Table of Contents
Advertisement
Quick Links
--1075 North Ave. Sanger, CA 93657-3539
Congratulations! You were selective enough to choose a BELLTECH PRODUCT. We have spent
many hours developing our line of products so that you will receive maximum
performance with minimum difficulty during installation.
Note:
Confirm that all of the hardware listed in the parts list is in the kit. Do not begin installation if
any part is missing. Read the instructions thoroughly before beginning this installation.
Warning:
DO NOT work under a vehicle supported by only a jack. Place support stands securely under
the vehicle in the manufacturer's specified locations unless otherwise instructed.
Warning:
DO NOT drive vehicle until all work has been completed and checked. Torque all hardware to
values specified.
Reminder:
Proper use of safety equipment and eye/face/hand protection is absolutely necessary when
using these tools to perform procedures!
Note:
It is very helpful to have an assistant available during installation.
RECOMMENDED TOOLS:
• Properly rated floor jack and 4 (2) support stands
• Wheel chocks
• Drill motor with 5/16" twist drill bit
• Standard socket wrench set
• Standard box wrench set
• ½" drive torque wrench (lb-ft)
• Safety glasses
!
PLEASE NOTE: For your safety and to prevent possible damage to your vehicle, do not exceed the
maximum load recommended by the vehicle manufacturer (GVWR). Although your Air Assist Springs are rated
at a maximum inflation pressure of 100 P.S.I., this pressure may allow you to carry more than specified GVW on
some vehicles. It is best to have your vehicle weighed once it is completely loaded and compare that weight to the
maximum allowed. Check your vehicle owner's manual or data plate on driver's side door for maximum loads
listed for your vehicle
SAFETY REMINDER: PROPER USE OF SAFETY EQUIPMENT AND EYE/FACE/HAND PROTECTION
KIT INSTALLATION
As this is a relatively involved installation, we recommend that a qualified mechanic at a properly equipped
facility perform it. We also recommend that the installation be performed on a firm, flat and level surface,
such as seasoned asphalt or concrete. The use of safe and properly maintained equipment is very important!
5008-888 8/05 ©
A Division of KW AUTOMOTIVE North America, Inc.
local: 559-875-0222
AIR JACK KIT
(WITH BELLTECH C-NOTCH)
1999-UP CHEVROLET SILVERALDO
IS ABSOLUTELY NECESSARY WHEN USING THESE TOOLS TO PERFORM
PROCEDURES!
INSTALLATION INSTRUCTIONS
fax: 559-876-2259
5008
1
toll free:
800-445-3767--
Advertisement
Table of Contents
Summary of Contents for Belltech 5008
- Page 1 AIR JACK KIT (WITH BELLTECH C-NOTCH) 1999-UP CHEVROLET SILVERALDO Congratulations! You were selective enough to choose a BELLTECH PRODUCT. We have spent many hours developing our line of products so that you will receive maximum performance with minimum difficulty during installation.
- Page 2 2. FITTING THE UPPER BRACKETS a) With the rear of the vehicle supported, remove the rear wheals. b) Working from either side of the vehicle, remove the four bolts from the rear of the Belltech C- notch (Photo 1). c) Slide the upper bracket onto the frame rail, making sure that the upper bracket sits flat against the C-notch (Photo 2).
- Page 3 5/16” hole in the upper bracket (Photo 12). c) Route the airline through the back of the Belltech C-notch (Photo 13) and through the 5/16” hole on the bracket on the other side of the vehicle. Insert the loose end into the other fitting so that the airline runs from one air spring to another.
- Page 4 (front to rear). This amount will vary depending on the load, location of load, condition of existing suspension and personal preference. 5008-888 8/05 © A Division of KW AUTOMOTIVE North America, Inc.
- Page 5 110258 3/8 -16 x 3/4 HHCS 5096-015 1/4 Elbow Fitting 5096-020 1/4 “T” Fitting 5096-017 1/4 Schrader Valve 9999-975 Nylon Ties 7” 112258 U-Clamp 3” 5008-301 ½” Insulated Clamp 5008-888 8/05 © A Division of KW AUTOMOTIVE North America, Inc.
- Page 6 5008-888 8/05 © A Division of KW AUTOMOTIVE North America, Inc.
- Page 7 5008-888 8/05 © A Division of KW AUTOMOTIVE North America, Inc.
Need help?
Do you have a question about the 5008 and is the answer not in the manual?
Questions and answers