery Door
working. Watch will vibrate for a second
Opener
when battery makes contact.
8. Turn cover clockwise (using the coin) to
the closed position. Arrow lines up with the
wording 'close'
9. If watch display is blank or corrupted, start
at step 1.
For
Professional
Use Only
Model
MO22
Battery Door
Opener
and
Battery Holder
To avoid damage use
16. Please note:
The Malem Ultimate Vibro-Watch© is not water
proof due to the speaker holes on the front of
the watch.
17. Guarantee:
The Malem Ultimate Vibro-Watch© guarantee
covers manufacturing defects for one year from
date of purchase. It does not cover battery,
glass, strap, discolouration or damage caused
by wear and tear, water, abuse or misuse.
18. Disclaimer:
AM
PM
Please note the Malem Ultimate Vibro-Watch©
9 - 1 1 -
is designed as a helpful vibration/message
CLOSE
reminder. It is not intended to replace human
care or supervision and the manufacturer,
Malem Medical Ltd, is not responsible for
any consequences resulting from watch use,
misuse or failure.
19. Copyright:
MODEL
Malem™ and Ultimate Vibro-Watch©+ MO21
MO21
are Trade Mark and copyright protected ©
2014. Malem Medical Ltd reserves the right to
change the specifications without prior notice.
BATTERY
CR2032
Metal
Contact
Observe the
Strip
correct polarity
CLOSE CLOSE
MODEL OD D E E E E L L
MO21 O2 2 1 1 1
To avoid damage to the battery
cover slot, please use appropriately
sized coin
Malem Medical Ltd
10 Willow Holt
Lowdham
Nottingham
NG14 7EJ
England, UK
Tel: + 44 (0)115 966 4440
Fax: + 44 (0)115 966 4672
E-mail: malem@malem.co.uk
Web: www.malem.co.uk
Web: www.malemmedical.com
© Malem Medical 2014
Malem Medical Ltd reserves the right to
change the specifications without prior
notice.
MO21/007/14